Factory saqure self-luminous road stud delineator with reflective panels Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF08 Product name Factory saqure self-luminous road stud delineator with reflective panels Material ABS+self luminous Color white/ yellow/ red/ green/ black Size 100mmÃ?100mmÃ?20mm Weight 133g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF08 (1)YF08 (1)YF08 (1)_.jpgYF08 (2)_.jpgYF08 (3)_.jpgYF08 (5)_.jpgYF08 (6)_.jpgYF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT Nano-fluorescent self-luminous cat eye road stud delineator with glass beads Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF10 Product name YT Nano-fluorescent self-luminous cat eye road stud delineator with glass beads Material ABS+glass beads+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 110mmÃ?110mmÃ?66mm Weight 138g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF10 (2)YF10 (3)YF10 (5)YF10 (4)YF10 (1)YF10 (1)YF10 (3)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT transparent self-luminous ABS road stud delineator as a traffic signal Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF14 Product name YT transparent self-luminous ABS road stud delineator as a traffic signal Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 180mmÃ?48mmÃ?40mm Weight 120g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF14 (6)_YF14 (1)_YF14 (6)YF14 (1)YF14 (1)_YF14 (1)YF14 (2)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT transparent self-luminous ABS road stud delineator as a traffic signal Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF14 Product name YT transparent self-luminous ABS road stud delineator as a traffic signal Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 180mmÃ?48mmÃ?40mm Weight 120g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF14 (6)_YF14 (1)_YF14 (6)YF14 (1)YF14 (1)_YF14 (1)YF14 (2)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
YT transparent self-luminous ABS road stud delineator as a traffic signal Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF14 Product name YT transparent self-luminous ABS road stud delineator as a traffic signal Material ABS+PMMA+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 180mmÃ?48mmÃ?40mm Weight 120g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF14 (6)_YF14 (1)_YF14 (6)YF14 (1)YF14 (1)_YF14 (1)YF14 (2)YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
Road stud Road stud kt-201: size: 10.2cm(l)*10.2cm(w)*1.8cm(h) filling material: epoxy colophony crust material: abs pressure durability: 25t color of reflector: amber/white/red color of the crust: yellow/white material of the reflector: pmma/pc (either is ok) photometric values: white reflector 500 (mcd/lux) yellow reflector 300 (mcd/lux) Pakage
1.Material:aluminum alloy 2.Size:100*100*65mm 3.Weight 290g Carton packing
1.Material:abs and sand 2.Size:100*100*20mm 3.Weight:270g Carton packing
YT Factory Energy Storage Self-luminous Highway Road Reflective Delineator as Traffic Signs Self-luminous series These self-luminous road studs and delineators are highly durable devices, providing day and night visibility in adverse weather conditions. These are reflector type road stud offering a long response time and reflect light from vehicles headlight back to the driver's eye. They are used to provide distinct outline of pavement markings during poor visible conditions under fog and bad weather conditions. The fluorescent part is made of nano - fluorescent material. The greatest convenience is that they dont need any electric power or solar panel. Only with light, not even the sunshine, it can also absorb the daylight and storage it in the polymer material made part. Till the night, it shines out and guide the drivers for road safety. For further usage of warning purpose, LED solar road stud can also be combined with self-luminous function so that it provides drivers double safety guarantee. Product Code YF18 Product name YT Factory Energy Storage Self-luminous Highway Road Reflective Delineator as Traffic Signs Material Aluminium+Nano-fluorescent material Color white/ yellow/ red/ green/ black Size 150mmÃ?150mm Weight 48g Application reflective panel, road stud, delineator, speed humb, etc, Feature light weight, lower cost-effecitve, high reflectivity, long-lasting, easy installation, wide range of application Payment terms T/T, L/C, Western union, Trade Assurance YF18 (4)_YF18YF18__ YF18 (3)YF18 (2) YF self-luminating series table of brightnessYetong road studplastic road stud_application Procedures and precautions for installation of road stud. 1.Environment: keep the ground clean, out of water and dust. The ground must be dry. 2.Drill hole on the ground: drill holes according to the distance of the two holes on the road stud. Then put the road stud on and make holes to holes match and clear the dust. If the spike is with anchor, then drill a hole 5mm deeper than the anchor to put it into the hole. And also need to put some glue into the hole. 3.Ratio of resin glue: make it 1:1 with the A and B type of resin glue. It will dry faster in summer than winter. 4.Apply glue: use a tool to take 5g glue and put it on the bottom of the road stud. Then put the road stud immediately on the ground. Finally install the screws. 5.Inspection: inspect whether the bottom is empty or not in case the glue comes out. 6.Time of solidification: it takes one day in winter and half day in summer.
