This load moment indicator is a tower crane safety system. It has the following functions: Working temperature: -20 --- + 60 -40 --- + 80 Working humidity: í_ 95%/25 Combined error: 1% Power supply: AC220V (to be customized according to clients requirement) Parameter: Rated load, actual load, trolley amplitude, hook height and moment percentage Signal lamp&buzzer: Flickering yellow lamp and buzzers discontinuous response indicates early warning, whereas red lamp and buzzers continuous response indicates alarm and relay outputs. Other functions: Records downloading; sensors self-diagnostic; applicable to tower crane with variety of falls.
This load moment indicator is a tower crane safety system. It has the following functions: Working temperature: -20 --- + 60 -40 --- + 80 Working humidity: í_ 95%/25 Combined error: 1% Power supply: AC220V (to be customized according to clients requirement) Parameter: Rated load, actual load, angle of the jib, hook height and moment percentage Signal lamp&buzzer: Flickering yellow lamp and buzzers discontinuous response indicates early warning, whereas red lamp and buzzers continuous response indicates alarm and relay outputs. Other functions: Records downloading; sensors self-diagnostic; applicable to tower crane with variety of falls. carton
his anti-collision device is a tower crane safety system. It has the following functions: CXT/800 system protection Tower crane Anti-collision protection If tower cranes are with the same height, this system can control and handle it effectively, once detecting that the running jibs interfere with each other automatically. While not with the same height, this system can also work effectively once anticipating the hook or cable of the higher tower crane may collide the jib or counter jib of lower one. Zone(obstacle) anti-collision Due to the complexity of some sites, the system can automatically and effectively determine up to 10 prohibited zones in which the hook or jib are not allowed to operate. Boundary protection Complicated environment usually exists around work site. The CXT/800 system can be preset with a up to 30-point boundary protection area in which the operating or over-flying of hook is not allowed. It can effectively prevent accidents from happening. Pre-alarm/alarm and control CXT/800 system allows the operator to work at maximum efficient way and optimize the use of Crane. Once monitoring the pre-set data for possible collisions in crane interference area and over-flying of sensitive areas, there will be pre-alarm and visual and audible alarm and the system will stop the maneuver automatically to maintain a safety margin.
Cxt/20p-i tower crane load moment indicator Working temperature: -20 --- + 60 -40 --- + 80 Working humidity: 95%/25 Combined error: 1% Power supply: ac220v (to be customized according to clients requirement) Parameter: Rated load, actual load, trolley amplitude, hook height and moment percentage Signal lamp&buzzer: Flickering yellow lamp and buzzers discontinuous response indicates early warning, whereas red lamp and buzzers continuous indicates alarm and relay outputs. Other functions: Records downloading; sensors self-diagnostic; applicable to tower crane with standard fall Remarks: cxt/20p-i is a basic model while cxt/20p-ir add the function of slewing indication and cxt/20p-if adds the function of anemometer.
Cxt/800anti-collision and zone protection system Cxt/800 system protection Tower crane anti-collision protection If tower cranes are with the same height, this system can control and handle it effectively, once detecting that the running jibs interfere with each other automatically. While not with the same height, this system can also work effectively once acticipating the hook or cable of the higher tower crane may collide the jib or couter jib of lower one. Zone(obstacle) anti-collision Due to the complexity of some sites, the system can automatically and effectively determine up to 10 prohibited zones in which the hook or jib are not allowed to operate. Boundary protection Complicated environment usually exists around work site.The cxt/800 system can be preset with a up to 30-point boundary protection area in which the operating or over-flying of hook is not allowed. It can effectively prevent accielents from happening. Pre-alarm/alarm and control Cxt/800 system allows the operator to work at maximum efficient way and optimize the use of Crane. Once monitoring the pre-set data for possible collisions in crane interference area and over-flying of sensitise areas, there will be pre-alarm and visual and audible alarm and the system will stop the maneuver automatically to maintain a safety margin.
INSTALLATIONS Weight Measurement Range: 0T~400T. Resolving Ability: 0.1T. Synthetic Errors: â?¤5%F.S. Equipped with Output Interface RS485. Working Condition: ï¼?20ï½?60. Relative Moisture under Working Condition: 90%RHï¼?20ï¼?. Working Voltage: AC220V±25%. Preset Output Contact Capacity: AC220V 7A. IP Grade: weight sensor with IP68; Monitor with IP64.
WTL-A220 Load Moment Indicator is a new type of smart weigh overload protector, which measures the changes of the weight of the loaded goods by a preset weight sensor and displays the actual load instantly on the display instrument. When the load reaches the given point of rated load, the acousto-optic alarm of the hoisting weight limiter will be triggered, with the switching value output displayed. The whole system is composed of sensor, connecting cable, microcomputer host and so on. The device is designed and manufactured in accordance with requirements of GB 12602-2009 Lifting Machinery Overload Protection Devices and GB / T 3811-2008 Crane Design Specification. With reasonable layout, easy installation, simple operation, WTLA220 Load Moment Indicator works well with high accuracy and other advantages Weight Measurement Range: 0T~400T. Resolving Ability: 0.1T. Synthetic Errors: â?¤5%F.S. Equipped with Output Interface RS485. Working Condition: ï¼?20ï½?60. Relative Moisture under Working Condition: 90%RHï¼?20ï¼?. Working Voltage: AC220V±25%. Preset Output Contact Capacity: AC220V 7A. IP Grade: weight sensor with IP68; Monitor with IP64.
RC-A11-II integrated load moment indicator with anti-collision&zone protection system and remote online monitoring system.It indicates real time working states of tower crane and tower crane group both on tower crane and on the online computer.The system adopted full-touch mode of operation,and the most advanced ARM system,higher integration,greater precision data acquisition.The system can show the operator and manager the most comprehensive working states of tower crane in operation. At the same height:the system will auto detect and deal it with if any interference within running radius of slewing mechanism. At the different height:the system will auto detect and deal it with if any interference between higher hook and lower slewing mechanism. The system can set up to 10 different protection zones,prohibit flying over sensitive areas such as power lines,schools,highways,building etc.Try to achieve max.working area of tower crane within ensuring tower crane safety.
Engine Crane
