FeatureApplications
* long life * air purifier
* high sensitivity* air quality monitoring
* automatic calibration * air ventilation system
* comes with temperature & humidity compensation
* low cost
Spec
* module model:Aqm-300c
* sensor:Aqs501 air quality monitoring sensor
* gas detection: ammonia, hydrogen, alcohol, carbon monoxide, methane, propane, gan alkyl, styrene, propylene glycol, phenol, toluene, ethylbenzene, xylene, formaldehyde and other volatile organic gas, such as cigarettes, wood , paper burning smoke.
* physical interface:Xh2.54-4 vertical outlet
* output data:Ttl level¡§built-in 200ohm current limiting resistance
* input voltage:5.0¡¡.2vdc ¡§without voltage reverse polarity protection
* operating current:80ma
* warm-up time:2 minutes
* response time:10 seconds
* recovery time:20 seconds
* operating temperature:-10 --- 40
* operating humidity:95µ¶h
* storage temperature:-20 --- 60
* storage humidity:60µ¶h
* dimension:242015¡§l‡óh
* weight :About 20g
* sensitivity :1ppm hydrogen
* sensitivity reduction:¡¡.2%/year
* life:10 years
Interface definition
1Power supply negative
2Power supply positive
3Output signal a
4Output signal b
Output signal definition
ABPollution degree
LowLow0
LowHigh1
HighLow2
HighHigh3
Remarks¬hèùåê higher the pollution degree no., the worse the air quality.
1. Introduction:
New Air intelligent controller (KF-800F) can monitor real-time indoor temperature, CO2 concentration. Controller output signal can directly control the startup and speed of ventilator. It can be widely used in residential, commercial and industrial applications, and can effectively improve air quality, create a healthy, comfortable, energy-efficient living and working environment.
2. Buttons function
1. button: timing parameter setting
2. button: parameter increase
3. button: parameter reduce
4. button: setting working mode for controller, press this button slightly, the controller will be switched circularly betweenAUTO MANUAL TIMER POWER OFF.
3. Display explana4. Detailed explanation
1. AUTO (auto mode): high speed: CO2 concentration exceeds the setting concentration value of 300ppm; middle speed: CO2 concentration exceeds the setting concentration value of 100ppm; low speed: CO2 concentration exceeds the setting concentration value; stop: CO2 concentration is below the set concentration value.
2. MANUAL: set the ventilator as OFF(stop)LOW(low speed)MED(middle speed)HIG((high speed))by buttons and , and under this mode, the ventilator will run according to the setting, won¬H be affected by CO2 concentration.
3. TIMER (timing mode): run according to set time & speed, can set from Monday to Sunday, 4 periods every day, and 28 periods in total.
4. Automatic mode Cconcentration value setting when the ventilator starts: under the auto mode, press or button for one second, it will appear CO2 concentration setting value and flicker, then press and buttons to change the number (from 350 ¡§C 600ppm). Controller will return to normal working condition and save setting parameter automatically if you won¬H press any buttons more than 10 seconds during the setting process.
5. Timing parameter setting: press button for 2 seconds to enter parameter setting. First enter ¡ãlocal time adjust¡À, press button to switch week, hour and minute, the corresponding parameter will flicker, change the number by and buttons; after finishing adjusting local time, press button to enter the first period hour setting on Monday, press button to switch hour, minute, and ventilator speed, press and buttons to change the number. After finish the setting, press button to enter the second period hour setting on Monday. Repeat above steps to finish all the 28 periods setting. Controller will return to normal working condition and save setting parameter automatically if you won¬H press any buttons more than 10 seconds during the setting process.
6. Backlight: CO2 concentration less than 500ppm (green backlight), 500-799ppm (yellow backlight), higher than 800ppm (red backlight).
1. Introduction:
New Air intelligent controller (KF-800E) can monitor real-time indoor temperature, humidity, VOC concentration. Built-in air quality sensor can monitor ammonia, formaldehyde, benzene, xylene, hydrogen, alcohol, carbon monoxide, methane, propane, Gan alkyl, styrene, propylene glycol, phenol and other Volatile organic compounds as well as wood, paper, cigarette smoke and a dozen combustion gasesController output signal can directly control the startup and speed of ventilator. It can be widely used in residential, commercial and industrial applications, and can effectively improve air quality, create a healthy, comfortable, energy-efficient living and working environment.
2. Monitoring objects
1. Volatile organic compounds (VOC) concentration¡¡100ppm
Real-time monitoring indoor air whether including formaldehyde, benzene, ammonia, hydrogen, alcohol, carbon monoxide, methane, propane, Gan alkyl, styrene, propylene glycol, phenol, toluene, ethylbenzene, xylene and other volatile organic gas, such as cigarettes, wood , paper burning smoke or not.
2. Indoor temperature: 0---- +50
3. Indoor humidity: 5 H----95%RH
3. Function & Feature:
1. Real-time display indoor concentration of volatile organic compoundsVOC)
2. Display the current indoor air pollution levels
3. Real-time display the indoor temperature
4. Real-time display indoor humidity
5. According to temperature, humidity and VOC concentrations, automatically adjust the ventilator operation
6. Display the new air system ventilator statusStop, slow, medium and high speed, working modeManual, automatic, timing
7. Automatic mode±bè ` the intelligent controller detect indoor air quality become worse, the new air system can automatically adjust the ventilator speed
8. Manual mode e can control the startup & speed of ventilator by ¡ãmode button on the controller panel or ¡ãRF remote control
1. Introduction:
New Air intelligent controller (KF-800M) can monitor real-time indoor temperature, CO2 concentration. Controller output signal can directly control the startup and speed of ventilator. It can be widely used in residential, commercial and industrial applications, and can effectively improve air quality, create a healthy, comfortable, energy-efficient living and working environment.
2. Buttons function:
1. button: timing parameter setting
2. button: parameter increase
3. button: parameter reduce
4. button: setting working mode for controller, press this button slightly, the controller will be switched circularly between AUTO MANUAL TIMER POWER OFF.
3. Display explanation:
Time
Indoor temperature CO2 concentration
Heating switch mode
Operating mode
Ventilator status
4. Detailed explanation
1. AUTO (auto mode): high speed: CO2 concentration exceeds the setting concentration value of 300ppm; middle speed: CO2 concentration exceeds the setting concentration value of 100ppm; low speed: CO2 concentration exceeds the setting concentration value; stop: CO2 concentration is below the set concentration value.
2. MANUAL: set the ventilator as OFF(stop)LOW(low speed)MED(middle speed)HIG((high speed))by buttons and , and under this mode, the ventilator will run according to the setting, wonH be affected by CO2 concentration.
3. TIMER (timing mode): run according to set time & speed, can set from Monday to Sunday, 4 periods every day, and 28 periods in total.
4. Automatic mode ¡ìCconcentration value setting when the ventilator starts: under the auto mode, press or button for one second, it will appear CO2 concentration setting value and flicker, then press and buttons to change the number (from 350 ¡ìC 600ppm). Controller will return to normal working condition and save setting parameter automatically if you wonH press any buttons more than 10 seconds during the setting process.
5. Timing parameter setting: press button for 2 seconds to enter parameter setting. First enter šÑ�N’“ã¸šÑ time adjust, press button to switch week, hour and minute, the corresponding parameter will flicker, change the number by and buttons; after finishing adjusting local time, press button to enter the first period hour setting on Monday, press button to switch hour, minute, and ventilator speed, press and buttons to change the number. After finish the setting, press button to enter the second period hour setting on Monday. Repeat above steps to finish all the 28 periods setting. Controller will return to normal working condition and save setting parameter automatically if you wonH press any buttons more than 10 seconds during the setting process.
6. Backlight: CO2 concentration less than 500ppm (green backlight), 500-799ppm (yellow backlight), higher than 800ppm (red backlight).
5. Specification
Product specification:
1.Fashion, colorful, best choice for gift
2.Touch button design, simple and convenient
3.Air quality sensor to real-time monitoring a variety of harmful gases
4.Colorful led lighting can be set at your pleasure
5.Ultra quiet, dc supply & brushless motor
6.Efficient negative oxygen ion generator to remove dust & sterilize, clean air
7.Activated carbon strainer can super absorb harmful gases
8.Home decorative embellishment, night light function
9.The best color alerts and purification partner for harmful gas in the car
10.Shield of polluted air in the office
11.Fashion, colorful, best choice for gift
12.Touch button design, simple and convenient
13.Air quality sensor to real-time monitoring a variety of harmful gases
14.Colorful led lighting can be set at your pleasure
15.Ultra quiet, dc supply & brushless motor
16.Efficient negative oxygen ion generator to remove dust & sterilize, clean air
17.Activated carbon strainer can super absorb harmful gases
18.Home decorative embellishment, night light function
19.The best color alerts and purification partner for harmful gas in the car
20.Shield of polluted air in the office
