1.High quality,high efficiency,98% power factor,three-phase input load balancing,the impact on the user grid greatly reduced,DC input current,smooth,inductance is zero,1000HZ working frequency,time control precision is 1MS;
2.High-strength body structure,good rigidity,direct pressurizing mechanism,linear bearings used in the guiding structure enable good mobility;
3.Adopt high-speed microprocessors,use intelligent optimal calculation method,LCD interface,can save 60sets welding schedule numbers,There are functions of switch display in both Chinese and English,provide external BCD call interface,system fault diagnosis alarm automatically.etc;
4.Specially suitable for welding higher conductive rate of material(such as aluminum,copper,silver and so on) and much more thicker workpiece,widely used in automobile,aerospace and other high request products and industry.
1.Adopted European MOSFET,IGBT solid power module and advanced resonance inverter technology,high efficiency,big output power and energy saving;
2.The digital phase-locked technology achieve frequency trucking automatically,optimization of metal heating process,ensure high efficiency and high speed heating;
3.100% full duty cycle,can work for 24hours continuously.Can control the heating temperature remotely and automatically by extra Infrared Thermometer,improve the heating quality and reduce human operation;
4.Perfect protecting functions,include over-current, over voltage, water shortage, lack of phase and other fault state self-protected and display,also some other necessary functions which will ensure our heaters higher reliability and durability;
5.The time of three stages:Heating,Maintain Temperature,Cooling can be adjusted separately. Furthermore,the function of adjusting the power of Maintain Temperature independently will be effective to control the heating curve and the heating temperature,suitable for workpiece of mass production,repeatability,rapid heating.when used in brazing,adopt combination of rapid heating and maintain temperature,not only heating fast,also solder spread out fully;
6.Easily operate and the output voltage is safe for operator.
1. Hydraulic driven with large pressure, speed uniformity and low noise.
2. Apply to one piece or several pieces metal wires bending, high efficiency and good forming.
3. Apply to single angle bending or continuous automatic bending for polygonal frame through PLC controlled.
4. Quadrilateral length can adjust to any length for bending within machine width.
5. Special design the mold size and control the stroke of bending cylinder to obtain different bending angle.
6. Widely used for wire frame ,angle bending and forming of metal material, such as iron wire(plate), steel wire(plate),aluminum wire(plate),copper wire (plate),etc.
UN3 Series Copper Tube and Aluminum Tube Butt welding Machines specially designed for Copper Tube and Aluminum Tube welding, it can replace the High-voltage Flash Welding Machine and brazing machine with lower and old technology.
The System adopt Programmable Logic Controller(PLC) as the action logic controlling unit; adopt Special Microcomputer Welding Controller as the welding process control unit; adopt the High-quality Aluminum Alloy Cylinder and High-precision Oil Bearings integrated with High-precision Lathe Lever to make precise machinery actions.
It has the reliable welding quality, easy and simple control and adjustment, high productivity, no gas leakage phenomenon, and some other excellence.
The computerized controlling box with secondary constant voltage and constant current, force water cooling system and air storage tank can guarantee the machine produce mass weld in the same shape and quality.
Able to store many different Schedule Numbers according to different size of tubes,easy operation,high efficiency,Widely used in air conditioning ,refrigerator,freezer,refrigerator,compressor,etc.
1. Adopt CNC system, PLC and touch screen control, language switching freely, parameter setting flexibility, high efficiency welding, with counting function.
2. Adopt Pneumatic-hydraulic combination, welding and annealing are both full automatic.
3. Automatic, semi-automatic, manual and other working modes can be chosen.
4. Machine structure design beautiful and reasonable, flexible and adjustable.
5. Accessories or other specification is available according to customers' requirement,Blade Grinding Machine and Cutter are optional.
6. Apply to a variety of sizes and different materials,welding tensile strength,high toughness,speed fast,beautiful weld, good compactness,no blowholes. Much higher than the semi-automatic welding effect and speed.
1.Full digital microcomputer control system,three grades discharge design(Pre-pressing,welding and tempering),equipping functions of Constant Voltage,Constant Current,Constant Heating,Slowly Increasing,Slowly Decreasing,save multi-group Schedule Number,etc.easily meet customers high requirements of welding quality;
2.Integrated high-strength frame Structure,more impact resistant and anti-shock ability under high pressure operation,to achieve more accuracy of welding position,both spot welding and projection welding,reach the largest welding performance;
3.All copper water-cooling transformer,Multi-channel forced water cooling system to ensure the reliability of the machine running for long time;
4.Manufactured in accordance with international ISO Standard and European CE Certificate.
1. There are two types of Welding Power Source : AC Spot Welding or Medium Frequency inverter DC spot welding;
2. The lower welding electrode is designed level flat table:Welding range increased,the welded workpiece stays very flat,not deformed,no mark and smooth under welding point;
3. The up welding electrode is designed as Multi-joint arm, welding easily, without moving work piece, only move the welding gun, can weld any position in the range of the down flat table;
4. At the same time in the 200mm range the lower welding flat table can go up and down freely, by this way it is suitable for welding various shape and size of products;
5. Welding Gun can be made in two types: Vertical Welding or Horizontal Welding,choosed according to different workpiece,More easily operating and freely, safe and reliable.
1.Precision Spot Welding Machine is composed of precision spot welding power source and precision spot welding head, precision spot welding power source also can be used to work with other automation equipment;
2.With two stages current discharge control and current slow rise and slow drop function, can effectively reduce the welding spatter, improve the quality of welding;
3.Equipped microcomputer control system, can be stored 9 sets of welding specification for the user choosing;
4.According to welding requirements, optional single side double point type welding head or a single side single point type welding head;
5.Widely used in sheet metal, wire precision spot welding, such as batteries, fuses, filament, conductive terminals, instrument precision welding .
1.UN2 Series Manual Butt Welding Machine is one kind of manual lever pressuring type of welding,the welding pressure is by way of manual control lever on the workpiece to achieve the butt flash butt welding and resistance butt welding;
2.Mainly used for butt welding variety of steel and Non-ferrous metals,such as low carbon steel, carbon steel, stainless steel and nonferrous metal round wire, flat wire, round steel, flat steel, rebar steel, and so on;
3.Because this kind of butt welding machine no need air compressor, simple operation,easy to move,stable quality,therefore widely used for the field of construction,express way,bridge,steel wire drawing plant,cement prefabricated factory,metal products and so on.Especially suitable for using in the construction field and country side.
Main Features:
Clamp the welding parts by welding electrode firstly without touch, then driving the welding electrode slowly together with a preheat current to flash clean the oxidation and uneven surface to make welding area as hot plasticizing. The temperature of welding area turn to more and more heat and the welding current density increasing together, flash and splash make two touch surface has melted together. Finally perform a fast upsetting force on welding joint to finish welding and breaking current. This type welding joint has high strength without false welding and pores.
Main Applications:
1.All kinds of dinnerware,knives ;
2.Bicycle rim,motorbike rim,car rim,or similar strip rings;
3.Various steel strip,steel rod, construction rebar,round tube and square tube ;
1.AC Resistance Butt Welding is the welding method that the end surfaces of two parts are pressed tightly,and the resistance heat is used to heat up the surfaces to the plasticized status,then the upsetting force quickly press them together more tight again or without applying the upsetting force pressure,just only hold on the welding pressure to complete the welding;
2.Compared to Flash Butt Welding,Resistance Welding is much easily to for worker use and operate,the cost is much lower,welding productivity is also higher;
3.The welded joint is smooth.and the welding burrs are small;
4. The structure is designed compactly which is very easily to be adjusted to weld different parts. The special butt welding control circuits ensure the welding quality;
5. Mainly used for butt welding various metal material with welding section area less than 250mm,such as iron,wires,steel sheet,pipes,etc.
1.Small volume,light weight,machine and welding gun both can move conveniently,adopt 2meters length water-cooling welding cable and hand-held welding gun,the operation is quite flexible,convenient,able to weld inner parts and special parts of workpiece;
2.Can weld many metal and alloy like low carbon steel,weldable steel,stainless steel,iron, copper sheet etc.,welding thickness range is 0.3-3.5mm;
3.Widely used in steel furniture,stainless steel product,security door manufacturing and steel wire mesh reweld for leakage welding etc.
1.There are two standard Types: Transversal Seam Welding Machine and Longitudinal Seam Welding Machine;
2.Also one machine can be used as both transversal seam welding and longitudinal seam welding, only need to change the direction of upper welding wheel and the lower welding head and change the welding arm;
3.Welding wheel adopt three-phase infinitely adjustable-speed drives,convenient to welding speed adjusting,the two welding wheels have the same tangential speed;
4.Adopt adjustable stroke cylinder,to avoid collision damage between upper and lower welding wheel;
5.Driven one head and free the other head;
6.Widely used in hardware, appliances, automotive, manufacturing pots, can, fuel tank, tank producing and other metal manufacturing and processing industries.
1.Automatic TIG (Plasma) Longitudinal Seam Welding Machine is mainly used for the high quality and low distortion automatic longitudinal welding of the metallic cylinders and aligned plates made with stainless steel, iron, aluminum and brass, etc;
2.Adopted keyboard type copper pressing mechanism, to get the regular and stable clamping and cooling effect;
3.Special designed back protective copper block and molding slot, to assure the stable gas shield and achieve double side forming in single side welding;
4.Machine can adopt PLC or Relay integrated control as requirement;
5.Torch moving driven by DC motor , welding speed stepless adjustable;.
6.Apply to cooperate welding with TIG, MIG, MAG and Plasma-Arc welding source.
1.Automatic TIG (Plasma) Circular Seam Welding Machine mainly used for the high quality circular welding of round shape ,oval shape or special shape made with stainless steel, iron, aluminum and brass, etc;
2.According to the shape and size of each welding part, the machine can be designed as Horizontal Type and Vertical Type ;
3.The Workpiece rotation driving mechanism is composed with converter motor, reduction box , and three-jaw clamp, travel steadily with step less adjustable speed;
4.Clamp axle and fixing system pressing down , releasing and retreat , welding torchs action all are driven by air cylinders , furthermore welding torch has been equipped with precision micro-adjustment mechanism to get the best welding position;
5.Control system adopts PLC or Relay integrated control, reliable and simple interface , easily modify and maintenance;
6.Apply to cooperate welding with TIG, MIG, MAG, SAW and Plasma-Arc welding source.
1. Manual feeding type: Manual place the precut wires into mesh mold, start the welding machine and welding a row in turn, then manual push mold to next row for automatic welding until finish a complete mesh;
2. Semiautomatic feeding type: Manual place the precut wires into mesh mold, automatic step feeding to welding position and welding a row automatically, then automatic draw the mesh mold to next welding position and automatic welding until to finish a complete mesh, then mesh mold automatic back to origin and get out the mesh ;
3. Automatic Double Mold Feeding Type: Adopted double layers type or tandem type automatic welding fixtures, and combined advanced PLC , human machine interface and precision servo motor driven system to obtain the continuous feeding and welding automatically.
Machine included double mold for alternating welding, if one performed welding, then another can be placed wires at same time. So the machine can continues working to improve production efficiency;
4. Full automatic feeding type: Equipped automatic hopper for cross wire feeding, line wire automatic feeding as setting length through automatic mesh drawing system .
Widely used for each kinds of fence , hardware mesh, goods shelf, cages, wire frame, steel plate stiffener and others multiple spot welding.
