Blue Jay company developed using semiconductor technology, in a certain place to lead controlled condensation, make the cabinet interior humidity fall to safe value. It designed ultra-small install size, high efficiency energy-saving, do not need extra heater and fan wiring. And comes with the data acquisition module for remote monitoring, Its an efficient and reliable device to replace the old thermostat and heater / fan combination.
FEATURES
170*100*72mm small size, easy for cabinet inside installation
Condensate water will be drained directly to the outside of the cabinet by the aqueduct
Real-time sampling temperature and humidity, support automatically working mode, do not extra sensor and probe
Build in memory to record settings, can keep original working mode after power recover
Shell and internal components are well isolation design, can work in high humidity and strong electromagnetic field
Optional passive output node
Optional RS485 port
Optional external heater
SET rectifier system use advanced modular design, with multiple rectifier modules together in one 19'' rack box. Makes it flexible to provide enough power supply for Telecom and Power Industrial equipment use.
The power output of rectifier can flexible configuration, depending on equipped different quantities of rectifier modules. It can provides stable DC output to regular load, battery float charging, and batteryequalized charging. Output constant DC charge power, works automatically according to the load demands.
The HOBO Occupancy & Light data logger monitors room occupancy and indoor light changes to identify occupancy patterns and determine energy usage and potential savings. The HOBO UX90-005 Room Occupancy/Light Data Logger is available in a standard 128 KB memory model (UX90-005) capable of 84,650 measurements and an expanded 512KB memory version (UX90-005M) capable of over 346,795 measurements.
DC (AGM Deep Cycle) series is speciallydesigned for frequent cyclic discharge. Byusing strong grids and specially designedactive material, the DC series battery offers30% more cyclic life than the standby series. Itis suitable for UPS, solar & wind energy,telecom system, electric power system,electric vehicles, golf cars, etc.
DG (GEL Deep Cycle)series is pure GEL batterywith 15~20 years floating design life, it is idealfor standby or frequent cyclic dischargeapplications under extreme environments. Byusing strong grids, high purity lead andpatented Gel electrolyte, the DG series offersexcellent recovery after deep discharge underfrequent cyclic discharge use, and can deliver400 cycles at 100% DOD. Suitable for solar,CCTV, marine, RV and deep discharge UPS,communication , and telecommunication , etc.
KP series nickel-cadmium pocket type can bedivided into low rate (KPL), medium rate (KPM)and high rate (KPH) based on their dischargecurrent. It tailored for superior performance athigh temperature, high discharge, fast charge,long-term float or trickle charge.
They have advantage of high power andenergy density, high efficiency ofcharge/discharge,a low cycle life, usually usedfor Railway DC power supply, Wind-energy/Solar systems, Telecom station,Lighting, UPS, Transport Vehicles etc.
Self-healing type low voltage shunt capacitor made of the advanced metalized film is produced strictly in accordance IEC. The device is suitable for low voltage power network to improve power factor reduce reactive loss and better the voltage quality.
Rated voltage (Un) 250V ~ 480V (refer to different mode)
Rated capacitance 5 ~ 40KVar (refer to different mode)
Tolerance -5% ~ +5%
Rated frequency 50Hz / 60 Hz
Over-Voltage Permitted 1.1Un 8h/d
1.3Un 1min daily
Over-Current Permitted 1.6ln
Impact Current: < 500ln
Testing Voltage Between Poles 2.15Un / 10S
Between housing 3000VAC / 60S
Discharge ablity Color ring resistance below 70V within 3 minutes
Ceramic resistor to below 70V in 1 minute
Dielectric Loss < 0.2W/kvar
Standard reference IEC60831-96
UL810-95
Working enviroment Temperature -25C / +50C, Humidity < 90%RH
Altitude < 2000m
Mounting hreaded stud at bottom of can
(max. torque for M16 = 10 Nm)
Mean life expectancy Up to 180 000 hours at temperature class -40C ~ 60C
Max. 15000 switchings per year
LS128 UV power meter can measure the UV energy density, UV irradiance and temperature at the same time. It can be used to:
1. Detect the UV energy density, UV irradiance and temperature of UV curing machine which using UV LED light source.
2. Measure the UV irradiance and temperature of machines which using UV LED light source, such as UV drying machine, exposure machine and printing machine etc.
The Rigol MSO5354 is a 4-channel oscilloscope that has a bandwidth of 350 MHz. Thanks to the exceptionally high sample rate of up to 8 GSa/s and a memory of 25 Mpts/channel, signals can be analysed and processed in great detail. The MSO5354 offers the possibility to measure digital signals in combination with the PLA2216 logic analyser. Furthermore, the oscilloscope can be expanded with various bus trigger and analysis options. Besides the trigger and analysis options, it is also possible to add a power analysis option and a 2-channel function generator to the oscilloscope. Thanks to the 41 built-in waveform parameters, automatic measurements can easily be performed.
The oscilloscope is equipped with a 9" capacitive touch screen, making it easy to operate. With various interfaces like LAN, USB and HDMI it is possible to connect the MSO5354 for example to a PC to transfer the measurement results, or directly to a monitor via the HDMI connection. The Web Remote Control interface allows the user to perform measurements from a distance. For this you only need to enter the oscilloscope's IP address into your browser, no software is required. All this makes the oscilloscope widely applicable for various applications.
SPT Series inverter design for American market, suit for home applicance, office equipment, solar power system, and other equipments.
FEATURES
Pure sine wave output, available for sensitive load.
Accept generator's energy output.
Suit for American 2P3W system, 120/240V.
3-step progressive charging logic, support various battery type in market.
Automatically transfer between battery and AC line modes.
Provide bypass without battery connected.
Optional remote control function.
OPT Series inverter suit for home applicance, office equipment, solar power system, and other equipments.
FEATURES
Pure sine wave output, available for sensitive load.
With grid mode / energy-saving mode / battery mode.
Wide range voltage input, suit for different country city grid
Support various battery type in market.
Automatically transfer between battery and AC line modes.
Optional remote control function.
Blue Jay Technology offers the industry's best selection of isolators. Dozens of models are now available to meet your needs. Select from single and dual-channel models with AC, DC, or loop-powered operation. Signal splitters deliver dual outputs from a single source. And whether you need a unit that sinks or sources current, Blue Jay has the right solution for you.
Optical or galvanic isolation eliminate ground loop errors, reduce noise, and block high voltage transient surges. Our multi-channel modules reduce costs and save space. Models with push-button calibration simplify installation and maintenance tasks. Units with mini USB port preset for 4-20mA input/output required.
Features
·Support universal Input Signal
·Provide 26...18VDC input loop power
·TC/RTD sensor broken alarm
·Low Temp. drift. Auto zero calibrating
·Loop Power current limitation protection (30mA)
·Over-current protection for input current (50mA)
·Current output can be set inverse proportional output
·Programmed by USB or adaptor
·w/o external power supply
·Back board designed with redundant power-supply interfaces
OPT Series Solar inverter (PV inverter) converts the variable DC output of a photovoltaic (PV) solar panel into a utility frequency alternating current (AC) that can be off-grid electrical network. It is a critical balance of systemâ??component in a solar power system, allowing the use of ordinary AC-powered equipment. Suit for home applicance, office equipment, solar power system, and other equipments.
Rated power 1KW / 2KW / 3KW / 4KW / 5KW / 6KW Optional
Rated battery access 12VD / 24VDC / 48VDC / 96VDC Optional
Battery charging ability 30A (default)-C0-C6 can be set
City power-grid Input Voltage range 85-138VAC / 170-275VAC
45 - 65Hz
Voltage Output 110VAC / 220VAC, ±5% (Inverter mode)
50/60Hz±1%
Output wave Pure sine wave
Inverter switching time >10ms (typical load)
Inverter efficiency DC battery inverter > 85% (80% Resistance load)
AC passby > 95%
Output overload 110-120% @ 30s
>160% @ 300ms
Protection feature Battery overvoltage / low voltage, overload, short circuit protection, over temperature protection, Accept custumoerized
Operating temperature 0-40C (Storage -15 - +50C)
CBM-II Series circuit breaker manager (CBM) is an integrated control relay, designed for 3KV to 35KV indoor switchgear, used for replace multiple components in LV compartment, can reduce LV panel space occupation.
On it's panel it provide primary circuit simulation diagram, switch indicator, VCB status & control switch, environment control, high voltage indicator etc. Special sound prompt function can remind staff to operate the switchgear safely.
It can be used in various types of switchgear such as GZS (Centrally Installed Switchgear), Handcart Cabinet, Fixed Cabinets, Ring Main Unit, etc.
DZ47 AC MCB circuit breaker series is used in lighting distribution system or motor distribution system for protecting overload and short-circuit condition. The product is light in weightreliable and excellent in performance.
It has high breaking capacity up to 6kA. Its case and items are adopted with high fire-resistant and shock proof plastics. Mainly used in AC 50/60Hz single-pole 230V or two three four-pole 400V circuit for overload and short circuit protection as well as for on-off switching electric equipment and lighting circuit. The product complies with EN/IEC60898.
Rated current(In) 1A, 2A, 3A, 4A, 6A, 10A, 13A, 16A, 20A,
25A ,32A ,40A, 50A, 63A, 100A Optional
Rate voltage(Un) 230VAC / 415VAC / 400VAC / 415VAC Optional
Breaking capacity 6kA
Rated frequency 50/60Hz
Tripping charateristics BCD
Number of poles 1P, 2P, 3P, 4P, 1P+N, 3P+N Optional
Rated impulse withstand voltage(Uimp) 4kV
Electrical endurance 10000cycles
Mechanical endurance 10000cycles
Terminal Pillar type
CP-M maximun demand consists of 2 bimetallic spirals which are installed working one against each other. Maximun demand indicators are especially suited for the supervision of thermal load of cables and transformers.
The instrument has a sealable resetting knob with which the red drag indicator can be resetted on the position of the meter's movement pointer (Do not turn lower!). Thermal time delay 15 min.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
Accept special customization requirements
IOMS system is a special design isolated signal remote I/O system, it linked a local area network designed to connect controllers to remote I/O chassis and replacement of discrete wirings by fieldbus or industrial Ethernet communication.
MIOS supports up to 31 slots with as many as 128 I/O points in each system. If you need more, you can expand your system with Ethernet router, easily support thousands of I/O points in a single system
FEATURES
Support universal Input Signal
Local area network designed for factory-floor applications
Connects controllers to remote I/O chassis and other intelligent devices
Channel to channel isolated Remote I/O
Built-In Web Server
Dual Channel , Power Hot Swap Supported
Support Multi Communication Protocols
Flexibly Configuration With Sorts of Full Isolated I/O models
MWG1 main module support up to 31units I/O modules
Back board designed with redundant power-supply interfaces
CP-S Synchroscope indicator show the status of phase difference and frequency difference between two power generator or power system. When the voltage and frequencies in between power generator and network is consistency, rotation of LED Roulette will be slowed down until the SYNC LED is on. Both system can be synchronized and connect the generator to the power network.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
CP-W and CP-var analog power meter consists of a moving coil meter with installed transducers which measures the active / reactive power in a sinusoildal or not sinusoidal current circuit and which transformes it into an analogue signal. This is then passed to the moving coil movement.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
Accept special customization requirements
MIOS system is a special design isolated signal remote I/O system, it linked a local area network designed to connect controllers to remote I/O chassis and replacement of discrete wirings by fieldbus or industrial Ethernet communication.
MIOS supports up to 31 slots with as many as 128 I/O points in each system. If you need more, you can expand your system with Ethernet router, easily support thousands of I/O points in a single system
Power Supply 24VDC�±10%
MWG1 â?¦ 1W, other module â?¦ 3W
Analog input Max 60 channels
Digital input Max 60 channels
Analog output Max 60 channels
Digital input Max 60 channels
Communication (RJ45 port) 10m/100m Protocol Modbus TCP, TCP/IP, http
Modbus TCP(client) Max 6 connections
http (client) Max 2 connections
Communication (Modbus Port) Protocol Modbus RTU
Address ID range 1~254
Insulation Resistor >100M�© / 500V between the input / output
Isolation Strength AC1500v 1min between the input / output
Ambient Temp. / Humi. -40 ~ 85 C / â?¦95% RH
Dimensions 113 X 109 X N mm (N â?¦17.5*32)
Terminal Wiring Screw mounting, AWG #26-12
Comm Interface Mini USB
Standard EN61326-2003
LED Indicator Normally lighting indicates power supplied and working normally, blinking indicates digital communication is under way.
DCEM energy meter is an advanced solution for multi-channel DC system. It can visually display voltage, current, power data and energy cumulative data. With a panel keypad, it can set voltage display parameters and the DC shunt parameters.
With RS485 communication interface, DCEM can be connected to the monitoring center. It is a high-performance automatic meter suitable for UPS system detect, Solar energy plant monitor, industrial and mining enterprises, civil construction, building automation etc.
Features
·External Hall sensors for isolation current input, higher safety security
·Max 4 channels energy detect & display.
·Multi-use LCD screen for volt / amp / energy data.
·Built-in isolation circuitry can measure the maximum 1KV voltage signal.
·Provide 4 channels DI port, 2 channel DO for control.
·Provide RS485 port for remote communication.
New 194J series Smart Power Manager is the more powerful meter than 194Y series power analyzer. With higher precision and more measurement parameters.
This meter is the latest series meter developed in 2015 by Blue Jay tech. It is the ideal choice for monitoring and controlling of power distribution systems.
Application
·Provide remote fire alarm.
·Temperature data reading.
·Harmonic analyze.
·Remote data reading.
·Alarm station with voltage-free digital inputs.
Features
·Class 0.2 power and energy
·Current measuring .../5 or .../1 A
·Backlit LCD display
·Expandable input / output modules (up to 3 modules)
·With RS-485 Modbus/RTU Communications
·Measured varies of power parameter. (Max demand/unbanlance/crest factor/K factor...)
·Optional 2 channel Digital Input (DI) and 3 channel Digital Output (DO)
·Record and read multi- tariffs ratio, Up to 3 months
·Provide max 50 lists SOE record function
·ITF Technology: galvanic insulation protection inputs outputs
·Universal series power supply (85-265VAC/DC)
Three phase electrical network power quality detection device, provide energy consumption and generate; THD (Total Harmonic Distortion); Harmonic individual data reading.
Build-in 4 tariffs energy logger function, with onboard memory can record last three month energy data, free to set max 12 segment record period, can be use as a commercial billing unit.
Application
·Applied to the control of general switch boards and low, medium and high voltage connection points.
·Harmonic analyze.
·Remote data reading.
·Alarm station with voltage-free digital inputs.
Features
·Class 0.5S power and energy
·Current measuring .../5 or .../1 A
·Backlit LCD display
·Expandable input / output modules (up to 3 modules)
·With RJ45 Ethernet port support Modbus-TCP Communications
·With 2 channel Pulse Output (PO) for active energy&reactive energy counting
·Optional 1 channel Analog Output (AO)
·Optional 4 channel Digital Input (DI) and 2 channel Digital Output (DO)
·Record and read multi- tariffs ratio, Up to 3 months
·ITF Technology: galvanic insulation protection inputs outputs
·Universal series power supply (85-265VAC/DC)
BJ-192/193 series especially developed for indication and supervision of the three-phase circuit, replaces an analogical display meter, reducing installation manpower and optimizing the used one of spaces in the panel.
Ideal for protection of single phase and three-phase networks, it is monitored and generally to own alarm superior and inferior. Protection of the parameters of programming by password.
Title goes here.
·Class 0.5(192 series)/0.5S(193 series) electrical parameter measurement
·Current measuring .../5 or .../1 A
·Measurement function cover:
Current, Voltage, total three-phase power, power factor, frequency
·RJ45 Ethernet MODBUS-TCP Communications
·Expandable input / output modules (1 modules)
·ITF Technology: galvanic insulation protection inputs outputs
·Large character LED Screen display
·Optional various install sizes
CP-C moving coil panel meter with sprung toe bearing which is insensitive to external magnetic fields. The movable organs of the movements are stored in sprung jewels in order to protect them against crushes and vibrations. These instruments only measure DC current or DC voltage.
By using core magnets of high quality the moving coil instruments have a almost linear scale course. Due to their low consumption they are especially suited for the application with shunts, impulse transmitters, thermo couples and for the connection to our electronic transducers. The instruments can be delivered for direct connection up to 100 A with a built-in shunt.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
Accept special customization requirements
Clamp on AC current measurement up to 200 A.
The CMP-200 digital clamp meter is designed for clamp measurements of AC leakage current.
Clamp on AC Current CMP-200 Features
high resolution (0,1 mA),
three measuring ranges: 200 mA, 2 A, 200 A.
display LCD 3�½ digit (max 1999),
white LED backlight,
sinternal diameter clamp approx. 30 mm (1,2â?³),
DATA HOLD function, for holding measured values.
MAX function,
AUTO-OFF function,
double molded casing.
Available on back-order
Modular DIN Rail Products offer a wide range of functions to be integrated in electrical installations with significant benefits for the user. It is designed for high level performance and are safe and fast to install. Blue Jay have a complete range of DIN-mounted electricity meters for different applications, together with a wide range of communication options. The meters are quick and easy to install due to their DIN-rail mounting.
It is highly accurate, durable, reliable, lower power consumptive, without reversion, creep proof, anti-tanmpering and bilateral recoring with strong overloading capability. It conforms to the related Chinese requirement of GB/T17215.321-2008 and International requirement IEC62053-21 also pass EMC and LVD.
Real-time measurement: voltage, current, power, power factor, frequency, Time-of-use metering of forward and reverse active energy, four-quadrant reactive energy;
Maximum 4 tariffs; with 1 active pulse output;
Automatic settlement function (with a storage of 12 months history records);
Optional Event logging function (power on, power down, zero clearing, demand clearing, programming, timing events);
Optional 2 channels switching value inputs, 1 electromagnetic relay outputs;
Optional 1 channel 12V, 50 mA DC power supply output;
Voltage and current ratio range: 0.0000~9999.9999;
Abundant programmable alarm outputs;
RS-485 supporting Modbus RTU protocol and DL/T645 protocol, self-adaptive;
Indication prompts for voltage broken phase, inverse phase sequence, communication and other status;
Configurable cyclic display items;
Completely enclosed design, dust proof and antifogging.
Interface electrical performance:
Optocoupler relay output interface: AC/DC 250V,100mA
Switching value input interface: Conductor Resistance 1.2KΩ
Transmitter output interface
The 19D-301 three-phase DIN-rail energy meter is an intelligent device for medium and low voltage systems (6-35KV and 0.4KV). It integrates data collection and control functions, provide LCD display show three-phase AC power measurement and calculation, consumption energy value. In addition, 19D-301 also provide optional function, user can choose multi-tariff record, Maximum Demand record, relay alarm output(1 channel) for different site condition. RS485 port support MODBUS-RTU or DL/T645-2007 protocol (can be customized).
features:
1.- Central display area: mainly displays measurement data.
Energy, current, voltage, power, power factor, frequency, timer (depends one different sub-model, display value may parts of above parameter).
2.- Four LED indicators: Show meter condition (accept customized).
3.- Four keys button: for user set operation.
CA-212 has been designed to ensure high accuracy in power factor regulation and excellent utilization of capacitor banks and relays in three phase 3 wire electrical grid common range for all network voltages from 100V to 440V system reactive power compensation front panel is equipped with a 3-digits 7 segments display to show the present value of power factor voltage and line current.
Max 12 steps relay output for contactor easy commissioning optional LCD display screen(provide power monitor function and CT ratio setting).
FEATURES
I / U / COS measurement
Three digital LED display
Max 12 control steps (default 6 steps)
Used in three-phase balance gird
Self-powered from bus line
CB-212 is advance three phase 3 wire APFC display provide user-friendly interface and ease of access to parameters for manual setting built-in power analyzer allowing the instantaneous display of any electrical parameter (voltage current reactive power harmonics etc. With THD protection function not affected by the harmonics can protect capacitor from harmonic interference.
Max 12 step control 5A/250V relay output or 12VDC output. Optional RS-485 communication port easy for user connect to PLC and build SCADA system. Higher measurement accuracy(0.5) and system stability it is cost effective ideal for OEMs and panel builders solution.
FEATURES
I / U / KW / KVAR / HZ / COS measurement and display
93*70 LCD display
Anti-harmonic design
Max 12 steps capacitor control
CD-212 is ready for operation with its preset functions immediately after installation without any modifications or adjustments. With smart switching control identifies the power of the connected capacitor stages and connects or disconnects them in an optimized manner as required by the actual mains conditions. This guarantees that optimum power factor correction is achieved with the minimum number of switching operations.
Dynamic compensation response time less than20ms work with static contactor provide zero-crossing switching and harmonic protect function Suitable for welding steel rolling machinery cranes oil field pumping units wind power generation piling machines and other varies equipment with large instant impact system. With RS485 communication port can control extra 3 sets CD-212 build Max 48 step control.
FEATURES
Automatic detect electrical network system status, do not need special configuration
Large size TFT LCD display, one screen can show more info than segment LCD screen
Various automatic protection functions can make sure capacitor bank long term working
With basic electrical parameter measurement and display (I / U / KW / KVAR / KVA / HZ / COS)
Provide power quality statu display (Current & Voltage wavefrom and 2-31th Harmonic)
Record past 4 days site Power factor trend, display in visualization graph
194Q is a high-end multifunction power analyzer manufactured by Blue Jay. higher measurement accuracy and powerful functions. With its four direct access keys and TFT displays friendly full text interface helps user operate device more easy in 3P3W or 3P4W LV installation. All monitored data is available via a digital RS485 communication port running Modbus Protocol.
It can be used as a data gathering device for an intelligent Power Distribution System or Plant Automation System. Provide Harmonic measurement with multi-tariff record user can easy establish accounting standards for different time. Max 52th harmonic individual monitor let user clear grasp of the present electrical grid quality.
CP-PF series meter using on single phase or 3- phase system measure cos Ï?i, has a moving coil meter movement that shows by an electronic circuit the phase shift between voltage and current (cos. Ï?). Scales are available between 90° and 360° phase shift, as well as capacitive and inductive.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
Accept special customization requirements
CP-W and CP-var analog power meter consists of a moving coil meter with installed transducers which measures the active / reactive power in a sinusoildal or not sinusoidal current circuit and which transformes it into an analogue signal. This is then passed to the moving coil movement.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
Accept special customization requirements
MODELS
Ordering info
Measurement range (Include CT/VT ratio)
Overload (Amp/voltage reading)
Accuracy class
Operation frequency
Marine use or not
BJ194E-9S4, with its four direct access keys and LED displays, helps you use all the parameters in 3P3W or 3P4W LV installation.
These parameters can be centralized on a PC or PLC through an RS 235 link using MODBUS protocol. The casing is designed so that the installer can easily fit the meter to the door of a cabinet.
Applications
1. Metering of distribution feeders, transformers, generators, capacitor banks and motors
2. Medium and low voltage systems
3. Commercial, industrial, utility
Features
1.Class 0.2 or 0.5 power and energy
2.Current measuring .../5 or .../1 A
3.Option RS-232 Modbus/RTU Communications
4.Expandable input / output modules (up to 3 modules)
5.ITF Technology: galvanic insulation protection inputs outputs
6.Universal series power supply
Modular DIN Rail Products offer a wide range of functions to be integrated in electrical installations with significant benefits for the user. It is designed for high level performance and are safe and fast to install. Blue Jay have a complete range of DIN-mounted electricity meters for different applications, together with a wide range of communication options. The meters are quick and easy to install due to their DIN-rail mounting.
It is highly accurate, durable, reliable, lower power consumptive, without reversion, creep proof, anti-tanmpering and bilateral recoring with strong overloading capability. It conforms to the related Chinese requirement of GB/T17215.321-2008 and International requirement IEC62053-21 also pass EMC and LVD.
Real-time measurement: voltage, current, power, power factor, frequency, Time-of-use metering of forward and reverse active energy, four-quadrant reactive energy;
Maximum 4 tariffs; with 1 active pulse output;
Automatic settlement function (with a storage of 12 months history records);
Optional Event logging function (power on, power down, zero clearing, demand clearing, programming, timing events);
Optional 2 channels switching value inputs, 1 electromagnetic relay outputs;
Optional 1 channel 12V, 50 mA DC power supply output;
Voltage and current ratio range: 0.0000~9999.9999;
Abundant programmable alarm outputs;
RS-485 supporting Modbus RTU protocol and DL/T645 protocol, self-adaptive;
Indication prompts for voltage broken phase, inverse phase sequence, communication and other status;
Configurable cyclic display items;
Completely enclosed design, dust proof and antifogging.
19D-201 meter is suit for for single-phase measurement, use scenarios such as residential, public facilities, and industrial use. 19D-201 can measure and display various important power parameters, optional communication ports support remote reading and monitoring. Bi-direction metering makes 19D-201 is an excellent choice for solar energy industry.
features:
-. Detect active/reactive energy, power, frequency, Max demand, voltage, Current and other important power parameters in one screen
-. Provide energy import and export measurement (IMP & EXP)
-. High light white backlit LCD screen
-. Energy pulse output
-. RS485 Modbus communication (optional)
-. Standard 35mm din rail mounting
-. Maximum 100A current access
-. Accuracy: Class 1.0s
The MCM400 main for Non - industrial users sub-metering, use ../100mA or 0.333mV CT, split core design easy for install, Din-rail mounting for every style of electrical panel in build. The unit performs real-time metering, measures energy consumption, multi-tariff time-of-use (TOU) and monitors power quality max 4 channels circuit for three phase circuits, with LCD screen and keypad for easy for configuration. RS485 port can send out collected value to remote host.
Enable reliable monitoring of building electrical loads with a low installation cost-per-point by combining sub-metering. It is ideal for multi-tenant or departmental metering applications within office towers, condominiums, apartment buildings, shopping centers and other multi-user environments.
Features
·Class 0.5 basic parameter and class 1 for active energy
·4 channels three phase metering
·Current measuring .../1A or .../100mA (optional 333mV)
·Standard 35mm - 4 module DIN rail mounting
·Provide RS-485 MODBUS-RTU Communications
·Build in LCD screen, keypad for configuration
·Optional TOU record for each monitor channel
·Accept customization design
BJ-192/193 series especially developed for indication and supervision of the three-phase circuit, replaces an analogical display meter, reducing installation manpower and optimizing the used one of spaces in the panel.
Ideal for protection of single phase and three-phase networks, it is monitored and generally to own alarm superior and inferior. Protection of the parameters of programming by password.
Features:
·Class 0.5(192 series)/0.5S(193 series) electrical parameter measurement
·Current measuring .../5 or .../1 A
·Measurement function cover:
Current, Voltage, total three-phase power, power factor, frequency
·RS-485 MODBUS-RTU Communications
·Expandable input / output modules (1 modules)
·ITF Technology: galvanic insulation protection inputs outputs
·Large character LED Screen display
·Optional various install sizes
BJ-192/193 series especially developed for indication and supervision of the three-phase circuit, replaces an analogical display meter, reducing installation manpower and optimizing the used one of spaces in the panel.
Ideal for protection of single phase and three-phase networks, it is monitored and generally to own alarm superior and inferior. Protection of the parameters of programming by password.
Features
·Class 0.5(192 series)/0.5S(193 series) electrical parameter measurement
·Current measuring .../5 or .../1 A
·Measurement function cover:
Current, Voltage, total three-phase power, power factor, frequency
·RS-485 MODBUS-RTU Communications
·Expandable input / output modules (1 modules)
·ITF Technology: galvanic insulation protection inputs outputs
·Large character LED Screen display
·Optional various install sizes
Accuracy Measurement :Current Class:0.5
Input Measurement:
Wiring: 3-phase 4-wire
Ratio value: AC 1A AC5A
Overload: Sustained: 1.2times; Instantaneous:10times/5s
Power consumption:
Especially developed for indication and supervision of the low-medium voltage three phase electrical network measurement also can be used in DC circuit. It can replaces other analogical panel meter reducing installation manpower and optimizing the used one of spaces in the panel.
Features:
·Class 0.5(192 series)/0.5S(193 series) electrical parameter measurement
·Current measuring .../5 or .../1 A
·Measurement function cover:
Current, Voltage, total three-phase power, power factor, frequency
·RS-485 MODBUS-RTU Communications
·Expandable input / output modules (1 modules)
·ITF Technology: galvanic insulation protection inputs outputs
·Large character LED Screen display
·Optional various install sizes
KLY meters are direct acting analog electrical measuring instruments. They are mainly used on the distribution, control panel of power plant and other different apparatus to measure current, voltage, frequency, power, power factor, synchroscopes. Phase sequence and other non-electric values
The digital meters measure and display the current, voltage, frequency, power, power factor in electric power network and automation control system
Operating Temperature
KLY Series:-25C~+55C
CP Series:-20C~+40C
Storage Temperature
-40C~+70C
CE-D-type three-phase AC intelligent digital display is a programmable function, automatic measurement, digital display, the cumulative power, the standard analog, switch, RS485 output and other functions of the integrated power parameter detection instruments. With high precision, good electromagnetic compatibility, good looks and so on. Can be set according to demand voltage, current, power, power factor and any one of the corresponding standard analog output; any set voltage, current limit, hysteresis, upper limit alarm or lower limit alarm and other parameters; Free to set the communication address (0-255), display ratio and so on.
Accuracy class: 0.5, 0.2 (current, voltage)
The maximum display: 9999
Maximum resolution: Voltage: 0.1V Current: 0.001A
Input: 500V * 5A
Analog output: 0-5V 4-20mA
Communication output: RS485 (baud rate: 9600bps; data format; start bit 1, data bit 8, stop bit 1, no parity)
Switch output: a group of relay contact output, contact capacity 5A / 250VAC
Function settings:
switch control value, back to the difference, the working mode;
analog output mode and input mode;
the address;
display variable ratio;
screen display parameters of the switch.
Auxiliary power: 85 ~ 265V
Power consumption: â?¤ 4.5VA
Isolation voltage: power supply / input / output between â?¥ DC2.5KV / min.1mA
Pulse group interference: 1.6KV
Power against lightning surge: 4KV
Shell material: ordinary plastic
Face plate installation, behind the wiring
Dimensions: 96 Ã? 96 Ã? 110mm
Installation hole size: 91 Ã? 91mm
CP-PF series meter using on single phase or 3- phase system measure cos Ï?i, has a moving coil meter movement that shows by an electronic circuit the phase shift between voltage and current (cos. Ï?). Scales are available between 90° and 360° phase shift, as well as capacitive and inductive.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
Accept special customization requirements
M-4673 mini digital leakage current clamp meter features high reliability, safety, precision and compact design with 1mA resolution. AC/DC Current range of 100A; particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is T-RMS. Whole range overload protection, reliable measurement accuracy and unique design makes it an outstanding new generation electrician/electric power measurement instrument.
This electrical energy meter (kWh) phase DIN rail is a new generation of single-phase electronic energy meters, using techniques microelectronic circuits high integration (LSI), digital techniques and advanced techniques CMS. The meter meets the technical requirements of class 1, class 2 and IEC62052-11, IEC62053-21. It is used to measure active energy consumption accurately and directly from the ac phase (50/60 Hz).
The 149-10A is a digital voltmeter that can measure high voltages up to a10kV AC and DC at high accuracy. Its high input impedance (1000M ohm) make it suitable for measurement of high impedance voltage circuits. Since it has a high accuracy despite its small size and light weight, it can also be easily used as a portable calibrator.
MCM1000 series meter be designed for Industrial or commercial circuits sub-metering project. It's integrate 6pcs three phase energy meter(MCM1300) or 18pcs single phase energy meter(MCM1100). Metering operation processing by different MCU, provide high accuracy billing performerance, can beused as commerical & industry energy metering device.
The compact design and non-display design can maximum reduce the hardware investment of electrical management or building energy metering project.
CP-S Synchroscope meter (analog synchroscope) shows the status of phase difference and frequency difference between two power generators or power systems. When the voltage and frequencies in between the power generator and network are consistent, the rotation of LED Roulette will be slowed down until the SYNC LED is on. Both systems can be synchronized and connect the generator to the power network.
Blue Jay Technology offers the industry's best selection of isolators. Dozens of models are now available to meet your needs. Select from single and dual-channel models with AC, DC, or loop-powered operation. Signal splitters deliver dual outputs from a single source. And whether you need a unit that sinks or sources current, Blue Jay has the right solution for you.
Optical or galvanic isolation eliminate ground loop errors, reduce noise, and block high voltage transient surges. Our multi-channel modules reduce costs and save space. Models with push-button calibration simplify installation and maintenance tasks. Units with mini USB port preset for 4-20mA input/output required.
Features
·Support universal Input Signal
·Provide 26...18VDC input loop power
·TC/RTD sensor broken alarm
·Low Temp. drift. Auto zero calibrating
·Loop Power current limitation protection (30mA)
·Over-current protection for input current (50mA)
·Current output can be set inverse proportional output
·Programmed by USB or adaptor
·w/o external power supply
·Back board designed with redundant power-supply interfaces
ZJJ DC insulation monitoring relay monitorsthe insulation of the DC bus, and it sendsalarm signal when the bus-to-groundinsulation drops to a certain value,also it ispanel mounted type,and the relay has a high-sensitivity grounding resistance monitoringand display circuit, it is great significance forthe safe operation of the DC system.
Monitoring of the DC circuit bus barinsulation resistance RF to LCD screen display resistance value.
Bridge balance method for resistancemeasurement.
Adjustable response value ranges of 0-100k�©.
Smaller short-circuit grounding current forsafe operation.
AFR arc flash protective relay is a costeffective solution that reduces arc-fault damage by detecting the light from an arc flash and rapidly tripping in low-voltage (LV) and medium-voltage (MV) electrical networks. three remote light sensors can be connected to one relay.
It used to limits damages to equipment, improve safety, avoid and protect personnel injuries. It's also can be used as a stand-alone arc protection relay or applied in more complex switchgear layouts.
Amprobe AT-6020 wire tracer is a new and revolutionary instrument, which traces energized and de-energized wires, as well as identifies breakers and fuses with extreme accuracy. Amprobe AT-6020 uses four tracing modes: quick scan wire tracing, precision wire tracing, breaker identification and non-contact voltage detection.
Key Features:
Quick Scan Wire Tracing for fast wire detection from a longer distance
Precision Wire Tracing for accurate wire or fault location behind wall, floors and ceilings
Breaker Identification with automatic sensitivity adjustment for easy location
Non-Contact Voltage Detection to identify energized circuits
"Telemecanique Inductive Proximity Sensors OsiSense XS series (extended sensing range) allow you to detect all types of objects in all applications providing high detection performance for metal objects. This inductive sensor range with industry recognised high performing technology provide non-contact detection of material up to 20 mm. Inductive proximity sensors are available in flush and non-flush models (shielded and non-shielded).
OsiSense inductive proximity sensors are purely for detecting any metal objects up to 60 mm and include an oscillator with windings (an alternating magnetic field is generated in front) making up the sensing phase."
Blue Jay Technology offers the industry's best selection of isolators. Dozens of models are now available to meet your needs. Select from single and dual-channel models with AC, DC, or loop-powered operation. Signal splitters deliver dual outputs from a single source. And whether you need a unit that sinks or sources current, Blue Jay has the right solution for you.
Optical or galvanic isolation eliminate ground loop errors, reduce noise, and block high voltage transient surges. Our multi-channel modules reduce costs and save space. Models with push-button calibration simplify installation and maintenance tasks. Units with mini USB port preset for 4-20mA input/output required.
Features
·Support universal Input Signal
·Provide 26...18VDC input loop power
·TC/RTD sensor broken alarm
·Low Temp. drift. Auto zero calibrating
·Loop Power current limitation protection (30mA)
·Over-current protection for input current (50mA)
·Current output can be set inverse proportional output
·Programmed by USB or adaptor
·w/o external power supply
·Back board designed with redundant power-supply interfaces
Key-Wound Temperature Chart Recorders are equipped with liquid or air sensors, offer selectable 24-hour or 7-day operation and recording, and have a temperature range of 0�°â??150�°F. MA-80 models are wall-mounted while MA-81 units are portable. No power source or batteries are required for operation. Air sensors have bendable 14-3/8in (365mm) cable and liquid sensors are supplied with 5ft (1.5m) cable. Units include a package of 100 MAA-60 7-Day Charts and a felt-tip pen. Additional 7-Day and 24-Hour Charts for Temperature Recorder, and a package of five MAA-62 Felt-Tip Pens are available separately. Inquire for models with NIST-traceable calibration. Temperature sensors contain mercury and may be restricted for sale in some areas; check local regulations before ordering. Also, inquire for Temperature Recorders in other F or C ranges, and/or electric or battery-operated drives.
"The TandD RTR-574-S Wireless Temperature Humidity Light Data Logger
The RTR-574-S Wireless Temperature Humidity Light Data Logger includes two sensors that simultaneously measure and record illuminance / UV intensity and temperature/humidity. This high accuracy data logger allows for the measuring and recording of the above items in various places such as facilities where people gather, where important documents and fine arts are being stored or displayed, where food and drink are being stored. Also, cumulative illuminance and the cumulative amount of UV light can be easily viewed even without stopping recording."
"Ultrasonic heating and cooling energy meters to measure flow and energy in hydronic heating or refrigerant circuits.
Available as heat, cooling energy, or combined heat/cooling energy meters
Separate acquisition of heating or cooling energy by the combined heat/cooling energy meters, with automatic changeover
Non-wearing due to non-moving parts
Approved in accordance with EN 1434 and MID accuracy class 2
Any mounting position (horizontal or vertical), in return
Measuring range of flow 1:100 as per EN 1434, 1:1,000 total range
Choice of communication modules and power supplies
Upstream or downstream setting paths are not required
Optical interface as per EN 62056-21
Self-diagnostics"
INVONIC H is a modern and precise ultrasonic heat meter with ultrasonic flow sensor, that guarantees high measurement precision with a long term operating life regardless of its mounting position. The ultrasonic heat meter has a modular design, making possible to extend its functionality at any time by installing a communication module, changing the power supply option or replacing different temperature sensors. A robust brass body of flow sensor is available in a version with a threaded or flanged connection and may be used in the pressure scopes PN16 or PN25. The heat meter indications are entirely non-sensitive to external magnetic fields.
This device is designed to monitor AC leakage current, then produce a standard signal such as 4- 20mADC, 0-5VDC and so on. It can be applied to arrester state detection, insulation of some electrical equipments and leakage current detection.
High overload capacity: This device can accept heavy current input which is up to 2000A and work in high voltage environment;
High stability: This device can effectively suppress the interference;
High safety: Great surge protection capacity and 35KV isolation.
Rated input: 0~0.5-100mA AC optional
Output signal: 0-5V;0-20mA;4-20mA optional
Power supply: +12VDC;+15VDC;+24VDC optional
Accuracy: 1%
Output ripple: 2kohm; Current Outputâ?¤250ohm
Temperature drift: â?¤400/ppm
Response time: â?¤300ms
Operating temperature: -20~+70
Quiescent power consumption: 360mW(with +12VDC power)
Window size :Ã?20mm
This is a DC voltage and current transducer. The operating principle is Photoelectric Isolation/Treble isolation. It can measure DC voltage and DC current at the same time, and has two channels of standard signal. The input, output and power supply are isolated from each other. It's featured in high accuracy, high isolation, low drift and so on. This product can be used in railway, industry control, and other fields.
Rated input: 0~1-500V; 0~0.5-5A
Output signal: 0~5V DC (Vz); 0~20mA (Iz); 4~20mA (Iy);0~10V DC (Vd);OC frequency output:(0-5KHz/0-10KHz) optional
Power supply: 12V;15V; 24V; optional
Accuracy: 0.5% optional
Output ripple: 10mV
Isolation: 2500V DC
Humidity: â?¤95%(no dew)
Load resistance: Voltage Output >2kohm; Current Outputâ?¤250ohm
Temperature drift: 500/ppm
Response time: â?¤200ms
Operating temperature:: -10~+60
Quiescent power consumptio:
The one element DC multi-parameter digital transducer is used for measuring DC current, voltage and power parameters.Its inputs are DC current (output of mating transducer) and DC voltage, and its outputs are digital data of the DC current, voltage and power through RS-485 interface. It can be applied to various measuring and controlling systems such as communication, power grid and electrization railway etc.
Parameters
Part numbers: CE-AD11-34MS3-0.5/0~500V 0~5A
Description:Input: 0-500VDC,0-5ADC,Output interface: RS-485.MODBUS protocol,Power supply:24VDC(21~27V),Accuracy:0.5%,Window:none,Case style:S3
Part numbers: CE-AD11B-37MS5-0.5/0~1000V 0~5A
Description:Input: 0-1000VDC,0-5ADC,Output interface: RS-485.MODBUS protocol,Power supply:+9~55V,Accuracy:0.5%,Window:none,Case style:S5
Specifications
Voltage input: 0~25mA~500V DC (MS3)
0~25mA~1000V DC (MS5)
Current input: 0~10mA~5A DC (Output of mating Hall Effect analog current transducer)
Output data: DC Voltage, DC Current, DC Power (product of the voltage and current)
Accuracy: 0.2%
Baud rate: 1200, 2400, 4800, 9600 and 19.2K bps
Refresh period: 100 mS
Input overload: 2 times of full span (1 second, 10 times)
Power supply: +24VDC(MS3)
+9~55V(MS5)
Static power consumption: £500 mW
Operating temperature: 0~50°C
Storage temperature: -55~+85°C
Isolation voltage: >2500V DC
Application:
Digital data acquisition
Automation system integrator
Electrical distribution system
Industrial automation engineering
Process automation system
The CE-IJ03 1 element AC current transducer is designed to measure and monitor average RMS AC current, then produce a standard signal such as 4-20mADC, 0-5VDC and so on.
Rated input: 0-500AAC(average RMS current ; TRMS current optional)
Output signal: 0-5V;0-20mA;4-20mA;1-5V;4-20mA loop powered;0-10V; oc frequency(0-5kHZ,0-10KHZ)
Power supply: +12VDC;+15VDC;+24VDC, self power optional
Accuracy: 0.5% optional
Output ripple: 15mV
Isolation: 2500V DC
Load resistance: Voltage Output >2kohm; Current Output=250ohm
Overload capacity: 20 times or
The Gamma-Scout hand-held radiation detector or geiger counter is a general purpose survey meter for measuring and detecting ionizing radiation. It can detect alpha, beta, gamma and x-ray radiation. The Gamma-Scout radiation detector can be used to:
- Determine the source of radiation leakages
- Monitor ambient radiation anomalies
- Monitor personal cumulative dose exposure
- Detect radioactive elements in metal scrap
- Check rocks from the earth for radioactivity
- Teach or learn about radioactivity
*Accuracy: ±0.1% R.O. (DC / Potentiometer / Resistor / PT-100 / Load Cell)
±0.2% R.O. (AC)
*Measuring AC, DC Voltage / AC, DC Current / Potentiometer / Resistor / PT-100 /
Load Cell)
*Small size, slim type 22.5mm, easily installation
*High stability, non-flammable case (PA66), high safety*Accuracy: ±0.1% R.O. (DC / Potentiometer / Resistor / PT-100 / Load Cell)
±0.2% R.O. (AC)
*Measuring AC, DC Voltage / AC, DC Current / Potentiometer / Resistor / PT-100 /
Load Cell)
*Small size, slim type 22.5mm, easily installation
*High stability, non-flammable case (PA66), high safety
The ZP050 Temperature Transmitter is designed to meet common Single Point measurement application requirements. This transmitter can easily work with a variety of sensors (RTDs and thermocouples) and thermowells. It provided in a head mount configuration suitable for installation in a wide variety of connection heads and housings.
Provide HART protocol, equipped USB mini-USB interface, easy-to-use configuration method from any PC.
Power Supply 12VDC~40VDC
Input Types 4-20mA / 20-4mA;
RTD(PT100,PT200,PT500,PT1000,Cu50);
R(0-400 ,0-4000 );
TC(K,E,S,B,R,J,T,N);
mV(-80-+80mV);
V(0-1V)
Output signal types 4-20mA or 0...1/5V, 0...1/10V
Response Time < 0.4S (0-90%,100%-10%)
Precision ±0.05%
Temp. Drift 0.01% per Celsius
Volt fluctuation influence �±0.005% X span / below V DC
Load Capacity < 700 in 24VDC; (mA output)
< 1060 in 36VDC (Volt output)
Isolation Strength AC1500v 1min between the input / output
IP Ranking Casing/Terminal IP50/IP20
Solar Lightâ??s Model 501 Series Radiometers are rugged meteorological-grade instruments which measure solar radiation outdoors and underwater (up to 16.4 feet / 5 meters maximum depth.) World Class manufacturing practices and NIST traceable calibrations ensure a high degree of reproducibility and comparability from unit to unit. Large networks of these precision devices are relied upon by many of the worldâ??s most prestigious metrological observatories, weather stations, and research agencies worldwide, such as the Australian Radiation Protection and Nuclear Safety Agency (ARPANSA) and the Natural Resource Ecology Laboratory (NREL.) Digital versions are available with Sensor Recorders, and analog versions are available with output voltage which is proportional to the measured UV solar radiation. In addition, all 501s feature controlled internal temperature to ensure the highest levels of accuracy.
Measurement Temperature Range:-50 ,100 (-58F,212F)
Humidity Range:0 - 100% RH
Measurement Temperature Range:-50 ,100 (-58F,212F)
Humidity Range:0 - 100% RH
Accuracy : Temperature:0.3 (32.54F)
Humidity : 3% RH
Power Supply: Power : AC220V
Power Consumption: : ¡Â1VA
Environment Work Condition : :-20,65 (-4F,149¨¬F)
Storage Condition: : -40,85 (-40F,185¨¬F)
Resolution Accuracy:0.1/0.1%RH
Communication:RS485 MODBUS RTU
Display : Programmable 1 Line LED Switch Display
Memory Capacity: Up to 20000 data points
Data Sampling Interval:1s to 9 h (user selectable)
Safe Protection : :
Voltage Tolerance : Input & Power Supply >2 KV
Input & Output > 2 KV
Power Supply & Output >1 KV
insulation : >5 M¥Ø.
SIZE: 89X1.89X3.15 inch
G.W/N.W: 500g/400g per piece
Dimensions: 48X48X80 mm.
BJ-S series Intelligent temperature and humidity controller with completed FUZZY algorithm provides very precise of temperature and humidity monitor. FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows temperature and humidity curve by automatically.
Display unit can show environment humidity as per configure by user. The user also can adjust environment condition very easily.
Accept customerized control logic modify details please contact our sales team.
FEATURES
Digital thermostat with 2 control port for fan & heater
3 digital or 4 digital LED screen for temperature and humidity value
Sensor length max 10meter (default 3meter)
Minimal size 48*48mm panel mounting, optional Din-rail mounting rack
B series temperature and humidity controller with completed FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows temperature curve by automatically. And have an independent humidity input can monitor the environment RH and output control signal. User can adjust temperature value very easily to use dial and a LED indicator to show the relay.
FEATURES
Electromechanical thermostat, max with 2 control port for fan & heater
Dial pad setting temperature / humidity threshold
Sensor length max 10meter (default 3meter)
48*48mm panel mounting size, optional Din-rail mounting rack
Intelligent humidity controller with completed FUZZY algorithm provides very precise of temperature monitor. FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows humidity curve by automatically. Display unit can show environment humidity as per configure by user. The user also can adjust environment condition very easily.
Accept customerized control logic modify details please contact our sales team.
FEATURES
Digital thermostat with 2 control port for fan & heater
4 digital LED screen for temperature and humidity value (optional LCD screen)
Sensor length max 10meter (default 3meter)
72*72mm panel mounting size
BJ-S digital temperature protection relay can replace the traditional bimetallic control switch, design to automatically control the install enclosure inside temperature & humidify variation within a specific range, reliable design can be used in the worst environment for longterm use. It is the ideal product to protect the normal efficient operation of electric equipment and to reduce cost.
With LED / LCD display, and optional RS485 communication port for remote monitoring. Optional customerized control logic design, can be used in other place need of temperature and humidity control.
BJ-S series Intelligent temperature and humidity controller with completed FUZZY algorithm provides very precise of temperature and humidity monitor. FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows temperature and humidity curve by automatically.
Display unit can show environment humidity as per configure by user. The user also can adjust environment condition very easily.
Accept customerized control logic modify details please contact our sales team.
B series temperature and humidity controller with completed FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows temperature curve by automatically. And have an independent humidity input can monitor the environment RH and output control signal. User can adjust temperature value very easily to use dial and a LED indicator to show the relay.
-. Electromechanical thermostat, max with 2 control port for fan & heater
-. Dial pad setting temperature / humidity threshold
-. Sensor length max 10meter (default 3meter)
-. 48*48mm panel mounting size, optional Din-rail mounting rack
The ZP series Temperature Transmitter is designed to meet common Single Point measurement application requirements. This transmitter can easily work with a variety of sensors (RTDs and thermocouples) and thermowells. It provided in a head mount configuration suitable for installation in a wide variety of connection heads and housings. A PC-programmable interface is available, providing an easy-to-use configuration method from any PC.
Basic temperature transmitter offers a reliable solution for temperature monitoring points, provides flexible and reliable performance in process environments, Excellent performance with low temperature drift and auto zero calibration, reducing the need for expensive extension wires and multiplexers.
Power Supply 8.5VDC~32VDC
Input Types 4-20mA / 20-4mA;
RTD(PT100,PT200,PT500,PT1000,Cu50);
R(0-400 ,0-4000 );
TC(K,E,S,B,R,J,T,N);
mV(-80-+80mV);
V(0-1V)
Output signal types 4-20mA or 0...1/5V, 0...1/10V
Response Time < 0.4S (0-90%,100%-10%)
Precision �±0.05%
Temp. Drift 0.01% per Celsius
Volt fluctuation influence �±0.005% X span / below V DC
Load Capacity < 700 in 24VDC; (mA output)
< 1060 in 36VDC (Volt output)
Isolation Strength AC1500v 1min between the input / output
IP Ranking Casing/Terminal IP50/IP20
The TPJ-24-G solar radiation recorder is mainly used to monitor and record the total solar radiation inside and outside the greenhouse. It is an important instrument for the research of light energy utilization in the agricultural field. It is widely used in meteorology, agriculture, forestry, scientific research and teaching. The solar radiation recorder supports wireless data transmission, remote real-time viewing, simple operation, convenient management and analysis.
"The boiler tube oxide scale nondestructive tester is a dedicated power plant oxide scale detection instrument developed by our company, which adopts patented technology designed test probe, combined with the universal fluxmeter. On the one hand, it can quickly and effectively detect the status of the power plant boiler stainless steel tube internal oxide scale flaking accumulation, exclude stainless steel tube oxide scale too much leading to pipes brust; on the other hand, it can also provide effective data support for overall oxidation corrosion status of heating surface in the boiler stainless steel tube to help achieve the safety assessment of the boiler.
This instrument is suitable for measuring non-magnetic stainless steel pipe inner layer accumulation rust. It can use a rechargeable battery, without power supply when test, which is suitable for outdoor environment operation. It can be used 4 hours once charge saturation. This product has been used by Hunan Xiangtan Power Generation Company Limited, Wuhan University, Nanyang Henan Yahekou Power Generation Co., Ltd., Anhui Huainan Pingwei power plants and Changsha thermal power plant, received good evaluations.
Concrete structures and components :
the improved DX-201 Fluxmeter and several the test probes matched with pipeline."
"The design of TD8620 hand-held digital Tesla meter follows the IEC-61010-1 safety standard, and conforms to the
national verification regulation of JJG242-1995 Tesla meter.
TD8620 hand-held digital Tesla meter adopts not only the high-sensitivity Hall sensor and high-resolution A / D
conversion chip,but also the popular single-chip computer technology and digital filtering technology .
It has the advantages of high sensitivity,stable reading, low power consumption , and light weight.
The measurement range is 0-2000 Mt, and the basic accuracy is �±1%.
It has the characteristics of automatic zero, automatic measurement range, keeping of maximum / minimum
values, etc."
Blue Jay RCM-IV is a combined monitoring device for earthed power supply systems (TNC-STN-S and TT) residual current. It provide max 16 monitor channels, panel mounting design suit for any electrical cabinet. LED screen display various parameters, easy for site engineer diagnosis and Insulation test.
It can optionally be carried out by selected current transformer or temperature sensor for each channel detect parameter and alarm or trip threshold. Multiple RCM-IV can combination with circuit breaker for build MRCD applications, RS485 port can easy submit data to SCADA systems.
STM wireless temperature monitor can help medium-low voltage switchgear operators and maintenance engineers, to reduce safety risks from sudden temperature increases in switchgear components. It provide 7*24 hours switchgear monitor for critical busbar joints.
Multiple styles of remote sensors node can deal with different electrical contacts, W3000 support max 32 monitoring node for single switchgear. Panel mount HMI unit have acousto-optic alarm and DO port, user can free to build various automatic alarm / control system. Equipped RM485 port can connect existing SCADA system for remote sensering control.
It can protects your electrical assets from costly outages; while increasing safety via remotely monitoring equipment. This also increases asset integrity, and minimizes downtime.
HVD high voltage indicator is adapted for indoor electrical panel, used in MV / HV switchgear. It is connected via internal wiring to capacitive sensors inside the switchgear. Rated voltage 3~40.5kv, operation frequency 50Hz network to display the electrifying situation of the high voltage loop where the device is mounted.
This integrated voltage detecting system is used for continuous operation. The condition "voltage present" is displayed by three LED indicator.
High humidity environment is a big impact factor of power transmission and transformation equipment, it will bring discharge, flashover will eventually cause the switch to trip, even burning down equipment caused a large-scale blackout. Switchgear, electrical cabinet, exchange control cabinets, outdoor terminal boxes, Due to the compact internal equipment installation, wet and condensation will be more serious consequences.
At present, most user choose heating, ventilation and other method to prevent condensation. but in some well sealed cabinet and high temperature environment, traditional heating and exhaust air method is hard to work well.
Blue Jay company developed DH series using semiconductor technology, in a certain place to lead controlled condensation, make the cabinet interior humidity fall to safe value. It designed ultra-small install size, high efficiency energy-saving, do not need extra heater and fan wiring. And comes with the data acquisition module for remote monitoring, It's an efficient and reliable device to replace the old thermostat and heater / fan combination.
DCG series DC insulation monitor is based onRS485 Modbus protocol, suitable for EV DCcharging system, photovoltaic system, energystorage system, DC power grid and other DCsystems under 1000V.
This device has the function of insulationmonitoring start and stop, insulationmonitoring can be real-time monitoring ofpositive and negative poles to the groundinsulation resistance, the monitoring result isnota affected by DC voltage changing, is notaffected by the positive and negative polesinsulation resistance symmetry.
Model DCG-UBC1 DCG-UBCH2
Detect channels Single channel Dual channels
DC voltage range 0~1000V
Power supply 9~30VDC
Insulation resistance range 1K ~10M
Insulation monitoring accuracy 3K +10%(100-300V)
3K +5% (300-1000V)
Measurement accuracy 2V+0.3%
Storage temperature -40 C ~ 125 C
Operating temperature & humidity -40 C ~ 70 C, 85%
Off-line pressure test
ZJB-DT is highly intelligent battery charge and discharge tester. It can be used as the discharge load in the battery off-line state, and realize the constant discharge of the set value by continuously regulating the discharge current. the tester records all valuable and continuous real-time data during the process.
Friendly HMI provide a variety of configuration and data review, user can download record data to USB. PC host operation software can generate the curves and reports needed.
Intelligent SCM ARM control, 7-inch 1024*600 LCD display.
�· Discharge load use PTC ceramic resistor, avoid red heat for a safer discharge process.
�· Remote battery data collector use wireless, multiple band design for 4 device working in one site.
�· Each device support max 25 cell collection boxes, each box connect 12 batteries, total 300 battery cell detecting.
User free to configuration charge/discharge termination threshold.
Provide software export record & curve report for further analysis.
Various alarm function, provide automatic protection in over-temperature/voltage/current status.
With RS485 port for remote control
ZJB-101 online monitoring system consists with battery cell acquisition module and monitoring host device. It provide real-time string voltage, charge / discharge status detect, export current, cell current & voltage, internal resistance etc. It also provide automatic balance function of battery cell, to keep the voltage at a reasonable float charging range, prolong the service life of the battery.
Comm port allow build remote monitor system, provide reliable and effective management method for the battery bank management, reduce risk of power interruption caused by power failure.
The UT521 is an earth-resistance tester. It is essential for various applications to have a good earth connection, for example, to discharge over-voltage or when lightning strikes. Earth testers work with pins that must be inserted into damp soil. In addition, a connecting wire for the measuring object is included, so you can compare it with the earth.
The supplied pins are intended to measure the resistance of the earth to see if it is suitable for inserting an earth pin.
The meter can perform both 2 and 3 wire-resistance measurements, and it is also possible to measure earth-voltage.
"best gauss meter overallSo, Tenmars TM-192 is the best gauss meter overall that we find on the market. It measures with its 3-axis internal orthogonal sensors to ensure accuracy. Also, itâ??s handheld and easy to carry.
To evaluate a wide variety of ELF magnetic fields, regardless of the measuring angle, three internal orthogonal sensors are used for this device. The device is developed to get a more fast, accurate, and clear way for users to calculate the levels of magnetic field energy across power lines, consumer products, and industrial equipment.
The device is a relatively cheap, portable device designed and optimized for measuring magnetic field intensity from 30Hz to 2000Hz at various bandwidths. MicroTesla (mT) or milli Gauss (mG) are the readings display units for this device.
The functionality of data hold (HOLD), maximum hold (MAX), and minimal hold (MIN) is provided in this device. Both Auto Range and P Manual Range mode is provided. Room for data logging of memory size can accommodate 500 data sets. Aside from that, it functions for calendar and time. It also provides a low-level battery indication. The function of the overload display (OL) is given as well."
PDG-1000 provide continuously monitors of partial discharge (PD) in equipment such as transformers, cables in switchgear and rotating machines etc.
It analyzes RF emissions in the HF, VHF and lower UHF ranges by sensors outside the cabinet. HMI unit provides site display of TEV amplitude, ultrasonic amplitude, DO port can drive local alarms, Multi-level alarm notice site engineer. PDG-1000 also can communicate data and notifications across standard RS485 modbus interface to networked supervisory systems.
Rugged, compact design sensor detect TEV and audible ultrasonic.
Non-intrusive and wall-mounted unit design, magnetic adsorption easy installation.
Panel mount HMI unit provide automatic PD data acquisition and analysis.
HMI support max 96pcs sensor, optional wireless and wired(RS485) connection.
Multiple configurable alarms, provide 2*DO NC & NO contact for external alarm trig.
RS 485 MODBUS-RTU easy integration into existing SCADA systems.
PR 260 is modular design motor managerment device, accommodate more I/O modules. Flexible arrangement of motor control modes and state sensing. monitors voltage, current, and temperature to provide a comprehensive package of 22 protective functions. with integrated protection, motor control, metering, and data-logging functions.
This system is typically used to provide protection for three-phase low- and mediumvoltage, mediumto high-horsepower induction motors.
PR 240 is an excellent choice for telemetry applications for Motor monitoring, metering, and control. Its small size, low cost and remote HMI options make the relay a perfect option for power distribution systems for such uses as end-of-line monitoring and power metering.
It offers low-voltage motor protection in virtually all applications, including pumping, air-based, chiller, and bulk-material applications. It can be configured as full range of medium-voltage, three-phase induction and synchronous motors protect relay.
PR200 motor protection relay is an all-in-one solution designed to continuously monitor 3-phase power lines for abnormal conditions. It can use with motors less than 690V/820A. Packed inside a small and economic package you will find a solution designed to save you time and money.
ZJS-102 Insulation monitoring system is a highaccurate and secure online monitoringequipment for DC system insulation. It isdesigned for the measurement of differenttypes of ground fault, insulation decreasing,AC signal interruption, DC signal interruptionand so on.
Monitor detect DC leakage current, mixed withbalanced & unbalanced bridge detectionmode, can display leakage current of each subexport loops. It integrates voltage transientcapture and current synchronous detection,records voltage and current fault curves toachieve instantaneous grounding monitoringand line selection alarm functions.
CP-T series moving iron panel instruments are predominantly used in the usual technical frequency range 15...100 Hz for alternating current and alternating voltage measurements in the ordinary technical frequency range 15...100 Hz.
This instruments practically show independently of the wave form also at high harmonic content - the effective value of the alternating current.
FEATURES
M4 screw connections with clamps make this easier Clamping the connecting wires.
Housing use matiral match UL94V-0 standard
All fastenings suitable for shaking and shock resistance.
Accept special customization requirements
I/O-decentralized automation always includes the replacement of discrete wirings by fieldbus or industrial Ethernet communication.
Remote I/O systems are highly integrated gateways between the field device connection and their communication standard and the discrete I/O area communication standards. Low latency and a high number of I/O connections on modular devices are important criteria.
Blue Jay Technology offers the Universal Remote I/O Link is a local area network designed to connect controllers to remote I/O chassis and a variety of intelligent devices such as operator interfaces and AC or DC drives.
MIOS supports up to 31 slots with as many as 128 I/O points in each system. If you need more, you can expand your system with Ethernet router, easily support thousands of I/O points in a single system
Features
·Support universal Input Signal
·Local area network designed for factory-floor applications
·Connects controllers to remote I/O chassis and other intelligent devices
·Real Full Isolated Remote I/O
·Built-In Web Server
·Dual Channel , Power Hot Swap Supported
·Support Multi Commucation Protocols
·Flexibly Configuration With Sorts of Full Isolated I/O models
·w/o external power supply
·Back board designed with redundant power-supply interfaces
Blue Jay Technology offers the industry's best selection of isolators. Dozens of models are now available to meet your needs. Select from single and dual-channel models with AC, DC, or loop-powered operation. Signal splitters deliver dual outputs from a single source. And whether you need a unit that sinks or sources current, Blue Jay has the right solution for you.
Optical or galvanic isolation eliminate ground loop errors, reduce noise, and block high voltage transient surges. Our multi-channel modules reduce costs and save space. Models with push-button calibration simplify installation and maintenance tasks. Units with mini USB port preset for 4-20mA input/output required.
Features
·Support universal Input Signal
·Provide 26...18VDC input loop power
·TC/RTD sensor broken alarm
·Low Temp. drift. Auto zero calibrating
·Loop Power current limitation protection (30mA)
·Over-current protection for input current (50mA)
·Current output can be set inverse proportional output
·Programmed by USB or adaptor
·w/o external power supply
·Back board designed with redundant power-supply interfaces
