D201 is a high capacity, shock resistant, macroporous,Type I ,strongly basic anion exchange resin supplied in the chloride or hydroxide form as moist, tough, uniform, spherical beads. D201 has a high operating capacity, especially on high-FMA feedwaters, as well as a high reversible sorptive capacity for complex organic materials, such as the fulvic and humic acids which occur in many surface water supplies.
It is recommended for use in waters with low silica loads. For high silica
waters, a type 1 anion resin such as Pure D201 is recommended.
Typical physical & Chemical characteristics:
Polymer Matrix Structure: Styrene Crosslinked with DVB
Physical Form and Appearance: Opaque beads
Whole Bead Count: 95% min.
Functional Groups: R-N(CH3)2(C2H4OH)+
Ionic Form ,as shipped: CL
Total Exchange Capacity, CL- form, wet, volumetric
1.2 eq/l min.
Moisture Retention, CL- form: 47-57%
Particle Size Range: +1.2 mm <5%, -0.3 mm <1%
Swelling CL-¡ú OH-: 10% max
Shipping Weight (approx.): 680-730 g/l
PH Range, Stability: 0 - 14.
25L /bag,1000L /big bag with pallet.
MB101 is a high quality resin mixture for direct purification of water. It is suitable for use in regenerable or non-regenerable cartridges and in large ion exchange units. Passage of water at recommended flow rates through the resin as supplied can achieve almost complete reduction of total dissolved solids. The residuals produce average conductivity values of about 0.1 µs cm-1 for a major portion of the service run which may be extended depending upon the final water quality acceptable. Equivalent volumes of ultra pure water may be obtained after regeneration but only if sufficient regenerant quantities are employed to achieve the percentage conversion levels equivalent to those of the "as supplied" resin. Generally acceptable capacity and quality is obtained economically at lower regeneration
Typical physical & Chemical characteristics:
Guaranteed Sales Specification Units OH - Form H + Form
Polymer Matrix Structure - Gel PolyStyrene Crosslinked with DVB
Anion Cation
Functional Group - Quaternary Amine Sulfonic acid
Volume ratio - 60% 40%
Total Exchange Capacity, min. meq/l 1.30 1.9
Water Retention Capacity % 53-60 45-50
Particle Size Distribution - - -
>1.25 mm max. % 5 5
<0.40 mm, max % 2 2
Whole Bead Count, min. % 95 95
Moisture Content as shipped, max - 65%
PH Range, Stability - 0-14
Shipping weight (approx.) - 705-740 g/l
Ionic conversion, min. % 90 99
5L/BAG,25L/CARTON IN VACCUME.
001x7 is a high purity premium grade ,high capacity, gelular, sulfonated, polystyrene cation resin supplied in the sodium or hydrogen form as moist, tough, uniform, spherical beads. 001x7 is intended for use in all water softening, dealkalization, deionization and chemical processing applications.
Typical physical & Chemical characteristics:
Polymer Matrix Structure: Styrene Crosslinked with DVB
Physical Form and Appearance: Clear spherical beads
Whole Bead Count: 97% min.
Functional Groups: R-SO3
Ionic Form ,as shipped: Na
Total Exchange Capacity, Na+ form, wet, volumetric: 1.8 meq/l min.
Moisture Retention, Na+ form : 48-52%
Particle Size Range: 0.3-1.20mm
Less than 0.3mm1.0 %max
Swelling Na+¡÷ H+: 10% max.
Ca2+¡÷Na+: 5% max.
Shipping Weight (approx.): 800 g/l
Specific Gravity, moist Na+ Form: 1.29
PH Range, Stability: 0 - 14.
25L /bag,1000L /big bag with pallet.
D301 is a very high capacity, bead form, weak base, macroporous type, anion resin made by epoxy polyamine condensation. It is a spherical bead form resin(unlike other granular formulations) suitable for use in high flowrate applications. The exceptionally high operating capacity and regeneration efficiency of D301 make it ideal for applications where the maximum possible throughput and minimum chemical dose are required.
Typical physical & Chemical characteristics:
Polymer Matrix Structure: Styrene Crosslinked with DVB
Physical Form and Appearance: yellow spherical beads
Whole Bead Count: 95% min.
Functional Groups: R-N(CH3)2 Tertiary Amine
Ionic Form ,as shipped: Free Base
Total Exchange Capacity, CL- form, wet, volumetric
1.4 eq/l min.
Water Retention inside of structure, CL- form: 50-60%
Moisture content %: 5% max.
Particle Size Range: 0.4mm-1.2mm¡Ý95%
Swelling (FB-CL) : 20%
Shipping Weight (approx.): 650-710 g/l
Specific Gravity, moist CL- Form: 1.03-1.06
PH Range, Stability: 0 - 14.
25L /bag,1000L /big bag with pallet.
201x7 is a high capacity, shock resistant, gelular,Type I ,strongly basic anion exchange resin supplied in the chloride or hydroxide form as moist, uniform, spherical beads. 201x7 is intended for use in all type of deionization systems and chemical processing applications..
Typical physical & Chemical characteristics
Polymer Matrix Structure: Styrene Crosslinked with DVB
Physical Form and Appearance: Clear spherical beads
Whole Bead Count: 95% min.
Functional Groups: R-N(CH3)3+
Ionic Form ,as shipped: CL
Total Exchange Capacity, CL- form, wet, volumetric
1.30 meq/l min.
Moisture Retention, CL- form: 45-52%
Particle Size Range: 0.4-0.8mm
Swelling CL-¡ú OH-: 18-20%
Shipping Weight (approx.): 670-720 g/l
Specific Gravity, moist CL- Form: 1.09
PH Range, Stability: 0 - 14.
25L /bag,1000L /big bag with pallet.