- Material: 100Cr6, SKF3, GCr15, SKF3S; - Technical: Seamless , Process: Piercing, Cold Drawing, Spheroidizing Annealing, Annealing etc.; - Size Range: OD 10 ~ 160 mm, Wall thickness: 1~ 25 mm; Length: Customized; - Delivery Condition: (1) +C No heat treatment after the final cold drawing process, (2) +LC After the final heat treatment there is a suitable drawing pass,(3) +SR After the final cold drawing process there is a stress relieve heat treatment in a controlled atmosphere, (4) +A After the final cold drawing process the tubes are annealed in a controlled atmosphere, (5) +N After the final cold drawing operation the tubes are normalized in a controlled atmosphere; - Application: Widely Used in Bearing Industry and Automotive Parts, such as Hydraulic Cylinder Pipe, Steel ball, roller and collar of large machinery bearing, axis of rotation, blade, stator pump, profiling, sleeve, mandril, etc.; - Features: High and uniform hardness and wear resistance, and high elastic limit.
Airatrex Has Rapidly Established Itself As A Strong, Reliable And Trustworthy Supplier For Wide Range Of Bearings. Ideally Suited To The Engineering, Maintenance And Manufacturing Markets Ball Screw Support Barrel Roller Bearings Cam And Roller Follower Crossed Roller Bearings Cylindrical Roller Bearing Deep Groove | Radial Ball Bearings Double Row Angular Contact Double Row Self Aligning Linear Bearings Plummer Blocks
Introduction: Model no.:166 214 345 790 81107 81113 81114 81210 81216 81218 81222 Description: 1. The main components of cylindrical roller thrust bearing; the cylindrical roller and cage thrust assembies, the shaft washers, and the housing washers. 2. The cylindrical roller thrust bearings are simple in form and design. The bearings are produced in single row and double row designs. 3. The cylindrical roller thrust bearings are suitable for arrangements that have to support heavy axial loads. Features: Low axial section height, High load capacity, High rigidity and can support axial forces in one direction Restricted tolerances
This type bearing has a very high radial load capacity but no axial load capacity. With relative smaller radial measurements, it gives a higher limiting speed. Fc type has two outer rings with ribs, full set of outer ring(ourter ring, rollers and cages), and one inner ring. Cages are rib-type. Fcd type has two outer rings with ribs, full set of outer ring(ourter ring, rollers and cages), and two inner rings. Cages are rib-type. Fcdp type has two outer rings without ribs, full set of rollers and cages, two inner rings, two rib rings and one middle snap rib ring, Cages are pin-type. In the view of position of lubricating bore, they have following types Fc: the sides of outer ring have lubricating groove Fc/a1: the radial surface has lubricating groove and oil bore¡£ Fcd: the sides of outer ring have lubricating groove. Fcd/a1:the radial surface of outer ring has lubricating groove and oil bore. Fcd/a13:both the sides and radial surfaces have lubricating groove and oil bore. Fcdp:the radial surfaces of both outer ring and middle rib ring have lubricating groove and oil bore. 80x80x80cm
No.: nu6/241.3m Old no.£º32948h Dimension£¨mm£©£º241.3¡á374.65¡á127 Basic£¨kn£©£ºc, 1260£¬co, 2660 Mass£¨kg£©£º56.2.
Four-row cylindrical roller bearing fc202780, 100x135x80mm Why esg bearings? Quality advantages: 1. Good quality bearing steel; 2. Advanced heat treatment technique to enable high and even hardness and toughness; 3. High temperature back-fire stabilizes the bearing size; 4. P6 precision grade; ller bearings: Standard export packing
Part name: three-row cylindrical roller slewing bearing Part no.: 191.32.3855.000.41.1522 O.D. = 4136.4mm I.D. = 3658mm T = 200mm Module: 18 Nos of teeth: 227. Total weight: 2700kg.
No.: NNAL6/222.25-1Q4/C9W33XYA2 Old No.:154744QU Dimension(MM):222.25 D-298.45 B-225.425 Basic load(KN):C,1580 Co,4640 Mass(KG):45.2.
High-end Die cutting belts are manufactured and supplied by us.. These belts are constructed with the highest raw materials and feature strong cut resistance. Our belts are ideal for use with slider beds since they have little friction on the bottom surfaces. The multi-layered, flat cutting surface area of the die cutting belt eliminates the need for penetration when cutting challenging materials. The standard ATOM cutting systems' innovative belt shift device and automated adjustment of the mechanical positive stop can help the belt last a long time (1,000,000 Impressions-Standard). There are numerous types of die cutting belts available. The belt's application and selection will rely on the die-cutting material and toll that will be used. The diameter of the roller is a crucial consideration when choosing a belt. The thickness of the die-cutting belts causes the roller's diameter to rise. Specifications Tensile Strength is 700kgs/cm. Any width upto 2500mm.
