Hallo Good day we can supply Iron Scrap HMS 1 & 2 Origin - Japan Quantity 20 to 100K per month Interested importers kindly contact Long chain brokers please dont contact unless have direct contact with END buyer or Buyer Mandate - Need ICPO from direct buyer to end seller we assure best price and mark up ( conditional )
Iron scrap hms 1&2 (80:20) Subject: scrap hms 1&2 (80:20) Whereas: xxxx co. Ltd. With full corporate authority and responsibility hereby makes and confirms that it is ready, willing, and able to purchase 2500 mt +/- 5% (two thousand five hundred metric tons) (plus or minus five percent) of product under the terms and conditions agreed and contained in this contract; Whereas: maroon impex, with full corporate authority and responsibility hereby certifies, represents, and warrants that it has the commodity and is willing to sell and can fulfill the commodity specifications, quality, quantity, and timely deliveries agreed in this contract; and the product will be cut to one and a half (1.5) meter length as requested; and Whereas: upon consideration of the mutual agreements, promises, benefits, terms, and valuable consideration between and in the benefit of maroon impex and maroon impex have determined to enter into this sales and purchase contract in accordance with the following terms and conditions set out herein; Standard lot size
Finemakret imp&exp co., ltd located in guangdong china, major in the trading service from china . We have serval resource recovery station in china, can offer the very low price cargo like : Steel scrape /iron scrapr/metal scrape Before loading the cargo we will offer the live for you to check the cargo . You can also visit our location in shenzhen. After confirm the quality then arrange loading .
PRODUCT SPECIFICATIONS: Heavy melting steel (HMS) or heavy melting scrap is broken up into two major categories: HMS 1 and HMS 2, where HMS 1 does not contain galvanized and blackened steel, whereas HMS 2 does. HMS is typically traded as a blend of 1 and 2, either a premium blend (80/20) or lower grade mixes (70/30) and (60/40). For example, HMS 1 and 2 (80/20) should consist of HMS 1 and 2 in the ratio of 80% (HMS 1) and 20% (HMS 2). Each grade guarantees a minimum piece thickness: at least 1/4 inch (6.3 mm) for HMS 1, and 1/8 in for HMS 2 HMS 1 and 2 specifications as defined by ISRI (North America's Institute of Scrap Recycling Industries): ISRI SPEC 200 (HMS 1) Wrought iron and/or steel scrap 1/4 inch and larger in thickness. All pieces must be smaller than 60.24 in. ISRI SPEC 201 (HMS 1) Same as ISRI 200 except pieces must be smaller than 36.18 in. ISRI SPEC 202 (HMS 1) Same as ISRI 200 except pieces must be smaller than 60.18 in. ISRI SPEC 203 (HMS 2) Wrought iron and/or steel scrap, black and galvanized, 1/8 inch and larger in thickness. ISRI SPEC 204 (HMS 2) Same as ISRI 203 except pieces must be smaller than 36.18 in. ISRI SPEC 205 (HMS 2) Same as ISRI 204 except it may contain automotive scrap, except for thin guage material. ISRI SPEC 206 (HMS 2) Same as ISRI 205 except pieces must be smaller than 60.18 in.
Steel And Cast Iron Scrap Cast iron alloy scrap price 270 Euro exw
Heavy Melting Steel (HMS): Heavy melting steel is a designation for recyclable steel. It is categorised into two major categories: HMS 1 and HMS 2. The difference between the two is HMS 1 does not contain galvanized and cast iron, whereas HMS 2 does. Because both grades guarantee a minimum piece thickness â?? at least 1/4inch (6.3mm) for HMS 1, and 1/8 in for HMS 2 â?? consignments have a high density. The typical constituents are plates, truck parts, structural items, large machinery parts, automatic parts, pipes, post consumer steel goods. Quality Heavy metal ,Iron Scrap/ Metal scrap HMS 1 and HMS 2 scrap steel for sale
SPECIFICATIONS Steel Scrap in bulk according to grade HMS 1&2 Max size 1500*500*500 mm. 40% of HMS 2, sheets of max 4mm thick, max 5% of galvanized steel (close to ISRI 203), max 2% of soil is acceptable. Cast iron, baled scrap, non-ferrous metals, explosive shells of military type, any gas tubes (empty or full), radioactive materials, slag, melt, stones is not allowed. Oversize is not allowed.
We can supply. Quality HMS 1&2 (80:20 mix) Quantity/Volume 1kt to 20kt We can transport to any destination. Our main customers are Turkey and Egypt.
R50- R65 - IRSI CODES; The chemical composition is the standard for R-50 R-65 Tee rails original weigh 50 pounds per yard or heavier,6 meters long and over. Material to be suitable for rerolling into bars and shapes. Free from bent and twisted rails, frog, switch and guard rails, rails with split heads and broken flanges. Continuous welded rail may be included provided no weld is over 9 inches from end of the piece of rail. Free from Fluff, Nonferrous inclusions, excessive rust and other impurities. Free from war and explosives, shells, cartridges, other arms and ammunitions used or otherwise and any closed containers. Free from any radioactive materials, any harmful chemicals, substances, and coatings any organic waste any other harmful substances. Dirt, dust, rust fluff and other impurities not allowed over 05 %. The rails are to be neatly bundled and secured with iron wire or straps, provided with adequate lifting hooks. Individual bundles not to exceed 5 MTW. Used Rails R50 - R65 Chemical Composition Used Rails; C: 0, 54 - 0,82 Si: 0,18-0,40 Mn: 0, 60-1, 05 S: 0.04 max P: 0,035 max As.: 0, 01 max of Mass share Norms: R-50 GOST7173-75 and R-65 GOST-8165-75 The scrap consists of R-50 (51, 67 kg/m) R-65 (64,72 kg/m) Used Rail ISRI 27-29 ISRI-CODES; (27) Rail, Steel No. 1. Standard section tee rails, original weight 50 pounds per yard or heavier, 10 feet long and over. Suitable for re-rolling into bars and shapes. Free from bent and twisted rails, frog, switch, and guard rails, or rails with split heads and broken flanges. Continuous welded rail may be included provided no weld is over 9 inches from the end of the piece of rail. (28A) Rail, Steel No. 2 Cropped Rail Ends. Standard section, original weight of 50 pounds per yard and over, 18 inches long and under. (28B) Rail, Steel No. 2 Cropped Rail Ends. Standard section, original weight of 50 pounds per yard and over, 2 feet long and under. (28C) Rail, Steel No. 2 Cropped Rail En ds. Standard sec t ion, original weight 50 pounds per yard and over, 3 feet long and under. (29) Rail, St eel No. 3.Standard section tee, girder, and/or guard rails, to be free from frog and switch rails not cut apart, and contain no manganese, cast, welds, or attachments of any kind except angle bars. Free from concrete, dirty and foreign material of any kind. The rails can be cut to the length the buyer wants
We are an authorized representative of an european supplier who is engaged in trading high ferrous scrap, alternative material for cast iron industries. The most tradable by-products are cast iron and steel slags (fe 85%-95%). The supplier always take several probes for more accuracy to get average numbers and make chemical analysis before propose it to buyers. In other words, they only supply material which will be comfortable for client, to avoid such problems as purchase returns and further misunderstanding. Other tradable material : Steel scrap after eaf/bof slag The material available on regular monthly basis with qty 2000+ m.T Most interesting types of slag for us are blast furnace/basic oxygen process/ladle furnace slags, mill scale. The material is a great substitute for pig iron. The key buyers will be cast iron foundries, This is good material for cast iron foundries, especially gray iron foundries. Offer : fob kotka $150 per mt Cast iron scrap : form slag , 2000 mt is now in port kotka, in finland and available on regular monthly basis. Can also provide sample and can arrange meeting with supplier also on port.
