Product Characteristics
Model:Model Y9-38,Y8-39 boiler centrifugal/induced draft fan
Flow:14978-161499m3/min
Shaft power:5.5-160KW
Pressure:400-6679Pa
Port Dia:800-1600A mm
Rotating Speed:730-1450r/min
Product Introduction
Model Y9-38 and Model Y8-39 boiler centrifugal induced draft fan is the latest type of high efficiency and energy saving fan in China.It is widely applicable in the combustion of kinds of coal, and it is designed for industrial boiler (1 ~ 35T/h) with dust elimination device.
The advantage of the fan is high efficiency, wide high-efficiency operation area,low noise,stable, reliable and economical operation.
The medium by the induced draft fan is smoke gas,The maximum conveying temperature should not exceed 250ºC.In front of induced draft fan inlet,the dust elimination device with dust elimination efficiency no less than 85% must be equipped to improve the lifetime of induced draft fan.
Product Characteristics
Model:9-19,9-26
Flow:824-123090m3/h
Pressure:3253-16250Pa
Rotation speed:960-2900r/min
Power:2.2-850KW
Transmission Way:A type(4~6.3)and D type(7.1~16)
The 9-19 centrifugal fan belongs to single suction,could be made two kinds as right-handed and left-handed.Front view is taken from the end of motor,if the impeller turns clockwise,it is called right-handed ventilator,expressed by "Right";if it turns counterclock wise,called left-handed ventilator,expressed by "Left".
The air outlet position is expressed by the air outlet of shell."Clockwise"and "anticlockwise" could be made into totally six angles such as 0°,45°,90°,135°,180°,225°.
Product Characteristics
Model:9-19,9-26
Flow:824-123090m3/h
Pressure:3253-16250Pa
Rotation speed:960-2900r/min
Power:2.2-850KW
Transmission Way:A type(4~6.3)and D type(7.1~16)
The 9-26 centrifugal fan belongs to single suction,could be made two kinds as right-handed and left-handed.Front view is taken from the end of motor,if the impeller turns clockwise,it is called right-handed ventilator,expressed by "Right";if it turns counterclock wise,called left-handed ventilator,expressed by "Left".
The air outlet position is expressed by the air outlet of shell."Clockwise"and "anticlockwise" could be made into totally six angles such as 0°,45°,90°,135°,180°,225°.
2.Product Characteristic
Flow:755-56902m3/min
Power:0.75-37KW
Pressure:294-3667Pa
Rotation speed:400-40000r/min
C4-73 mainly consist of impeller,air inlet,shell,transmission part and motor.
The fan is made in to single suction,three types for the machine code 3.6C,4.5C,5.5C.
The ventilator is made two kinds as left-handed and right-handed.Front view is taken from the end of motor,if the impeller turns clockwise,it is called right-handed vi-lator,expressed by "Right";if it turns counterclock wise,called left-handed ventilator,expressed by "Left".
The air outlet position is expressed by the air outlet of shell.The adjustable range is 0°~225°."Clockwise"and "anticlockwise" could be made into total 6 angles such as 0°,45°,90°,135°,180°,225°.
Model:C4-73,C6-48
Product Characteristic
Model: Model Y5-48 Boiler Centrifugal Induced Draft Fan
Flow:2065-67803m3/min
Shaft power:2.2-110KW
Pressure:742-4483Pa
Port Dia:355-1120A mm
Rotating Speed:1000-3550r/min
Product Introduction
Model Y5-48 boiler centrifugal induced draft fan is designed for industrial boiler (1~20T/h) which burns all kinds of coal and is equipped with dust removal device.It is suitable for anywhere with appropriate intake condition and corresponding performance,but the maximum temperature should not exceed 250ºC.
In front of induced draft fan,it must set a dust elimination device to reduce the dust content of the smoke gas into the fan.According to the general usage of power plant,the dust elimination efficiency is not less than 85%.
In consideration of economy of the fan, triangle belt(C type)transmission is adopted,which can not only meet the requirement of the same tonnage boiler configuration of all kinds of dust remover with different rotating speed of one machine number, but also reduce the fan series and machine number.And It is convenient for user according to the actual situation, to choose different rotating speed to obtain the required and more ideal flow as well as pressure.
3. Product characteristics
Model: 2.8,3.2,3.6,4,4.5,5,6,6.3,7,8,10,12.5,16,20,etc.
Transmission way: 2.8~5(A type);6~12.5(C,D,E type);16~20(B type)
Flow: 565-239654 m3/h
Pressure: 166-3863 Pa
Power: 0.55-220 KW
Rotating speed: 250-2900 r/min
1. Product Introduction
Model 4-72 centrifugal blower is applicable in ventilating and conveying air and other gases that non-flammable, non-explosive, non-volatile, harmless to the human body, non -corrosive to steel in general factory and large buildings indoor. B4-72 centrifugal blower can be used for pumping flammable and volatile gases.F4-72 model is mainly used for conveying corrosive gases.But there must be no any sticky substance in the gases that Model 4-72,B4-72,F4-72 centrifugal blower conveys, and the dust and hard particles contained no more than 150mg/m3. Gas temperature should not exceed 80ºC.
Product Characteristics
Model:CDS series of 3-lobe roots blower
Flow:2.02-7.33m3/min
Shaft power:0.78-11.47KW
Pressure:9.8-68.6kPa
Port Dia:80A mm
Product Introduction
CDS series 3lobe roots blower is our collection for many years of experience in manufacturing blower, using a number of latest research results, professional development of high-tech fan products.The series focused on the current domestic and foreign technical essence of roots blower products, the most efficient use of existing capacity, noise reduction effect of the best special impeller-type line and optimal design of a comprehensive intake and exhaust the whole structure.Using high-precision cnc machining equipment, created painstakingly by professional technical team having many years experience.Therefore the product have high-level technology, high precision, reliable operation, long life. Its technical specifications have reached international advanced level and can replace similar imported products. The products are widely used in environmental water treatment, air transportation, aquaculture, furnace blower, heavy oil burner, gas transportation, electricity, cement, etc.
The main features are high stand-alone pressure, high traffic flow, low noise, little vibration, reliable operation.
Product Introduction
CDS series 3lobe roots blower is our collection for many years of experience in manufacturing blower, using a number of latest research results, professional development of high-tech fan products.The series focused on the current domestic and foreign technical essence of roots blower products, the most efficient use of existing capacity, noise reduction effect of the best special impeller-type line and optimal design of a comprehensive intake and exhaust the whole structure.Using high-precision cnc machining equipment, created painstakingly by professional technical team having many years experience.Therefore the product have high-level technology, high precision, reliable operation, long life. Its technical specifications have reached international advanced level and can replace similar imported products. The products are widely used in environmental water treatment, air transportation, aquaculture, furnace blower, heavy oil burner, gas transportation, electricity, cement, etc.
The main features are high stand-alone pressure, high traffic flow, low noise, little vibration, reliable operation.
Product Characteristics
Model:CDS series of 3-lobe roots blower
Flow:2.02-7.33m3/min
Shaft power:0.78-11.47KW
Pressure:9.8-68.6kPa
Port Dia:80A mm
