Geo Textile Netting made of Natural Coco Fiber in White or Brown Coir. (Machine or Hand woven). Used to control Soil Erosion, at work sites, road construction areas, river banks etc.. as a protective measure/Mesh. Can be used as backing for hydro seed spraying. Specifications Mesh Hole size : 20mm x 20mm or 30mm x 30mm or (As per buyer’s requirement for any pattern and size) Supplied in rolls any length and any width (up to 2 meters of maximum width).
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
It uses polypropylene and rubber as the main raw material with various anti-oxidants, anti-aging and anti-UV additives. Advantage: 1. Excellent weather resistance, aging resistance, high tensile strength and elongation. 2. Wide temperature range from-40â?? to 100â??. 3. Good solderability and plasticity. 4. Eco friendly. Application: Basement, tunnel, grain depot, subway, reservoir, exposed roof, planted roof and driving roof. Specification: 1. Thickness: 1.2/1.5/1.8/2.0mm 2. Width: 2000mm 3. Length: 20m
TPO waterproof coiled material, namely thermoplastic polyolefin waterproof coiled material, is a new type of waterproof coiled material made of thermoplastic polyolefin (TPO) synthetic resin combining ethylene propylene rubber and polypropylene with advanced polymerization technology and adding antioxidant, antioxidant and softener. It can be made into reinforced waterproof coiled material with polyester fiber mesh cloth as internal reinforcement material, It is a waterproof product of synthetic polymer waterproof coiled material.
Thermoplastic polyolefin (TPO) rolls, which use advanced polymerization technology, combine the durability and weather resistance of ethylene - propylene (HP) rubber with the thermal weldability of polypropylene.The coil has long - term weather resistance and does not use plasticizer. Product Feature 1. Few auxiliary materials, convenient construction and good system integrity; 2. Excellent tensile, tear and puncture resistance; 3. No plasticizer, no plasticizer migration problem, excellent heat aging resistance and uv resistance, direct exposure, large thickness above the base, durable; 4. Hot air welding, high seam peeling strength (twice as high as PVC); 5. Fast welding speed; 6. Chlorine free and 100% recyclable, environmentally friendly; 7. Maintain excellent thermal welding performance for a long time, easy to repair; 8. Smooth surface, no fading, anti-pollution; Scope of application Widely used in industrial and civil and public buildings of all kinds of roofing waterproof works.
polyethylene(PVC) geomembrane, as a high performance waterproof and impermeable material, has many remarkable advantages. Thickness: 0.1mm-3mm Width: 2m-6m Color: Black/White/Other colors Following is our PVC geomembrane Thickness 1.6mm spceifications: Tensile Strength (vertical and horizontal): 20MPa/mm Elongation at Break (vertical and horizontal): 580% Right-angle tearing strength (vertical and horizontal): 180N/mm Water vapor permeability coefficient: Using temperature range: +70â??~ -70â?? Puncture strengthâ?¥360N Water impervious: 100% Root resistance: 100% Difference Between PVC Geomembrane and HDPE Geomembrane PVC geomembrane and HDPE geomembrane have significant differences in physical properties, treatment difficulty, joint treatment, puncture resistance, and resilience to deformation. Physical Properties and Suitable Environment: PVC membrane: relatively soft and easy to bend, suitable for general waterproofing projects, swimming pools, and wastewater treatment, etc. HDPE membrane: has higher strength and wear resistance, suitable for engineering projects with higher strength and durability requirements, such as water conservancy projects and landfills. Handling Difficulty: PVC membrane: Due to its flexibility, we can make seams in controlled factory conditions, typically requiring fewer on-site seams than HDPE geomembrane. HDPE membrane: Handling in cold weather conditions can be challenging and requires sewing outdoors. Puncture Resistance: PVC membrane: It is harder to penetrate than HDPE and has high elongation characteristics, allowing it to adapt to site changes without reinforcement. HDPE membrane: While it has elasticity, it becomes plastic after exceeding its yield point and no longer has elasticity. Deformation Recovery: PVC membrane: Most of the deformation can be recovered, with a high tensile elongation, suitable for engineering projects with larger design strain limits. HDPE membrane: Deformation after exceeding the yield point cannot be recovered, and the material properties will change. We should select the appropriate geomembrane according to the specific project requirements and the use environment. HDPE geomembrane is suitable for projects that require high strength and durability, while PVC geomembrane is suitable for general waterproofing projects and water treatment.
TJ-789 TPO Waterproof Membrane TPO Waterproof Membrane takes TPO elastomer as base material,adding fire retardant filling,anti weathering pigment filling,anti oxidization agent and light stabilizer,through high speed mix,melting extrusion,and calendering into waterproofing sheet material. Firstly developed in the early 20 centuries,it is extensively used for rooftop waterproofing projects under the installation of mechanical fasteners. With the combination of the great anti-weathering of EPDM and the weldability of PVC sheet,it defines the leading position in waterproofing industry TPO waterproof membrane has 0% plasticizer and no chloride,generating zero harmful gas when welding Application: Extensively used for the waterproof projects of industrial and residential buildings and public constructions Installation Guide 1. Substrate Requirements: Clean,no bugle and pointy object 2.Installation Steps(Mechanical Fastener) Substrate Clean Pave PE film Pave Insulation board Pre-applied TPO Mechanical Fasten TPO Hot air Welding TPO Detailed Spots Strengthening Test Check 3. Installation 1) Clean the litters,dust on the substrate 2)Pave a layer of PE film,the overlap uses butyl adhesive tape to glue 3)Pave Extruded polystyrene foam insulation board(XPS),using exclusive fasteners to fasten the board 4)Pre-applied TPO membrane: Lay the TPO membrane on the insulation board in accordance with the snap line,paving direction should be perpendicular with the wave of profiled steel sheet,dispose the loose TOP membrane as the outline on the insulation board. Membrane remains flat and even,overlap is 12cm and appropriate trim is needed 5)Fasten the TPO membrane: Align edge of mark line 30mm install the fasteners and elastics 6)Membrane Overlap: One piece membrane laid on the other,use the automatic hot air welding machine to weld 7) Detailed Spots Strengthening: Trim adequate TPO membrane for detailed spots,use portable hot welding machine weld on the TPO membrane 8)TPO membrane edge treatment: Use batten to fasten the edge along with sealants
Thermoplastic Polyolefin (TPO) is a kind of polymer waterproof membrane. It can be reinforced with polyester felt and fiberglass with non-woven fabric backing, manufactured by advanced extrusion machining technology. 1)Itâ??s easy to install with good system integrity, few accessories. 2) Excellent tensile strength, tearing resistance and penetration resistance performance. 3) No plasticizer, They have been tested as having excellent resistance to thermal aging and ultraviolet, durable and exposed. 4) Hot welding. The peel strength of joint is high. 5) Fast welding speed. 6) Environment friendly, 100% recycled, without chlorine. 7) White-based light -color and smooth surface with high refection, energy saving and anti-dust function.
I am Beijing Nimble bitumen membrane equipment CO.LT.We are mainly specialized in research,development and manufacture of equipment for bitumen membrane.Our company was established in 1991.It acts as the leading supplier of equipment for bitumen membrane in China, and a newborn force in international equipment industry for bitumen membrane.Beijing Nimble waterproofing membrane Corporation had focused on offering quality goods and on-time service,We can according to customer requirement to produce different types equipment from the small equipment to ten million ©O . Until now, we had served hundreds of customer from more than 10 countries in the world. Our equipment has exported to India,Russia,UKrine,Saudi Arabia ,North Korea,and We have a branch company In India now. ART 1 General information Technical parameters 1Production capacity: annual production of modified bitumen membranes of 3 million Sqm (16 hours/day, 300days/year with two shifts) Reinforcement: Polyester, Glass fibre Modified materials : SBS, APP 4Materials for surface: sand, scraps of stone, PE membrane, aluminum foil, etc. 5Specification of products: Width: 1m, thickness: 2-5mm, length: 7.5 or 10m 6Production speed: 0-20m/min¡£ 7Main workshop: 60¡Á (12-15) ¡Á£¨6-8£©m Labor required 5-7 workers are needed for the whole production line Boiler room: 2workers Modified workshop: 1-2 workers Production workshop: 2-3 workers Utilities Electricity: Alternating current, 380V50Hz60Hz Water Consumption: 2-3 T/D
