Copper mould tubes for continuous casting machines.
Copper mould tubes are used as a cooling spare part for continuous casting machines.
1. Square copper mould tube
2. Rectangular copper mould tube
3. Round copper mould tube
4. Beam blank copper mould tube
5. Non-standard copper mould tube
Square Mould
50X50~650X650
Rectangular (100~500)X650
Round mould Ф110-Ф1500
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
Copper mould tubes for CCM
Copper mould tubes are used as a cooling spare part for continuous casting machines.
1. Square copper mould tube
2. Rectangular copper mould tube
3. Round copper mould tube
4. Beam blank copper mould tube
5. Non-standard copper mould tube
Square Mould 50X50~650X650
Rectangular (100~500)X650
Round mould Ф110-Ф1500
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
The materials of copper mould tubes should be the ones with good tensile strength, fatigue strength, proper hardness, low elongation and high heat conductivity coefficient. As a result, material like phosphorous deoxidize copper CU-DHP,CUAG0.1, CR-ZR-CU are widely accepted by users of all countries.
Coatings:
Copper has lower hardness which leads to lower anti-abrasive property. Therefore, the area at the lower part of the moulds, where the stress increases drastically due to shells, will be more severely worn. To increase the life time of copper moulds, Uniform mould interior surface plating with suitable hardness is needed. We use hard chrome plating to increase the life of mould tubes. The plating thickness will be controlled in the best range. As for the coating of copper mould plates, based on our years of experience, we are able to provide Cr coating, Ni-Cr coating, Ni-Fe coating and Ni-Co-Cr coating to meet the demand of various customers both at home and abroad.
Notice:
1. Please use the copper mould tubes within one year.
2. Please store the copper mould tubes in someplace dry and well ventilated.
3. Keep the copper mould tubes away from acidic materials, especially the internal coating surface.
4. Polish the external surface of the copper mould tubes with sand paper if oxidized.
5. Pouring the molten steel to the center of the copper mould tubes
6. Avoid internal surface scratch of the moulds caused by manual operation.
Copper mould tubes for continuous casting machines.
Copper mould tubes are used as a cooling spare part for continuous casting machines.
1. Square copper mould tube
2. Rectangular copper mould tube
3. Round copper mould tube
4. Beam blank copper mould tube
5. Non-standard copper mould tube
Square Mould
50X50~650X650
Rectangular (100~500)X650
Round mould Ф110-Ф1500
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
Our major products include series PZ water nozzle, series HPZ air-water spraying nozzle, series GPZ high pressure nozzle, nozzle for painting application, petrochemical industry, paper-making, mechanical lubrication, dust removing, etc. This brochure only covers some of our water nozzles that mainly used in iron &steel plants. If you need more detailed technical data for selecting nozzles, please contact us.
1. Flat nozzle
2. Square nozzle
3. Rectangular nozzle
4. Full cone nozzle
5. Hollow cone nozzle
6. Ellipse nozzle
Oxygen Lance Pipe
1. Plain oxygen lance pipe
2. Ceramic coated oxygen lance pipe
3. Calorized oxygen lance pipe
4. Ceramic coated and calorized oxygen lance pipe
Welded tube and seamless tube is available.
We supply all the types of oxygen lance pipes according to your requirement.
Oxygen Lance is a hollow electric welded tube used in various sizes from 1/8 INCHES to 2 INCHES inside diameter.
Oxygen Lance Pipe comes in a variety of end finishes. End caps are provided to prevent contamination. Oxygen Lancing is a reliable method for tapping heats or for other production operations.
Oxygen Lance Pipe is used to remove the carbon from molten metal. During the steelmaking process, a desired carbon content is attained by injecting oxygen into the molten metal. This process is used in blast furnaces, basic oxygen furnaces and also induction and electric furnaces
Lances are used for opening furnace tap holes, cleaning ladle well blocks, unclogging tundish nozzles, cutting ferrous materials, providing the steel or iron is hot enough to sustain burning, ie cutting skulls, spill clean-up, etc
Oxygen Lancing Pipe
1. Plain oxygen lance pipe
2. Ceramic coated oxygen lance pipe
3. Calorized oxygen lance pipe
4. Ceramic coated and calorized oxygen lance pipe
Welded tube and seamless tube is available.
We supply all the types of oxygen lance pipes according to your requirement.
Oxygen Lance is a hollow electric welded tube used in various sizes from 1/8 INCHES to 2 INCHES inside diameter.
Oxygen Lance Pipe comes in a variety of end finishes. End caps are provided to prevent contamination. Oxygen Lancing is a reliable method for tapping heats or for other production operations.
Oxygen Lance Pipe is used to remove the carbon from molten metal. During the steelmaking process, a desired carbon content is attained by injecting oxygen into the molten metal. This process is used in blast furnaces, basic oxygen furnaces and also induction and electric furnaces
Lances are used for opening furnace tap holes, cleaning ladle well blocks, unclogging tundish nozzles, cutting ferrous materials, providing the steel or iron is hot enough to sustain burning, ie cutting skulls, spill clean-up, etc
Oxygen lance pipe is mainly used for oxygen injection into electric arc furnace. During the steelmaking process, a desired carbon content is attained by injecting oxygen into the molten metals. This process is used in blast furnaces, basic oxygen furnaces. Induction and electric furnaces lance pipes are used for opening furnace tap holes, cleaning ladle well blocks, unclogging tundish nozzles, cutting ferrous materials, etc. In short, oxygen lance pipes also could be used for powder injection, tap hole cleaning and opening nozzles in ladles, tundishes.
Material: welded steel pipe( carbon steel or seamless steel for your choice)
Heat resistance: 1650-1850ºC
Features:
1. Anti-corrosion, anti-sulphurization, anti-oxidation
2. High thermal resistance
3. Longer service life, steel consumption reduced
4. Oxygen/ powder injection efficiency improved
5. Labor intensity reduced (time to replace the pipes reduced)
6. Graphite electrode consumption reduced
7. Melting time reduced
Supply range:
1. Diameter: From 3/8" to1-1/2" for your choice
2. Length: From 2.5 meters to 5.5 meters (customized)
3. Coating: 6.5mm-7.4mm ;7.5-9.5mm (customized)
Oxygen Lance Pipe
1. Plain oxygen lance pipe
2. Ceramic coated oxygen lance pipe
3. Calorized oxygen lance pipe
4. Ceramic coated and calorized oxygen lance pipe
Welded tube and seamless tube is available.
We supply all the types of oxygen lance pipes according to your requirement.
Oxygen Lance is a hollow electric welded tube used in various sizes from 1/8 INCHES to 2 INCHES inside diameter.
Oxygen Lance Pipe comes in a variety of end finishes. End caps are provided to prevent contamination. Oxygen Lancing is a reliable method for tapping heats or for other production operations.
Oxygen Lance Pipe is used to remove the carbon from molten metal. During the steelmaking process, a desired carbon content is attained by injecting oxygen into the molten metal. This process is used in blast furnaces, basic oxygen furnaces and also induction and electric furnaces
Lances are used for opening furnace tap holes, cleaning ladle well blocks, unclogging tundish nozzles, cutting ferrous materials, providing the steel or iron is hot enough to sustain burning, ie cutting skulls, spill clean-up, etc
Thermal Lance
Thermal lance also named thermic lance, oxygen lance, cutting lance or burning bar, etc. It creates a high temperature at least 3600 celcius degree when burned along with oxygen.
The far end of the tube is pre-heated and lit by an oxyacetylene torch. An intense stream of burning steel is produced at the workpiece end and can be used to cut rapidly through thick materials including steel and concrete. The tube is consumed, so every few minutes the operator shuts off the oxygen, discards the remaining stub of a lance tube and starts using a new one.
Application: Fusion cutting ,clean up or boring of all kinds of alloy casting, stainless steel casting, iron and steel casting, non-ferrous casting, concrete, rock, slag, refractory, etc.
Characteristics:
1. High efficiency
2. Easy operation
3. Multi-usages
4. Cost effective
AMK Metallurgical Machinery Group Co., Ltd is located in Wuxi, Jiangsu province. The predecessor of AMK known as BAOLONG which was established on April 27th,1999.AMK is specialized in producing and supplying metallurgical & mechanical equipments and spare parts for steel mill, rolling mill, ferroalloy industry, foundry, mineral processing industry etc. We also provide agency services for domestic and worldwide manufacturers.
1. We supply continuous casting machine and related equipments and spare parts.
2. We supply rolling mill equipments and spare parts
3. We supply industrial furnaces and related spare parts for steelmaking, like EAF, LF, etc
4. We supply metallurgical consumables for iron & steel-making plants
5. We supply graphite products with different grades
6. We supply stainless steel products
A crucible is a container used to hold metal for melting in a furnace and it is needed to withstand the extreme temperatures encountered in melting metals. The crucible material must have a much higher melting point than that of the metal being melted and it must have good strength even when white hot.
Graphite crucible can withstand the high temperature, and has good resistance to chemical erosions and thermal shock. Especially graphite crucible is ideal for the melting of aluminum, copper and other metals.
Crucible has the advantages of high purity, high temperature resistance, with big size ,good thermal insulation, economization on energy ,quality stability etc.
We supply machined graphite spare parts for your choice!
1. Graphite mould
2. Graphite crucible
3. Graphite tube
4. Graphite container
5. Graphite rotor
6. Graphite stopper
7. Graphite ring
Forged steel rolls
To forge ingot castings into work rolls, intermediate rolls and backup rolls with compact structure and homogeneous compositions. As a result, forged rolls have better toughness, more uniform surface hardness and better fatigue resistance than cast rolls with the same type.Forged rolls can be applied to hot rolling and cold rolling.
Application for hot rolling:
Hot-rolling blooming and rough rolling for profile steel
Materials:55Mn2,55Cr,60CrMnMo,60SiMnM,etc.As per buyer's requirements.
Application for cold rolling:
Widely used as work rolls for cold-rolled sheet.
Materials: 9Cr,9Cr2,9CrV,8CrMoV,8Cr2MoV,92Cr2Mo,92Cr2MoV,9Cr3Mo,8Cr3MoV,8Cr5MoV,etc. As per buyer's requirements.
Thermal Lance
Thermal lance also named thermic lance, oxygen lance, cutting lance or burning bar, etc. It creates a high temperature at least 3600 celcius degree when burned along with oxygen.
The far end of the tube is pre-heated and lit by an oxyacetylene torch. An intense stream of burning steel is produced at the workpiece end and can be used to cut rapidly through thick materials including steel and concrete. The tube is consumed, so every few minutes the operator shuts off the oxygen, discards the remaining stub of a lance tube and starts using a new one.
Application: Fusion cutting ,clean up or boring of all kinds of alloy casting, stainless steel casting, iron and steel casting, non-ferrous casting, concrete, rock, slag, refractory, etc.
Characteristics:
1. High efficiency
2. Easy operation
3. Multi-usages
4. Cost effective
AMK Metallurgical Machinery Group Co., Ltd is located in Wuxi, Jiangsu province. The predecessor of AMK known as BAOLONG which was established on April 27th,1999.AMK is specialized in producing and supplying metallurgical & mechanical equipments and spare parts for steel mill, rolling mill, ferroalloy industry, foundry, mineral processing industry etc. We also provide agency services for domestic and worldwide manufacturers.
1. We supply continuous casting machine and related equipments and spare parts.
2. We supply rolling mill equipments and spare parts
3. We supply industrial furnaces and related spare parts for steelmaking, like EAF, LF, etc
4. We supply metallurgical consumables for iron & steel-making plants
5. We supply graphite products with different grades
6. We supply stainless steel products
Copper mould plates and tubes for CCM
Copper mould tubes/plates are used as a cooling spare part for continuous casting machines.
1. Square copper mould tube/plate
2. Rectangular copper mould tube/ plate
3. Round copper mould tube
4. Beam blank copper mould tube
5. Non-standard copper mould tube/plate
Square Mould 50X50~650X650
Rectangular (100~500)X650
Round mould Ф110-Ф1500
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
The materials of copper mould tubes should be the ones with good tensile strength, fatigue strength, proper hardness, low elongation and high heat conductivity coefficient. As a result, material like phosphorous deoxidize copper CU-DHP, CUAG0.1P, CR-ZR-CU are widely accepted by users of all countries.
Coatings:
Copper has lower hardness which leads to lower anti-abrasive property. Therefore, the area at the lower part of the moulds, where the stress increases drastically due to shells, will be more severely worn. To increase the life time of copper moulds, Uniform mould interior surface plating with suitable hardness is needed. We use hard chrome plating to increase the life of mould tubes. The plating thickness will be controlled in the best range. As for the coating of copper mould plates, based on our years of experience, we are able to provide Cr coating, Ni-Cr coating, Ni-Fe coating and Ni-Co-Cr coating to meet the demand of various customers both at home and abroad.
Copper mould tubes for CCM
Copper mould tubes are used as a cooling spare part for continuous casting machines.
1. Square copper mould tube
2. Rectangular copper mould tube
3. Round copper mould tube
4. Beam blank copper mould tube
5. Non-standard copper mould tube
Square Mould 50X50~650X650
Rectangular (100~500)X650
Round mould Ф110-Ф1500
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
The materials of copper mould tubes should be the ones with good tensile strength, fatigue strength, proper hardness, low elongation and high heat conductivity coefficient. As a result, material like phosphorous deoxidize copper CU-DHP,CUAG0.1, CR-ZR-CU are widely accepted by users of all countries.
Coatings:
Copper has lower hardness which leads to lower anti-abrasive property. Therefore, the area at the lower part of the moulds, where the stress increases drastically due to shells, will be more severely worn. To increase the life time of copper moulds, Uniform mould interior surface plating with suitable hardness is needed. We use hard chrome plating to increase the life of mould tubes. The plating thickness will be controlled in the best range. As for the coating of copper mould plates, based on our years of experience, we are able to provide Cr coating, Ni-Cr coating, Ni-Fe coating and Ni-Co-Cr coating to meet the demand of various customers both at home and abroad.
Notice:
1. Please use the copper mould tubes within one year.
2. Please store the copper mould tubes in someplace dry and well ventilated.
3. Keep the copper mould tubes away from acidic materials, especially the internal coating surface.
4. Polish the external surface of the copper mould tubes with sand paper if oxidized.
5. Pouring the molten steel to the center of the copper mould tubes
6. Avoid internal surface scratch of the moulds caused by manual operation.
Copper mould tubes for CCM
Copper mould tubes are used as a cooling spare part for continuous casting machines.
1. Square copper mould tube
2. Rectangular copper mould tube
3. Round copper mould tube
4. Beam blank copper mould tube
5. Non-standard copper mould tube
Square Mould 50X50~650X650
Rectangular (100~500)X650
Round mould Ф110-Ф1500
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
The materials of copper mould tubes should be the ones with good tensile strength, fatigue strength, proper hardness, low elongation and high heat conductivity coefficient. As a result, material like phosphorous deoxidize copper CU-DHP, CUAG0.1P, CR-ZR-CU are widely accepted by users of all countries.
Coatings:
Copper has lower hardness which leads to lower anti-abrasive property. Therefore, the area at the lower part of the moulds, where the stress increases drastically due to shells, will be more severely worn. To increase the life time of copper moulds, Uniform mould interior surface plating with suitable hardness is needed. We use hard chrome plating to increase the life of mould tubes. The plating thickness will be controlled in the best range. As for the coating of copper mould plates, based on our years of experience, we are able to provide Cr coating, Ni-Cr coating, Ni-Fe coating and Ni-Co-Cr coating to meet the demand of various customers both at home and abroad.
Notice:
1. Please use the copper mould tubes within one year.
2. Please store the copper mould tubes in someplace dry and well ventilated.
3. Keep the copper mould tubes away from acidic materials, especially the internal coating surface.
4. Polish the external surface of the copper mould tubes with sand paper if oxidized.
5. Pouring the molten steel to the center of the copper mould tubes
6. Avoid internal surface scratch of the moulds caused by manual operation.
Copper mould tubes for CCM
Copper mould tubes are used as a cooling spare part for continuous casting machines.
1. Square copper mould tube
2. Rectangular copper mould tube
3. Round copper mould tube
4. Beam blank copper mould tube
5. Non-standard copper mould tube
Square Mould
50X50~650X650
Rectangular (100~500)X650
Round mould Ф110-Ф1500
Design with double taper, triple taper
Multi-taper, parabolic taper and various kinds of continuous taper
Non-standard mould
Beam blank mould
The materials of copper mould tubes should be the ones with good tensile strength, fatigue strength, proper hardness, low elongation and high heat conductivity coefficient. As a result, material like phosphorous deoxidize copper CU-DHP,CUAG0.1P, CR-ZR-CU are widely accepted by users of all countries.
Coatings:
Copper has lower hardness which leads to lower anti-abrasive property. Therefore, the area at the lower part of the moulds, where the stress increases drastically due to shells, will be more severely worn. To increase the life time of copper moulds, Uniform mould interior surface plating with suitable hardness is needed. We use hard chrome plating to increase the life of mould tubes. The plating thickness will be controlled in the best range. As for the coating of copper mould plates, based on our years of experience, we are able to provide Cr coating, Ni-Cr coating, Ni-Fe coating and Ni-Co-Cr coating to meet the demand of various customers both at home and abroad.
Oxygen Lance Pipe
1. Plain oxygen lance pipe
2. Ceramic coated oxygen lance pipe
3. Calorized oxygen lance pipe
4. Ceramic coated and calorized oxygen lance pipe
Welded tube and seamless tube is available.
We supply all the types of oxygen lance pipes according to your requirement.
Oxygen Lance is a hollow electric welded tube used in various sizes from 1/8 INCHES to 2 INCHES inside diameter.
Oxygen Lance Pipe comes in a variety of end finishes. End caps are provided to prevent contamination. Oxygen Lancing is a reliable method for tapping heats or for other production operations.
Oxygen Lance Pipe is used to remove the carbon from molten metal. During the steelmaking process, a desired carbon content is attained by injecting oxygen into the molten metal. This process is used in blast furnaces, basic oxygen furnaces and also induction and electric furnaces
Lances are used for opening furnace tap holes, cleaning ladle well blocks, unclogging tundish nozzles, cutting ferrous materials, providing the steel or iron is hot enough to sustain burning, ie cutting skulls, spill clean-up, etc
Oxygen lance pipe is mainly used for oxygen injection into electric arc furnace. During the steelmaking process, a desired carbon content is attained by injecting oxygen into the molten metals. This process is used in blast furnaces, basic oxygen furnaces. Induction and electric furnaces lance pipes are used for opening furnace tap holes, cleaning ladle well blocks, unclogging tundish nozzles, cutting ferrous materials, etc. In short, oxygen lance pipes also could be used for powder injection, tap hole cleaning and opening nozzles in ladles, tundishes.
Material: welded steel pipe( carbon steel or seamless steel for your choice)
Heat resistance: 1650-1850ºC
Features:
1. Anti-corrosion, anti-sulphurization, anti-oxidation
2. High thermal resistance
3. Longer service life, steel consumption reduced
4. Oxygen/ powder injection efficiency improved
5. Labor intensity reduced (time to replace the pipes reduced)
6. Graphite electrode consumption reduced
7. Melting time reduced
Supply range:
1. Diameter: From 3/8" to1-1/2" for your choice
2. Length: From 2.5 meters to 5.5 meters (customized)
3. Coating: 6.5mm-7.4mm ;7.5-9.5mm (customized)
Our major products include series PZ water nozzle, series HPZ air-water spraying nozzle, series GPZ high pressure nozzle, nozzle for painting application, petrochemical industry, paper-making, mechanical lubrication, dust removing, etc. This brochure only covers some of our water nozzles that mainly used in iron &steel plants. If you need more detailed technical data for selecting nozzles, please contact us.
1. Flat nozzle
2. Square nozzle
3. Rectangular nozzle
4. Full cone nozzle
5. Hollow cone nozzle
6. Ellipse nozzle
By cooperating with Chinese domestic leading manufacturers, we're able to supply all kinds of couplings to meet your requirements.
The universal coupling shaft is used to connect driving shaft and driven shaft of two different mechanisms, so that torque could be transferred.
Universal Joint Shaft (Universal Coupling) is used as the main transmission connecting shaft for the main transmission of hot continuous rolling rough mill, large section steel rolling mill, punching machine, medium width plate mill, steckel mill and other heavy machinery.
