Lovson Entetrprise

The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.

Neodymium magnets (also known as NdFeB, Neo or NIB magnets), are strong permanent magnets made from an alloy of neodymium, iron & boron. Part of the Rare-Earth magnet family, they have the highest magnetic properties of all permanent magnets. Due to their high magnetic strength and relatively low-cost, they are the preferred choice for many consumers, commercial, industrial and technical applications.NdFeB is divided into sintered NdFeB and bonded NdFeB. Bonded NdFeB is magnetic in all directions and corrosion resistance and is divided into Bonded Compression NdFeB Magnet and Bonded Injection NdFeB Magnet; while sintered NdFeB is easy to corrosion, the surface requires coating, generally divided into axial and radial magnetic charging. Advantages of Sintered NdFeB Magnet : 1. Very hard and brittle, high diamagnetic resistance, high cost / performance ratio, not suitable for high working temper ature; 2. Magnetic performance is higher than that of the rare earth cobalt permanent magnet, the residual magnetic induction strength, magnetic induction coercivity, the maximum magnetic energy product is very high, is the current magnetic performance of the best permanent magnet; 3. High cost performance.

Fasteners are the general term of the class of mechanical parts used in fastening two or more parts (or components) into a whole. It is widely used in energy, electronics, electrical appliances, machinery, chemical, metallurgy, mold, hydraulic and other industries, at the same time, in various kinds of machinery, equipment, vehicles, ships, railway, bridge, construction, structure, tools, instruments, chemical, instruments and supplies, you can see all kinds of fasteners, is the most widely used mechanical foundation parts. It is characterized by a wide variety of variety specifications, different performance uses, and a very high degree of standardization, series, and generalization. Therefore, a class of fasteners that already have national standards is called standard fasteners, or simply standard ones.

AINiCo is composed primarily of Aluminum Nickel Cobalt and also Copper and Titanium. They are manufactured through either casting or sintering process. Cast AINiCo may be manufactured in complex shapes such as horseshoes not possible with other magnet materials. Sintered AINiCo offer slightly lower magnetic properties but better mechanical characteristics. it can be efficiently magnetized in any direction, and for anisotropic AINiComagnet, it generally has greater magnetic capacitive in a preferred orientation than isotropic types. AINiCo is hard and brittle, Machining or drilling cannot therefore be accomplished by ordinary methods. Holes are usually cored in at the foundry, and magnets are cast close to final size and then finish machined to closer tolerances. â?¢ Advantages of AlNiCo Magnet: 1.Customized designs are available. 2.Max working temperature can be as high as 550�°C. 3.Disadvantage: Br and BH(max)are not as high as rare earth magnet. 4.High energies and relatively low coercivity. 5.High magnetic flux density; low mold charge stable temperature properties; easy to shap.

Samarium Cobalt (SmCo) magnets are made by a sintering process and exist in two forms. The first is Sm1Co5(SmCo 1:5),which has a maximum energy product of between 14 and 24MGOe. The second and more common form is Sm2Co17(SmCo 2:17) which has a maximum energy product of between 22 and 32 MGOe. The main Sm2Co17 alloy is around 35% Samarium (Sm)and 60% Cobalt (Co)with the balance being from varying amounts of lron (Fe) Copper (Cu). Hafnium (Hf) and Zirconium (Zr). Praseodymium (Pr) may also be used. Sm1Co5 is made of only Sm and Co and has excellent corrosion resistance. â?¢ Advantages of SmCo Magnet: 1.Superior resistance to high temperature. 2. Excellent resistance to corrosion, no coating is needed for surface protecting. 3.High working temperature. 4.SmCo is suitable for machines with high magnetic requirements and good for strict working environment requirement.

Ferrite Magnet is manufactured from oxide material by powder metallurgical process. Its advantages include: low-cost excellent corrosion resistance, resistance to be demagnetized etc. The normal working temperature of Ferrite Magnet is between-40C and +250C.It can be magnetized before or after assembling. Generally, Ferrite Magnet can be machined to regular shapes like segments, blocks, rings and discs etc. The normal grades for sintered Ferrite Magnets are Y10,TY25, Y30, Y30BH, Y35, etc. Advantages of Ferrite Magnet: Ferrites have isotropic characteristics, weak magnetic performance, has the same magnetic performance in any direction, multipolar magnetic charge. The main raw material of ferrite is oxides, so it is not corroded by high temperature, high humidity or chemicals (except strong acid and base); with excellent diamagnetic impedance, no flux loss before and after assembly and magnetic charging; working temperature is-40C to + 250C, poor temperature coefficient; Br temperature coefficient is-0.2% /C, 0.2% under Br, etc. per 1 Cincrease; high hardness, wire cutting and grinding; ferrite is brittle and fragile during production and transportation. magnetic requirements and good for strict working environment requirement.

Pularin: Foot ball shaped 60 atoms of carbon at edges is layed in pularin.Pularin atoms are arranged in ball. Each atom is called Bucky balls and tubes are called Bucky tubes or Nano tubes.Each nano tube is 1 to 7 nm diameter i.e 1nm=50000 part of a hair sting. where? 1)mangampet ,cuddapah dist.Ap,India.app 800 ppm(parts prer million)info given by stanford University. Cost: 150 times costlier than gold. 10 grams pularin $23000 to $45000 also info given by Bucky-USA website. Special uses if this becomes common: 1)Pularin coting on aeroplanes withstands from thunders ,rains ,Flashes etc. 2)Bullet proof ackets 3)curing cancer etc.

Focus-6100 butyl tapes are mainly made of butyl rubber with excellent performance in waterproofing and sealing. Main Specification (Customized size is acceptable.) 3.0mm thickness * 12mm width *15m roll length 2.5mm thickness * 8mm width * 15m roll length 2 mm thickness * 15mm width * 20m roll length 2.5 mm thickness * 8mm width * 20m roll length Main Color black, grey, white Technical Data Product Series FOCUS-6100 Application Composite Materials Industry Elongation 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 23N/cm Tensile Strength 220KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet. Advantages Strong adhesion. Wide application temperature range. Excellent performance in waterproofing and sealing. Applications * During the production of vacuum extraction process for wind mill blade, it has excellent sealing property between vacuum bags and molds. During the production of vacuum extraction processfor fiberglass, it has excellent sealing property between vacuum bags and molds. * During the production of vacuum extraction process for cabin cover, it has excellent sealing property between vacuum bags and molds. * As auxiliary materials, our Focus-6100 series are widely used in the production of wind mill blade, fiberglass, cabin cover, car tail bracket, automotive engine cover, yacht. * Our products have excellent sealing property between vacuum bags and mold during the vacuum extraction process.