Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Supplier: Specialty metal products: titanium, stainless steel, and copper manufactured products, bars, pipe, tubular, sheet, plate, coils, etc. scrap metal: used rails, and copper mill berry & cathode. crude oil, gas & fuel products: en590, jet fuel, ago, bonny light crude oil, gasoline, espo, d6, d2, petcoke, etc. food products: sugar, soybeans, wheat, etc. fertilizers: urea and dap ore & minerals: lithium
Supplier: Anode grade green petroleum coke, calcined petcoke coke gor aluminium smelter, solid coal tar pitch, smelter grade alumina, aluminium fluoride, synthetic cryolite , silicon metal
magnesium ingots
carbon cathode blocks
cold ramming paste, iron ore hematite, iron ore magnetite, steel billets, graphite electodes, electodes paste
semi coke, ferro chrome, ferro silicon, ferro manganese
calcium carbide, fluorspa, limestone
quick lime
hydrated lime
gypsum
silica sand
talc
steel blooms (collector bar)
cement clinker
palm oil
sunflower oil
corn oil
soybean oil
soya fatty acids oil
sesame oil
electrical calcined anthracite (eca)
steam coal
fuel grade petcoke
Buyer: Anode grade green petroleum coke
calcined petcoke coke gor aluminium smelter
solid coal tar pitch
smelter grade alumina
aluminium fluoride
synthetic cryolite
silicon metal
magnesium ingots
carbon cathode blocks
cold ramming paste
iron ore hematite
iron ore magnetite
steel billets
graphite electodes
electodes paste
semi coke
ferro chrome
ferro silicon
ferro manganese
calcium carbide
fluorspar
limestone
quick lime
hydrated lime
gypsum
silica sand
talc
steel blooms (collector bar)
cement clinker
palm oil
sunflower oil
corn oil
soybean oil
soya fatty acids oil
sesame oil
electrical calcined anthracite (eca)
steam coal
fuel grade petcoke
Bitumen , All Grades
Supplier: 1 steel, cooper, aluminum and other metal materials and products.
2 chemical ( hydrochloric acid, sulfuric acid nitric acid, hydrogen peroxide, formic acid, ammonia water, gacial acetic acid, ethanol, sodium hypochlorite, caustic soda, formaldehyde , methanol and many other )
3 agricultural commodities (wheat, , rice, barley, soybeans, corn, lentils, beans, chickpeas, green peas, maize)
4 spices and meats
5 cooking oils (refined and crudes)
6 flour (wheat flour, rice flour, yeast,)
and many other commodities.
Services: Consultancy, international marketing agency
KORYO SL 10W-40 Synthetic Technology Multi Grade Gasoline Engine Oil DESCRIPTION KORYO SL 10W40 is multi grade gasoline engine oil made by specially selected base oils using synthetic technology, suitable for all gasoline engines and light truck commercial vehicles requiring performance specification of API SL, including multi valve fuel injected, turbocharged, with/without catalytic converter engines, it has a low viscosity when cold to ensure quick and easy engine startup in cold conditions, High thermal and oxidation stability, Good resistance against foaming, corrosion and wear and maximizes engine life and fuel saving PERFORMANCE : API SL PACKAGE : 1L, 4L, 6L, 20L, 200L Plastic Can/Steel Tin Can
BASE OIL SN 100-150-300-500-600-700 Base oil is a type of oil which is used as a base for lubricants. The main element of lubricants (volume wise) is base oil and it forms about 95% of lubricants weight. In some lubricants (Compressor and hydraulic oil) 99% of the oil is consisted of base oil and only the 1% which is left contains additives. Base oils can be reached from oil based and non-oil based resources. Most of the base oils used in the world are obtained from crude oil refining. Most of the compounds which form base oils are Paraphinic, Naphthenic and aromatic compounds. Base oils chemical properties and their impact on the usage of final lubricant: 1 volatility: reduction of the oil, oil thickening, sediments 2 surface activity: foaming, pressure tolerance, air release, emulsion expansion 3 oxidations: sediments, oil thickening, metal oxidation, mud forming 4 Viscosity: Fluidity in lower degrees, energy waste, abrasion protection, proper cooling 5 being soluble: Motor neatness, sealant compatibility, process applications, formulation sustainability The base oil which is extracted from crude oil is called mineral base oil which is categorized in two types (Paraphinic and Naphtshic). Paraphinic oils are consisted of normal hydrocarbons and Iso hydrocarbons. Naphthic oils are consisted of annular full hydrocarbons. Paraphinic oils have certain attributes in comparison with naphthic oils such as;
Solest 68 is a formulated ISO VG68 synthetic polyol ester (POE) lubricant designed for commercial and industrial refrigeration and air conditioning compressors with over 25 years service in the field. Designed to maximize lubrication in HFC systems, Solest 68 provides superior bearing protection with greater film strength than standard HFC lubricants. This product provides effective wear protection for steel and aluminium surfaces for increased system life and improved efficiency. Solest lubricants are designed for standard factory fill of air conditioning and industrial refrigeration equipment, as well as for OEM retrofitting operations. CPI laboratory studies and OEM compressor bench tests have afforded a product line specifically designed to meet key system needs. Soles lubricants are not hazardous under 29 CFR 1910.1200. They provide improved properties over conventional mineral oils in all aspects, including viscosity index, flash and fire points and pour point. Applications and Compressor Type HFC, HCFC, HFO Refrigeration Reciprocating, Screw, Rotary, Centrifugal, Scroll Compressors Features and Benefits Thermally stable Longer system life Improved oil management Efficiency gains Corrosion protection Enhanced system reliability and reduced down-time Excellent bearing lubrication Longer compressor Life Optimized System performance Reduced operating costs Environmentally friendly Biodegradable Excellent lubricity Increased efficiency, reduced cost of operation Outstanding Miscibility The performance of an HFC system is optimized when the lubricant and refrigerant mix to form a single, clear phase. Miscibility lowers the viscosity of the lubricant carried through the system, so the lubricant can more efficiently return to the compressor. Mineral oils are not miscible with HFCs whereas Solest 68, as a polyol ester has a controlled level of miscibility with HFC gases. Excellent Thermal Stability Sealed tube results (ASHRAE 97) indicate that Solest 68 provides excellent stability in the presence of HFC refrigerants. In addition to outstanding stability, this lubricant shows no adverse effects to metals and other materials of construction.
Solest 220 is a formulated ISO VG220 synthetic polyol ester (POE) lubricant designed for commercial and industrial refrigeration and air conditioning compressors with over 25 years service in the field. Designed to maximize lubrication in HFC systems, Solest 220 provides superior bearing protection with greater film strength than standard HFC lubricants. This product provides effective wear protection for steel and aluminium surfaces for increased system life and improved efficiency. Solest lubricants are designed for standard factory fill of air conditioning and industrial refrigeration equipment, as well as for OEM retrofitting operations. CPI laboratory studies and OEM compressor bench tests have afforded a product line specifically designed to meet key system needs. Solest lubricants are not hazardous under 29 CFR 1910.1200. They provide improved properties over conventional mineral oils in all aspects, including viscosity index, flash and fire points and pour point. Applications and Compressor Type HFC, HCFC, HFO Refrigeration Reciprocating, Screw, Centrifugal Compressors Features and Benefits Thermally stable Longer system life Improved oil management Efficiency gains Corrosion protection Enhanced system reliability and reduced down-time Excellent bearing lubrication Longer compressor Life Optimized System performance Reduced operating costs Environmentally friendly Biodegradable Excellent lubricity Increased efficiency, reduced cost of operation Outstanding Miscibility The performance of an HFC system is optimized when the lubricant and refrigerant mix to form a single, clear phase. Miscibility lowers the viscosity of the lubricant carried through the system, so the lubricant can more efficiently return to the compressor. Mineral oils are not miscible with HFCs whereas Solest 220, as a polyol ester has a controlled level of miscibility with HFC gases. Excellent Thermal Stability Sealed tube results (ASHRAE 97) indicate that Solest 220 provides excellent stability in the presence of HFC refrigerants. In addition to outstanding stability, this lubricant shows no adverse effects to metals and other materials of construction.
