KEY FEATURES:
1. High tensile strength
2. Good rebound property
3. Outstanding resistance to ageing
4. Low shrinkage
5. Low yellowing
6. Excellent thermal and cold stability
APPLICATION:
The series are suitable for making silicone kitchenware.
PACKAGING:
It is available in 20kg pails of 200kg drums
TYPICAL PROPERTY:
Appearance: Transparent;
Viscosity (mpas): 650,000~950,000;
Hardness: 20~70 Shore A;
Tensile Strength: 6.5~8.5 MPa;
Tear Strength: 20~35 KN/m;
Elongation at break: 330%~800%;
Linear shrinkage: 0.1%
REMARK:
The product should be closed tightly, protected from light and moisture, the shelf life is 12 months.
These figures are for reference only, please contact us for detail.
20 KG/drum
KEY FEATURES:
1. High transparence
2. High tensile strength
3. Good rebound property
4. Outstanding resistance to ageing
5. Low shrinkage
6. Non-discoloring
7. Excellent thermal and cold stability
APPLICATIONS:
The series are suitable for making baby nipples.
PACKAGING:
It is available in 20kg pails of 200kg drums
TYPICAL PROPERTY:
Appearance: Transparent;
Viscosity (mpas): 650,000~950,000;
Hardness: 20~70 Shore A;
Tensile Strength: 6.5~8.5 MPa;
Tear Strength: 20~35 KN/m;
Elongation at break: 330%~800%;
Linear shrinkage: 0.1%
REMARKS:
The product should be closed tightly, protected from light and moisture, the shelf life is 12 months
These figures are for reference only, please contact us for detail.
20 KG/drum
THE USAGE OF SILICONE FOAMS:
Silicone Foams can be used for a variety of industrial and special effects applications including making foam filled appliances, padding /seat cushioning, orthotics/orthopedics, potting and encapsulation of electrical circuits and vibration dampening.
THE CHARACTERISTIC OF SILICONE FOAMS:
1.Mixed Viscocity
2.Very soft
3.Excellent temperature resistence
IMPROVE SURFACE FINISH AND MINIMIZE VOIDS WITH BACK PRESSURE:
Use a board that will completely cover the mold opening. Using a drill bit, drill 3 holes in the board spaced a few inches / cm apart. Make sure that, when the board is placed over the mold opening, the holes are over the mold cavity and rising foam will be able to make it through. Apply Ease Release 200 thoroughly too both sides of the board and into the drilled holes. Mix and pour foam into mold cavity and place board over mold opening. Hold board firmly in place. As foam rises in the mold cavity, some foam will grow out of the drilled holes. After the foam stops growing, you can let go of the board. Do not demold for at least 20 minutes.
INTRODUCTION OF THE SILICONE RUBBER FOR MAKING PRINTING PAD:
Pad printing silicone rubber is kinds of RTV-2 liquid silicone rubber with excellent fluidity and good operational performance,it includes platinum cure type and tin cure type. Its function is to pick up the image from the steel plate (cliche) and then transfer it to the product of almost any convex , concave, regular ,irregular ,or flat surface.
APPLICATIONS OF THE SILICONE RUBBER FOR MAKING PRINTING PAD:
Pad printing silicone rubber is applicable to produce printing pads / transfer pads, Which is used for printing the irregular patterns on plastic toys, ceramic products,aluminum alloy sheet,electroplating products, trademarks, artworks and stationery etc. The silicone pad is a carrier which transfers the patterns from the steel plate onto the product's surface.
ADVANTAGES OF THE SILICONE RUBBER FOR MAKING PRINTING PAD:
- Thousands of printing times, high quality
- Excellent printing effects
- Excellent resilience
- Without any impurity
- Multiple hardness
MAKING INSTRUCTION OF THE SILICONE RUBBER FOR MAKING PRINTING PAD:
Step 1: Prepare the original molds, make sure your original molds smooth and Clear.
Step 2: Mix part A liquid silicone and silicone oil.
Step 3: Add catalyst (part B) into the mixture and mix them evenly.
20 KG/drum
INTRODUCTION:
It is a hydrophilic addition silicone rubber impression material, it contains two components, Part A is platinum catalyst, and Part B is hydrogen containing polysiloxane. This product comprises liquid material and powder material. The main raw material is a silicone oil, silicone resin, alumina, quartz powder and etc.
COMPOSITION:
Base components 350 g;
Catalyst component 350 g;
A white spoon;
A blue spoon
PHYSICAL PROPERTIES:
Appearance:Catalyst Components(White putty),
Base Components(Blue putty);
Mix ratio: 1:1
Pot life: > 60 seconds
Curing time(37C): < 5 min
Hardness(Shore A): 60
Permanent deformation (%):<0.2
Dimensional stability (%):<0.25
Copy details(|¨¬m): <1.5
Tearing Strength (Mpa):2.0
Temperature stability: 60¡ãC for 1 week
Elongation(%):267
APPLICATION:
It is suitable for the production of precise dental crown, dental fixed bridge, dentures, and articulation registration and takes the mold of ** tissue
USAGE INSTRUCTION:
1. Under the room temperature, take the same amount of base component (blue) and catalyst component (white).
2. Mix the two components together.It is recommended to use the blue spoon to take the base component and white spoon to take catalyst component.
3. Use your fingertips to mix the two components together and knead for at least 30 seconds until they are mixed completely.
4. Close the lid immediately after usage, the cover can not be interchanged.
MAIN FEATURE:
1. Good plasticity, small volume incorporation rate, it needs only 3-5min to vulcanize into elastomer at high temperature, very easy to remove from the mouth after the stamp, and has good chemical stability.
2. High accuracy of mold impression, capability of reproducing the fine structure of the mouth, with good elastic recovery, and good tear strength and dimensional stability, it can provide accurate and reliable morphological basis for clinical dentistry.
3. It has compatibility with almost all model materials, reusable for a period of time and can be sterilized.
PRECAUTIONS:
1. Do not use natural rubber gloves. It is recommended to use disposable polyethylene plastic gloves.
2. The product contains platinum catalyst, sulfur, phosphorus, amine, etc. will slow down or even stop the curing reaction, and thus it must avoid sulfur, phosphorus, amine, acrylic and meth acrylic acid esters and other chemical products in use.
3. Close the lid tightly and immediately after use, keep it in cool place, and be refrigerated in summer.
4. The temperature has a significant impact on the curing time; the curing reaction will slow down at low temperature, and speed up at high temperature curing speed. It should adjust operation rhythm according to the environment and the finger temperature.
5. It is strictly recommended to use the same amount of base and catalyst. Unequal amount will lead to delayed or accelerated cure.
20 KG/drum
DESCRIPTION OF MANUAL MOLD DESIGN MAKING LIQUID SILICONE RUBBER RAW MATERIALS:
This is a kind of room temperature vulcanized silicone rubber in condensation type. It's generally named as two part silicone rubber, Part A is a flowable liquid, part B is the curing agent or catalyst. It¡¡¥s mainly used for mold making.
This Silicone rubber is with good fluidity and moderate hardness which is suitable for middle size product with pattern by pouring operation, especially popular for manufacturer of resin crafts and gypsum decoration. Besides,additive is available for brushing operation. It¡¡¥s one of our best selling silicone!
APPLICATION OF MANUAL MOLD DESIGN MAKING LIQUID SILICONE RUBBER RAW MATERIALS:
This silicone rubber is used for making molds of concrete stone,GRC, gypsum decoration, plaster ornaments, fiberglass products, polyester decoration , unsaturated resin crafts, polyresin crafts, polyurethane, bronze, wax, candle, and similar products .
CHARACTERISTICS OF MANUAL MOLD DESIGN MAKING LIQUID SILICONE RUBBER RAW MATERIALS:
*An exceptional fluidity and good operability, easy to demold
*Moderate hardness
*High tensile and tear strength
*Good flexibility
*Cure at room temperature
*Outstanding bubble releasing
*High duplication times
OPERATION INSTRUCTIONS OF MANUAL MOLD DESIGN MAKING LIQUID SILICONE RUBBER RAW MATERIALS:
Step 1: prepare the original molds
Step 2: Take 100G parts A and add 3G parts B and mix them evenly.
Step 3: Vacuum pumping
Step 4: Pouring casting or Brush operation
(For the detail of operation instructions,please contact us)
SHELF LIFE :
Twelve(12) months when stored under dry and cool place by original package under 25¡æ
ABOUT US:
We are engaged in silicone rubber's R&D since 1996, there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber.
What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us.
20 KG/drum
LIQUID RTV-2 SHOE MOLD SILICONE RUBBER APPLICAITONS:
Shoe mold silicone rubber is mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products,products with non-complex patterns, as well as product models with stable size and non-deformation.
LIQUID RTV-2 SHOE MOLD SILICONE RUBBER FEATURES:
1.Two-component silicone rubber with tin-catalyst
2.Cured under room temperature
3.Low shrinkage
4.Excellent fexibility & easy demould
LIQUID RTV-2 SHOE MOLD SILICONE RUBBER USING INSTRUCTION:
The component A of shoe Mold Silicone Rubber is white flowing liquid and the component B is the curing agent. For example, take silicone rubber of 100g and add 2% curing agent for mixing evenly. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles. After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame.
LIQUID RTV-2 SHOE MOLD SILICONE RUBBER NOTES:
Shoe mold silicone rubber is used for pouring or brushing technique. That is to say, fix the product or sole model to be duplicated onto a plane plate, then enclose the plane frame with wooden plates to prevent the leakage of the silicon , mix the silicone rubber and the curing agent evenly according to the mixing ratio of 100 : 2 and pour them onto the sole model, then brush evenly with a wooden plate or a brush, and fill up the mold frame with gypsum after the silicone rubber is dried.
20 KG/drum
