Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
Supplier: Electrical materials, electrical equipments, lighting fixtures, plumbing materials, ac materials, it materials, ceiling materials, partition materials, painting materials, floor tiles, hardware materials, hand tools & power tools, garage tools, wooden & carpenter materials, batteries. medical equipment and medical consumable product and medical surgical equipment.
Theaoson water-based spray paint is composed of aerosol cans, aerosol valves, paint and spray agent. It is widely used in the following fields: repairing paint defects, molds, industrial machinery, buildings, steel structures, advertising, marking, graffiti and so on. Features 1.Fast drying 2.Colorful and easy to use 3.Full paint film and high gloss 4.Strong adhesion Application It is suitable for metal, wood, clay bricks, glass, asbestos tiles, plastics, ceramics and other materials. Due to the diversity of materials during the specific construction, a small-scale test spray must be performed first, and no large-scale construction can be conducted after no adverse reactions
Theaoson zinc coating spray is composed of aerosol can, aerosol valve, paint liquid and propellant. This product uses bright silver powder imported from Germany. The color of the paint film produced after use has the same high-gloss galvanized color as the galvanized parts, it has the same color as the galvanized color that fades with the exposure time, so that there is no color difference in the repaired part coated on the galvanized part. Features High-gloss bright zinc Color consistent with galvanized parts Good atomization, easy to use Application It is suitable for color changing and anti-corrosion treatment of stainless steel, carbon steel, galvanized parts and other metal parts. Base material to prepare Clean the oil, dust and water stains thoroughly before use, and polish or spray primer on the base material if necessary. Instructions: Before use, you must shake up, down, left, and right, and continue to shake the can for about 1 minute after hearing the sound of glass to ensure that the paint liquid is fully mixed and even. 15 ~ 30cm away from the surface of the object to be sprayed, press the nozzle with the index finger to spray uniformly back and forth. When a small amount of remaining liquid cannot be sprayed, please rotate the nozzle 180 �° and spray again. If spraying is not finished one time, put the can upside down before storage, press the nozzle for about three seconds, and clean the nozzle to prevent plugging. Ending working After spraying, it should be placed in a clean and ventilated environment for about 12 hours. If it is not sprayed, the remaining material needs to be kept away from the light, and avoid being near fire sources. The solution of normal problem 1. Paint film whitening: It is recommended to avoid rainy days (especially high temperature and high humidity) and the next day after continuous rain. 2. Shut up: shake evenly and spray for 3 seconds or change nozzle. 3. Spray up: low temperatures suggest using 50 â?? warm water to heat up, one-time finish spray, spray avoid angle 45 degrees. 4. Flow: use the correct spraying distance (15-25cm) and spray movement speed (30-60cm/s) to avoid a thick spray. 5. Bite bottom: remove the bottom part of the bite, fill the bottom ash, and then spray the paint after the coating is dry and flat. Attention Keep away from children, please work in the air. If swallowed, you should immediately cause vomiting and seek medical advice. Spray must be kept in aerosol cans are vertical and horizontal angle of no less than 45 �°. Flammable, pressure vessel, do not use near fire source. The weight changes over time, which is normal, and the attrition rate is less than 2%/ year.
Supplier: Powder coatings and spray paintings
RITVER spray paint is anti rust protective coating available in all Ritver color shades. Available in 400ml/275gms, 12 pieces in a carton. Ritver is a Italian technology manufactured in UAE.
RITVER spray paint is anti rust protective coating available in all Ritver color shades. Available in 400ml/275gms, 12 pieces in a carton. Ritver is a Italian technology manufactured in UAE.
This primer is designed to be used as the strong base coat to ensure the perfect adhesion of all enamel spray on diffi cult surfaces such as metal alloys and metals. It protects metal surfaces from rust. Also suitable as a fi ller in bodywork car sector for small imperfections and scratches. Clean carefully the surface before application and shake vigorously the can. For overcoating are required at least 24/48 hours. After use, it's advisable to spray for 2/3 seconds with the can upside down to avoid the block of the nozzle. Sku:V400PRIMER
This paint is designed to be used as the base coat for a fi nishing enamels. It provides a strong base to ensure the perfect adhesion of the enamel spray on difficult surfaces such as plastics and metals. It protects metal surfaces from rust. On cars it covers small imperfections and scratches. Clean carefully the surface before application and shake vigorously the can. It dries on touch in roughly 15 minutes and dries fully in roughly 22 hours. For overcoating are required at least 24/48 hours. After use, it;s advisable to spray for 2/3 seconds with the can upside down, to avoid the block of the nozzle. Sku:V400PAST
