Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.
Basalt Fiber Series Fabric 1. Production: basalt fiber fabric is made of continuous basalt fiber textile yarn through warping, weaving and coating. 2. Weaving methods according to requirements: unidirectional cloth, plain cloth, twill cloth and grid cloth. 2. Application: reinforced mesh cloth, fireproof cloth, fishing rod cloth, luggage decoration cloth, electrical insulation cloth, bulletproof cloth, etc. 3. Packaging: 100M / roll (or customized as required). 4. Performance: high strength, high temperature resistance, good electrical insulation, non hygroscopic, acid and alkali corrosion resistance.High temperature resistance 1000 �° C 5. Specification and model: bfw16 * 20-100 (120) BFW: basalt fiber fabric;Completely replace carbon fiber sheet building reinforcement 16 * 20: the warp and weft density of yarn is 16 and 20 pieces / cm respectively; 100: the width of the fabric is 100 cm; (120): the mass per unit area of fabric is 120 g / m2. BFNP5*5-200(160) BFNP: basalt fiber mesh cloth (coated and shaped); 5 * 5: the longitude and latitude mesh size of the cloth surface is 5 and 5mm; 200: the width of the grid is 200 cm; (160): the weight of grid cloth per unit area is 160g / m2.
Basalt Fiber Series Fabric 1. Production: basalt fiber fabric is made of continuous basalt fiber textile yarn through warping, weaving and coating. 2. Weaving methods according to requirements: unidirectional cloth, plain cloth, twill cloth and grid cloth. 2. Application: reinforced mesh cloth, fireproof cloth, fishing rod cloth, luggage decoration cloth, electrical insulation cloth, bulletproof cloth, etc. 3. Packaging: 100M / roll (or customized as required). 4. Performance: high strength, high temperature resistance, good electrical insulation, non hygroscopic, acid and alkali corrosion resistance. 5. Specification and model: bfw16 * 20-100 (120) BFW: basalt fiber fabric; 16 * 20: the warp and weft density of yarn is 16 and 20 pieces / cm respectively; 100: the width of the fabric is 100 cm; (120): the mass per unit area of fabric is 120 g / m2. BFNP5*5-200(160) BFNP: basalt fiber mesh cloth (coated and shaped); 5 * 5: the longitude and latitude mesh size of the cloth surface is 5 and 5mm; 200: the width of the grid is 200 cm; (160): the weight of grid cloth per unit area is 160g / m2.
Product Structurals Brand Renaissance Pipe Fitting Inc Sizes Refer the specification Condition New Rating45 based on 122 reviews price Start from 30 USD Product Structurals Brand Renaissance Pipe Fitting Inc Sizes Refer the specification Condition New Rating 45 based on 122 reviews price Start from 30 USD TYPE 202 304 304L 304 304H 316 316L 316Ti 321 321H 317 317L 310 310S 409 410 420 430 etc OTHER HYDRAULIC TUBE CAPILLARY TUBE HORN TUBE BOILER TUBE IBR TUBE PRECISION TUBE Stainless Steel Structurals ASTM A 312 A 213 A 213 A 249 A 269 A 358 A 240 A 276 Carbon Steel Structurals ASTM A 106 A 53 API A 5L Gr A B C ASTM A 333 Gr 1 to 6 IBR NON IBR Alloy Steel Structurals ASTM A 335 GR P1 P2 P5 P9 P11 P22 P91 Copper Alloy Structurals Aluminium Copper Brass Gunmetal Nickel Alloys Structurals Monel 400 500 Inconel 600 625 Incolloy 800 825 Hastelloy 904 Titanium Tungston SIlver Nickel Zirconium Palladium Vanadium etc Angles We offer our clients a qualitative range of industrial steel angles that are manufactured in line with international quality standards These are available in various forms and are appreciated for quality attributes such as durability easy installation corrosion and abrasion resistance In addition we also customize these angles as per the specific requirements of the clients We have been offering a wide range of Angles in various forms such as Stainless steel flat bar Grade 200 300 series SS hot rolled flat bar and SS cold drawn flat bar to our clients These find applications in Architectural Applications Construction Industries Multistoried building Fastening industry Overhead cranes Fabrication and Bridges
ProductASME 165 orific flanges BrandRenaissance Pipe Fitting Inc SizesRefer the specification ConditionNew Rating43 based on 37 reviews priceStart from 20 USD RFP India is specialized in manufacturing high quality of Orifice Flanges The main function of an orifice flange is to propose right of entry to a pipe line for metering of gases or liquids An orifice plate is packed together between a pair of flanges when its being installed in a pipe line and the whole convention is referred to as an orifice flange amalgamation Jackscrews in the gathering make a simple abolition of the orifice plate Meanwhile the orifice plate which is the metering apparatus comprises a very thin plate with a square edge concentric and round opening in the focal point Two pressure tapholes are as well penetrated in each flange for to measure the dissimilarity of pressure throughout the orifice RANGE 15 NB to 60 1500NB in 150 LBS 300 LBS 600 LBS 900 LBS 1500 LBS 2500 LBS ASA 150 ASA 300 PN 6101625 4064100160 ETC available with NACE MR 0175 SIZE 15NB to 60 1500NB CLASS PRESSURE Class Pressure 150 300 600 900 1500 2500 PN6 PN10 PN16 PN25 PN40 PN64 DIMENSION B165 BS4504 EN1092 B1636 B1647 B1648 MSS SP44 STD STD ANSI Flanges ASME Flanges DIN Flanges EN Flanges BS Flanges API JIS NACE etc FEATURES Dimensional accuracy Corrosion resistance High efficiency Excellent finish Durable Stainless Steel Orifice Flanges Standard ASTM ASME ASA 182 Grade F 304 304L 304H 309S 309H 310S 310H 316 316TI 316H 316L 316LN 317 317L 321 321H 347 347H 904L Duplex Steel Orifice Flanges Standard ASTM ASME ASA 182 Grade F 44 F 45 F51 F 53 F 55 F 60 F 61 Aluminium Orifice Flanges Standard ASTM B247 B361 Grade 2024 6061 6063 6101 7075 Titanium Orifice Flanges Standard ASTM B381 Grade Grade 1 Grade 2 Grade 4 Grade 5 Grade 6 Grade 7 Grade 9 Grade 19 Grade 23 Carbon Steel Orifice Flanges Standard ASTM A 105A694 A350 LF3A350 LF2 Grade F42465256606570 Low Temperature Carbon Steel Orifice Flanges Standard ASTM A 350 LF2 A350 LF3 Alloy Steel Orifice Flanges Standard ASTM A182 Grade F1F5F9F11F22F91 Copper Alloy Orifice Flanges Standard ASTM ASME SB 61 62 151 152 Grade UNS NO C 70600 CU NI 9010 C 71500 CU NI 7030 C 71640 Nickel Alloy Orifice Flanges Standard ASTM ASME SB 564 160 472 Nickel 200 UNS N02200   Nickel 201 UNS N02201   Monel 400 UNS N04400 Monel K500 UNS N05500   Inconel K600 UNS N06600   Inconel 601 UNS N06601 Inconel 625 UNS N06625   Inconel 800 UNS N08800   Inconel 800H UNS N08810 Inconel 825 UNS N08825   Hastelloy C276 UNS N10276   Alloy 20 UNS N08020 Test Certificate Manufacturer Test Certificate as per EN 10204 31 nbsp Types Of Orifice Flanges SS 310 310S Orifice Flanges Duplex Steel UNS S31803 Orifice Flanges Stainless Steel 304 304L Orifice Flanges Duplex Steel Orifice Flanges Stainless Steel 316 316L Orifice Flanges Duplex Steel UNS S32205 Orifice F
Our export-quality padlocks are designed for superior security and durability, meeting global standards. Made from high-grade materials like hardened steel and brass, they offer exceptional resistance to corrosion, tampering, and harsh weather conditions. The locks feature precision mechanisms for smooth operation and enhanced protection against picking and cutting. Available in various sizes and designs, our padlocks can be fully customized to meet specific security needs. We offer personalization options such as engraved logos, unique keying systems, and custom finishes, making them ideal for bulk orders in industries, commercial spaces, or for personalized branding, ensuring reliability and customer satisfaction worldwide.
