"The stepper driver has the advantages of miniature size, strong driving force, low heat dissipation, it can provide 0-5A peak current per phase.
Main features of the integrated stepper driver Gecko are as following:
Wide range of 12-36V single voltage supply
Output current 1.5-5A Adjustable phase current by commands
Common cathode signal,Common anode signal,Differential sign,Double pulse,pulse n direction,and other input methods
P2 Max 32VDC, 2A per phase Support full, half, 4/8/16/32/64/128 microstepping resolution
P3 Max 32VDC, 3A per pahse, full, half, 1/4, 1/8 and 1/16 microstepping
P6 Max 6A per phase Support full, half, 4/8/16th microstepping
Support 4/6/8 wires two phase stepping motor
Frequency is the highest 250Khz
TSD, UVLO, OCP protection
Idle current can be adjusted continuously
Support full torque mode for torque enhancement"
"Stepper motor spec:
2 Phase bipolar 4 wires
Rated Voltage 2V DC
Rated Current 1.2A
Phase Resistance: 1.7 Ohm ± 10% (20º C)
Phase inductance: 4.5 mH ± 20% (1kHz 1 V rms)
Holding torque: 0.4 N.m Min.
Shaft diameter: 5mm / 0.188"" (3/16"")
Shaft length: 22mm
Motor depth: 40mm
Controller spec:
Power supply: 12-36VDC
Phase current Max 2.75A
Full, half, 1/4th, 1/8th, 16th and 32th Microstepping"
"PMC006B3 is a kind of miniature integrated stepper motor controller,which can be directly mounted onto Nema17 stepper motor. The microstepping stepper controller can achieve Networking as many as 35 pieces stepper motor n controller controlled by one upper host PC, PLC or Tablet PC. PMC006B3 provides a simple and rich set of control commands,which not only greatly simplifies the complexity of the upper layer control system, but also maximally reserves flexibility of control, and is suitable for all kinds of high precision, wide range of industry using.
Power supply: 12-36VDC
Phase current Max 2.75A
Full, half, 1/4th, 1/8th, 16th and 32th Microstepping"
This is a miniature stepper controller which can be mounted onto NEMA size 17, 23 directly or a mounting plate
Programmable networking stepper controller, it's easy to control at most 120 pieces stepper motors n controllers by one upper host PC, PLC or Tablet PC
Wide supply voltage 12-48VDC
Current per phase 3A or 6A, instruction adjustable
Full step to 256th micro-stepping resolution
Dual full H-bridge with PWM constant current contro
l
"Stepper motor spec:
2 Phase bipolar 4 wires
Rated Voltage 2V DC
Rated Current 1.2A
Phase Resistance: 1.7 Ohm ± 10% (20º C)
Phase inductance: 4.5 mH ± 20% (1kHz 1 V rms)
Holding torque: 0.4 N.m Min.
Shaft diameter: 5mm / 0.188"" (3/16"")
Shaft length: 22mm
Motor depth: 40mm
Controller spec:
Wide supply voltage 12-48VDC
Current per phase 3A or 6A, instruction adjustable
Full step to 256th micro-stepping resolution
Dual full H-bridge with PWM constant current control"
Nema17 40mm Stepper Motor specification same as 17HS3001-20B
Square flange face planetary gearhead Ratio near 14:1
Even though you have Mounting Plate for Nema17 Stepper, this geared stepper with mounting plate upfront is not bad.
The flanged gearhead stepper was designed for cleaning robot.
Nema17 40mm Stepper Motor specification same as 17HS3001-20B
Square flange face planetary gearhead Ratio near 14:1
Even though you have Mounting Plate for Nema17 Stepper, this geared stepper with mounting plate upfront is not bad.
The flanged gearhead stepper was designed for cleaning robot.
