Supplier: Wireless charger, batteries power bank, dust sensor, optical disc drive, tof, lidar, ar glass
Supplier: Wired magnetic door sensors.
Description PS1 is a radar sensor, which uses microwave doppler technology for activation of door. It can be mounted on all types of standard automatic doors. PS1 is with unidirectionality function, to reduce the heat loss from building and save energy. Function and Advantages Mounting height up to 5m Unidirectional and bidirectional detection optional Intelligently opening & closing Precise detection with high stability TABLE OF SPECIFICATIONS Technology: Microwave doppler radar Transmitter frequency: 24.150 GHz Transmitter radiated power: < 20 dBm EIRP Transmitter power density: < 5 mW/cm² Min. detection speed: 5 cm/s Supply voltage: 12V - 24V AC -/+10% 12V -24V DC +30%/-10% Mains frequency: 50 Hz - 60 Hz Max power consumption: < 2 W
Supplier: Electrical materials, electrical equipments, lighting fixtures, plumbing materials, ac materials, it materials, ceiling materials, partition materials, painting materials, floor tiles, hardware materials, hand tools & power tools, garage tools, wooden & carpenter materials, batteries. medical equipment and medical consumable product and medical surgical equipment.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Capillary cable is composed of a submersible power cable and a continuous stainless steel composite pipe. Diluent chemicals are injected into oil and gas Wells through composite pipes to make heavy oil Wells easier to recover. The injection of descaling chemical agent can effectively remove the oil pipe scaling. Sensors can be connected to collect downhole temperature, pressure, liquid level and other well parameters; The valve can be connected to the downhole safety valve and the wireline packer vent valve, and controlled on and off by surface pressure.
Mine detection cable is mainly used in various oil and gas Wells with Oil well wax removal, viscosity reduction and coagulation reduction, coring and well logging, perforation etc., can also be used in ocean research and river, harbor, water conservancy hydrological measurement, as well as coal field geological prospecting, geothermal well logging, etc.,The detection cable is connected with the sensor and the signal terminal, which has a strong anti-interference signal transmission function.
Instrumentation circuits cable is used for computer based automatic control system, especially for computer distributed control system, transmission of production device process variable detection, control, interlocking, alarm lamp analog and digital signals, the product has excellent anti-interference performance, long-term working temperature -40~105.