Ccs
Sheet thickness:0.14mm~1.0mm,
Sheet width:800mm~1250mm
Coat thickness: primercoat:5~10um, finish coat:10~25um
Coil wight:max6mt
Coil id:508mm
We , Niko is in oil & Gas Exploration and production file, procured the Pipe fitting require for its operation at different stage of project. We have the left out stock of these project inventory which include the CS/MS pipe fitting of different size. Now as we doesn’t required these stock more , we are in search of the potential buyer for the same. We have attached the list of the same for your ref with snaps. Request to confirm your INTEREST TO PURCAHSE THE SAME for your existing customer. Waiting for your reply for the same.
DESCRIPTION CC-200 is a indoor, high fluidity, rapid strength and leveling material. It still has high bonding,low shrinkage, low water absorption, acid resistance, alkyl resistance and chemical resistance. It special use for fast repairing, putty and leveling for epoxy coating. APPLICATION Floor fixing on parking garage, factory, and warehouse. Leveling before epoxy coating. Basic layer for non natural paint. Bec ause of the early strength and low moisture content, CC 200 has widely application. Contact out agent when you have doubt on CC 200. ADVANTAGES 1. Curing and enhancing are fast and rapid below 25 mins. High strength and low water absorption/ content could be reached after curing. 2. Good acid and alkyl resistance. 3. Good wear resistance, high compressive strength, leveling and anti cracking. PREPARE TO USE 1. Clean with vacuum to ensure the surface dustless. 2. Working site is free from dust, sand, oil, and loose. a). Crack and Joint Treatment b). File on the crack, open a width of 2 3 cm depth of 1 cm or more groove joints and clean up dust and loose. c). At the same time taking CC 200 mortar, filled in and up the crack and sizing 1 2 times primer after 2 4 hours. 4. Shorter wor king hours to achieve saving time, fast leveling and convenience work.
Description 1. Tough film and good adhesion on the concrete, able to penetrate into concrete. 2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties. 3. Good resistance to impact and abrasion. 4. Easy application , drying fast. Prepare to use 1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity. 2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application. 3. Two packs product, must be used completely during the duration of its pot life. 4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??. 5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion. 6. Keep away from heat, sparks and flame. 7. Stored with good ventilation. 8. Keep adequate ventilation during application. 9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying. **The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel. Color : Clear Drying time : Tack-free : 2 hours Hardness : 8 hours Full cure : 7 days (grease)
DESCRIPTION CC-600SP is a two component, solvent-free epoxy system with high chemical resistance and high bond strength. The epoxy may be applied as a primer for most high end industrial coatings, like Epoxies, PU. CHARATERISTIC Easy apply Low odor High bond strength Abrasion resistant Chemical resistant APPLICATION Concrete coating Cement
Description CC-500 Dura-Shine is one component, aliphatic, UV resistant polyurethane based topcoat membrane. Product cures with the humidity and produces a transparent film and by this way it provides excellent adhesion over the entire surface. Feature Resistant to UV, exposed sunlight and chemicals When applied, it forms as seamless membrane without joints Product keeps its mechanical features over a temperature span of 40 to 90 degrees Celsius Use Area Roof terraces balconies and verandas Industrial floor coatings Stadium, car parks Stones, marble and ceramic surfaces Coverage Consumption of each layer: 0.1-0.15 kg/m2 Minimum two coats should be applied Total consumption: approx. 0.2-0.3 kg/m2 Recoating: Do not exceed 48 hours between each coats. Application must be repeated if this time is exceeded
CC-403 Epilox Epoxy Binder is a two part solvent free epoxy resin binder system for combining with selected fillers and aggregate to produce epoxy mortars of various consistencies. Ideal for : bonding, sealing, priming, coating and grouting. May be used on vertical or horizontal applications as structural epoxy adhesive paste and filler. CC-403 is also used as a primer for Epilox floor coatings and toppings as well as Epilox mortars. FEATURES AND BENEFITS 100% solids epoxy Solvent free Low VOC High tensile and compressive strength Bonds to damp concrete High mechanical strength Excellent adhesion to most substrates Cures at temperature down to 5Ã??C High chemical resistance Unfilled system Allows for mortars and grouts to be mixed to any desirable consistency Typically 3-4 times stronger than typical concrete Complies with AS4020 potable water Australian Made Convenient mix ratio- ( 2 parts Resin- 1 part Hardener ).
DESCRIPTION CC-604SP is two component water based epoxy primer, composed from water based of liquid epoxy resin and hardener. APPLICATION 1. To prime the surface and help the following application procedure to mold and decorative coating. 2. Highly resist to chemicals in non-circulated places. 3. With well adhesion ability with epoxy system or PU system application. 4. Suitable for hospital, operation room, food factory to prevent the mold, dust and bacterium. CHARATERISTIC 1. Able to be diluted by water. 2. Anti- efflorescence , suitable for the environment with highly hygienic request. 3. Good adhesion to the moisture surface, can take as the primer for solvent-free or solvent-based epoxy resin.
DESCRIPTION CC-103(1K) Crystalline Waterproofing Materials is fusion resin powders which contains water-soluble crystalline mineral coating with special additive syntheses. It will have a protective coating which is firm and impact resistance after curing. CC-103(1K) is a high technology product to prevent water leakage. ADVANTAGES * Prevent the constructions aging phenomenon * Avoid the leakage and mold on the wall * Effective against negative water pressure * With good stability * Non-Toxic APPLICATION * Internal and external walls * The leakage of inner wall in basements or the protection against negative water pressure * The construction of base isolated structures * Reservoir; drinking water pool * Contaminated water pool; water storage tank PROCEDURE 1. Ensure all surfaces which CC-103(1K) will be applied are clear. 2. Mix one pail(22.5KG) of CC-103(1K) and 4.5~5.0Liter water well by construction mixer. 3. Wait for 3-5 minutes and stir before use; use finishing trowel to smoothing or apply evenly with a nap roller. 4. Use finishing trowel to smoothing after using spray machine. PACKING 22.5KG per pail. STORAGE 6 months in original container stored in dry conditions. LIMITATION The crystalline products need to be used between 4 °C ~ 32 °C when applied.
DESCRIPTION CC-103(2K) Crystalline Waterproofing Materials is a capillary waterproofing formulation. CC-103(2K) has high permeability which crystallize and penetrate deeply into the capillaries of the concrete. ADVANTAGES * Applied to wet surface * Transparent, non-toxic and odorless * High cohesion and effective against positive/negative water pressure well APPLICATION * The leakage of inner wall in basements or the protection against positive/negative water pressure * Prevent seepage and leakage in underground passages and tunnels * Avoid the leakage of cisterns and pools PACKING 30KG/Set A: 22.5KG in powder.+ B: 7.5KG additive. COLOR Grey and white. STORAGE 6 months in original container stored in dry conditions and under 25°C.