This is Bangkit from Chip 1 Exchange, we are an electronic component distributor.
The vp series power amplifier offers clean, reliable power in a durable enclosure. If you need professional amplification performance, the vp series is perfect for delivering pure, consistent wattage night after night. With six models power upto 1200 watts, the vp series is ideal for powering pa systems and dj rigs. To ensure seamless, reliable performance, the amp features variable-speed cooling fans for thermal stability, along with short-circuit, thermal, over current, thermal protection. For connecting convenience, the vp series boasts xlr and speakon &banana binding post outputs. The unit also provides front panel indicators for signal, limit, protect and power, plus level controls for channels 1 and 2. Selectable modes for stereo and mono bridge give you even more flexibility. Selectable output power range to drive professional loudspeakers without clipping Variable-speed cooling fan for thermal stability and reliability Xlr balanced inputs and speakon &banana binding post outputs Limiter indicator for amp output protection Stereo and mono bridge Variable speed fan for low noise Comprehensive front panel indicators including signal, limiter, protect and power Dc output protection and short circuit protection Frequency response 10hz c 50khz at 1.5 db Total harmonic distortion: less than 0.05% Input sensitivity & impedance: 0.775v Signal to noise (20 hz - 20 khz) > 95db Shipping dimensions (wxdxh) 585x 580 x 165mm
8ohms Stereo Power(RMS): 2X1050W 4ohms Stereo Power(RMS): 2X1600W Frequency Response(+o/-0.3dB, 1W/8ohms): 20Hz-20kHz, -3dB@135kHz Power Bandwidth (rated power at 4ohms 1%THD+N): 20Hz-20kHz, -. 1.1dB/+0dB TourClass Protection: ACL, IGM, AutoRamp, short circuit, DC voltage, turn-on/off transient, current inrush, sub/ultrasonic input THD+N (1kHz 1W ): -60dB Voltage Gain (rated power @ 8ohms): X40dB Input Sensitivity (rated power at 8ohms): 0.8V Input Impedance (balanced/unbalanced): 20Kohms/10Kohms S/N Ratio ("A"weighted, full power at 4ohms): 96.5dB Crosstalk ("A"weighted, full power@4ohms): >-65dB Class: 3 Step H Input Connectors (per channel): Female XLR (pin 2+, configurable for pin 3+). TRS (tip+) Output Connectors (per channel): 5-way binding posts or Speakon connectors (market dependent) Supply Power: 4158W Power Supply (factory configured): AC220V/230V, 50-60Hz Cooling: Two side panel variable speed DC fans, better than conventional cooling Controls: Front panel: 2 attenuators, power switch; Rear panel: Signal ground lift & mode switches. LED Indicators (per channel): Signal, Protect, Active, Critical Construction: Steel chassis, 16 gauge. Casting Aluminum front panel. Dimensions (HXWXD): 132X483X480mm (3U) Net Weight: 33.5kg Gross Weight: 34.35kg.
F600 Power Amplifier Key Feature: * 2/3U high, heavy duty steel chassis * Modular construction for easy servicing * Symmetrical layout for even weight distribution * High efficiency toroidal power transformer * Oversized, high energy, linear power supply * 3 steps, Class H Audio topology * Stereo, parallel or bridged operation * Twin balanced inputs (Neutrik XLR connectors) * Dual Speakon and Binding posts outputs * High quality components used throughout * Dual, continuously variable speed fans * Efficient two sides cooling, the efficiency is better than back to front cooling * Active, signal, protect and critical indicators * Duraluminium, 8mm thick front-panel * Unobtrusive carrying handles * Voltage Gain: 35 or 40 dB . Specification: 8ohms Stereo Power(RMS): 2X300W 4ohms Stereo Power(RMS): 2X462W 8ohms Bridged Power(RMS): 968W Frequency Response(+o/-0.3dB, 1W/8ohms: 20Hz-20kHz, -3dB@135kHz Power Bandwidth(rated power at 4ohms 1%THD+N): 20Hz-20kHz, -. 1.1dB/+0dB TourClass Protection: ACL, IGM, AutoRamp, short circuit, DC voltage, turn-on/off transient, current inrush, sub/ultrasonic input THD+N (1kHz 1W ): -60dB Voltage Gain (rated power @ 8Ic): X35dB Input Sensitivity (rated power at 8Ic): 0.97V Input Impedance (balanced/unbalanced): 20KIc/10KIc S/N Ratio ("A"weighted, full power at 4ohms): 99dB Crosstalk ("A"weighted, full power@4ohms): >-63dB Class: 3 Step H Input Connectors (per channel): Female XLR (pin 2+, configurable for pin 3+). TRS (tip+) Output Connectors (per channel): 5-way binding posts or Speakon connectors (market dependent) Supply Power: 1320W Power Supply (factory configured): AC220V/230V, 50-60Hz Cooling: Two side panel variable speed DC fans, better than conventional cooling Controls: Front panel: 2 attenuators, power switch; Rear panel: Signal ground lift & mode switches. LED Indicators (per channel): Signal, Protect, Active, Critical Construction: Steel chassis, 16 gauge. Casting Aluminum front panel. Dimensions (HXWXD): 88X483X480mm (2U) Net Weight: 19.2kg Gross Weight: 23kg.
Supplier: Labels, carton boxes, books, metalized printing, printed materials, electronic components, parts, panels, note book printing, text book printing, cake box,groundnut oil
Buyer: ,
Supplier: Car audio capacitor and amplifier
1.Extreme Low E.S.R.:less than 0.0015ohm; 2.Auto on/off four-digit display; 3.LED indicator lights; 4.Electronic Polarity Protection Circuit; 5.Over-voltage Protection Circuit; 6.Normal working temperature:minus 40íµ to 105íµ; 7.Mounting brackets & hardware included; 8.Optional digit color: red, blue & white 9.Available in:0.3F, 0.5F, 1.0F, 1.5F, 2.0F, 3.0F, 5.0F
Buy 3 get 1 free plus free shipping ... Delivery Time : 2 days maximum Payment: Bank Transfer
Supplier: Integrated circuit, diodes, amplifer, capacitor, resistor and other electronic components
