The product is employs asphalt or thermoplastic elastomer (styrene â?? butadiene block copolymer SBS), modified asphalt impregnated base. Both sides are coated with elastomer or plastic bitumen,upper surface is sprinkled with fine sand , mineral grains (membrane) or coverage polyethylene film,and underside with fine sand or coverage from polyethylene membrane.
The product has good waterproof performance and anti-aging performance, and has the characteristics of not flowing at high temperature, not brittle crack at low temperature, simple construction, no pollution, long service life.It is mainly used in the industrial and civil building roofingã??bathroomã??basementã??pond , bridge, parking lot, swimming pool, tunnel, reservoir and other buildings waterproof, moisture-proof, waterproof steam.Impermeability and maintenance of asphalt roofing.sbs Modified asphalt waterproof rolling material is especially suitable for waterproofing of buildings in cold areas and areas with frequent structural deformation.
Environmental protection products, water-based tasteless, convenient construction, wide range of application, the construction of complex parts has obvious advantages. After curing the formation of non-joint, complete elastic waterproof layer, improve the waterproof and impermeability of construction engineering, is rolls material. Itâ??s impossible to reach the product. The film has high strength and elongation, and has strong adaptability to cracking or expansion of the base. The maintenance is convenient, only to the damaged part partial maintenance, still can achieve the original waterproof effect. This product has bright color, can play the role of decoration and beautification, the moisture content of the base is not strict, wet base surface can be constructed.
Supplier: Sbs modified bitumen waterproofing rolls,app bitumen waterproofing rolls,butyl rubber waterproof tape,pvc waterproofing rolls,pp pe fiber polymer waterproofing rolls, ldpe bag, hdpe bags
1.Brand name jianda Surface pe, s, m Size 1mx10m, 1mx8m Fetus: composite tires or polyester With one side adhesive side pe film as a benchmark, can customize the double-sided adhesive/sand shale surface/aluminum foil/face/colour sand surface Type 2: standard: gb/t23441-2009 Low tender degrees: - 20 or 25 Body: polyester tire Thickness of 1.5 mm at least Packed in rolls with pallet/ or as per clients' requirement
It uses high-quality butimen with SBS thermoplastic elastomer as modification additive and prepared by special technology. There is reinforcment in the middle and covered with various surface materials. Advantage: 1. Excellent low temperature resistance. 2. High tensile strength and elongation. 3. Excellent tear, corrosion and weather resistance. 4. Hot melt construction with reliable and durable seams. Application: Waterproof and moisture proof works for roof and underground space of various buildings. Specification: 1. Thickness: 3/4/5mm 2. Width: 1000/2000mm 3. Length: 10/15m
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
The products are made by soaking the base in bituminous or thermo plasticity elastomeror thermoplastics modified bitumenous, then covering double faces with elastomer(SBS)or thermoplastics(APP,APAO,APL)modified bitumenous, and last finishing the upward face with fine sands, mineral slates(or grains)or polythene membrane while downward face with fine sands or polythene membrane. 100mm*10m
The products are made by soaking the base in bituminous or thermo plasticity elastomer(such an styrene butadiene styrenef¼SBS),or thermoplastics(such as atactic Polypropylene---APP,APAO,APL)modified bitumenous, then covering double faces with elastomer(SBS)or thermoplastics(APP,APAO,APL)modified bitumenous, and last finishing the upward face with fine sands, mineral slates(or grains)or polythene membrane while downward face with fine sands or polythene membrane. good self heating, easy application, and long service, etc.
SBS modified bitumen waterproof membrane takes SBS (styrene-butadiene- styrene) thermoplastic elastomer modified asphalt mixed with additives as base materials, using premium polyester (PY), fiberglass (G), fiberglass & polyethylene felt (PYG) as matrix , and adopting sand (S), mineral granule (M), polyethylene film (PE), aluminum foil etc as dip-coat, which is produced by stirring and grinding with special equipment. Features A)Good low temperature flexibility,it has no crack when temperature drops into -20â??;Excellent heat resistance, it has no flow when temperature reaches 90â?? B)Great tensity,prolonged life span,easy to use C)Suitable forâ? and â?¡grade constructional waterproofing project,especially for cold area and the project of frequent structural deformation Size Available â?¢Width-3.28ftï¼?1mï¼? â?¢Length-24.6ft(7.5m) 32.8ft(10m)49.2ft(15m) â?¢Thickness- PY (3mm,4mm,5mm) G (3mm,4mm) APP modified bitumen waterproofing membrane based on APP (atactic polypropylene) or APAO, APO (It is reported that tiring polymer) modified asphalt roofing, high-quality polyester felt, fiberglass mat base for the child, with fine sand and mineral tablets (piece) material, PE film for the cladding material, the use of advanced technology refined plastomer modified bitumen membrane. Features A)Good elongation;Good anti-weathering;Excellent flexibility B)Strong adhesion;High strength;Anti-abrasion and anti-impact C)Superior High and low temperature resistance,especially for hot areas D)Easy to apply,heat-welded;Anti-corrosion,anti-mildew ADVANTAGES â?¢Over 1000 cases in waterproofing projects â?¢Accredited contract observing enterprise â?¢15 years of experience in waterproofing industry â?¢Self-contained production line,sound and completed production management systems â?¢Multiple advanced first-class production devices,laboratories,experienced researching panels â?¢3 years of innovation in production craftmanship and 10 proprietary products Guangdong Tenjoy has two brands of building materials-- Tenjoy,Zolon,fits in the needs of residential construction and industrial construction waterproofing projects,which is specialized in the development,production and sales of waterproofing material,including waterproofing membrane,waterproof coating,waterproofing mortar,lost circulation material, water stop and so forth. Given the strong power in product development,a wide range of measuring instruments,the automatic production line of bituminous waterproofing membrane and macromolecule waterproof coating,water stop,automatic paint mixer and racking machine,we can fully meet the needs of domestic major engineering projects with the annual production capacity of 10 million square meters in waterproof membrane,60 thousand tons of paint,8 tons of waterproof slurry.
Jute (including kenaf) was an important foreign exchange earner for the producing countries during '60s. Even during the '70s, jute was an important commodity for most of the producing countries. However, during the '80s, bulk handling techniques and synthetic substitutes entered the market and jute started losing its predominant position in the market.
