We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.
Standard Technique Surface finish Grade Thickness Width*Length JIS Aisi ASTM DIN EN bs Hot rolled No.1 201, 202, 301, 304, 304J1, 304L, 321, 316, 316L, 309S, 310S, 317L, 409L, 410, 410S, 420J1, 420J2, 430, 444, 441, 436, 439, 904L, 2520, 2205, 2507 etc 4.0mm-16mm,17-150mm 1250*3000mm(4.1*10ft) 1500*3000mm(5*10ft) 1250*6000mm(4.1*19.6ft) 1500*6000mm(5*19.6ft) 1800*6000mm(5.9*19.6ft) 2000*6000mm(6.5*19.6ft) Cold rolled 2B 201, 202, 301, 304, 304J1, 304L, 321, 316, 316L, 309S, 310S, 317L, 409L, 410, 410S, 420J1, 420J2, 430, 444, 441, 436, 439, 904L, 2520, 2205, 2507 etc 0.2mm-3.0mm 1000*2000mm(3.2*6.5ft) 1219*2438mm(4*8ft) 1500*3000mm(5*10ft) 1800 available 2000 available No.4 Hairline 8K BA Hot rolled or cold rolled embossed similar to the above info. colored Customized We can customize surface treatment, grade, thickness, width, length etc according to customer\'s requirements. Send us inquiry to get cost-effective price and details within 1 hour. Chemical Composition Mechanical Character Grade C Si Mn P S Ni Cr Mo Cu N Hardness 201 0.15 1 5.50-7.50 0.045 0.03 3.50-5.50 16.00-18. 00 ? 0.05-0.25 HB 241, HRB 100, HV240 304 0.08 1 2 0.045 0.03 8.00-11.00 18.00-20. 00 HB 187, HRB 90, HV 200 310s 0.08 1.5 2 0.045 0.03 19.00-22. 00 24.00-26. 00 HB 187, HRB 90, HV 200 316L 0.03 1 2 0.045 0.03 10.00-14. 00 16.00-18. 00 2.00-3.00 HB 187, HRB 90, HV 200 321 0.08 1 2 0.045 0.03 9.00-12.00 17.00-19. 00 HB 187, HRB 90, HV 200 430 0.12 1 1 0.04 0.03 (b) 16.00-18. 00 HB 183, HRB 88, HV 200
Taian Henson Metal Co lTD 420J2 Stainless Steel Strip For Razor Blade 201 j3 stainless steel strip CR Stainless Steel Coil Stainless Steel Strip 201 stainless steel strip price Sus ss420 420j1 ss420j2 stainless steel strip ASTM SS 201 202 301 304 304L 309S 316 316L 409L 410S 410 420J2 430 440 Stainless Steel Strips/band/Belt/Coil Factory Price 420j1 420j2 Stainless Steel Coil Strip Factory In Stock For Sale 420J2 1mm Thickness Stainless Steel Strip Bright Mirror Finished Surface 420j2 Stainless Steel Coil/Sheet/Strip for Blade Razor Modified 420 420J2 Stainless Steel Divider Strip For HDD Components Stainless Steel strap02mm 4mm Thick 14404 420j2 309s Brush BA Price Stainless Steel Strip For Razor Blade 401 406 410 420J2 good price ASTM 201 202 301 302 304 304L 309S 316 316L 2304 254Mo 409L 410S 410 420J2 430 440 Stainless Steel Strips/band/Belt/Coil
J series of 201 stainless steel | J1, J2, J3, J4, J5 J1: The carbon content is slightly higher than J4, and the copper content is lower than J4. Its processing performance is not as good as J4 material. It is suitable for ordinary shallow deep drawing and large angle deep drawing products such as decorative panels, bathroom products, sinks, and product pipes. J2, J5: Decorative tubes are easy to process, high hardness (both above 96�°), polished and beautiful, but they are easy to burst when used for square tubes or curved tubes (90�°). In terms of flat panel, due to its high hardness, the surface of the panel is more beautiful, and surface treatment such as frosting, polishing, and color plating can be carried out. But the biggest problem is bending, bending is easy to break, planing is easy to burst, so the ductility is not good. J3: High carbon, low chromium and low copper, but because of its high carbon content and low copper content, the material is slightly harder, so it is not suitable for bending with a slightly stronger strength. Compared with 201 stainless steel J1 material, the ductility is not so good, and it is easier to rust in the same environment. 201 stainless steel coil In the field of narrow bands, the emergence of 201 stainless steel J3 can better meet the requirements of pipe manufacturers for corrosion resistance and deformation. Because it can reduce the cost of raw materials for pipe manufacturers, it is sought after by pipe manufacturers in the narrowband field. J3 material is easy to process in veneer, but not difficult. The master of the processing factory said that he used J3 material to bend the board, and there would be an inner seam after it was broken (for black titanium, color board series, sanding board, when it is broken apart, there will be an inner seam when folding). The material of the sink has been bent 90 degrees, and it will not work if it continues. J4: The material of J4 is a relatively high-end variety in the J series of 201 stainless steel. It is suitable for deep drawing products with small angles. Most of the products that need deep drawing and salt spray test will choose it. Such as sinks, kitchen utensils, bathroom products, kettles, thermos cups, door hinges, pots, etc.
Stainless Steel Coils
Stainless Steel Strip The properties of stainless steel are corrosion resistance, high ductility, attractive appearance and low maintenance. Stainless steel contains chromium which provides the properties of corrosion resistance at high temperatures. Stainless steel can withstand corrosive or chemical environments due to its smooth surface. Stainless steel products are safe for long-term use with excellent resistance of corrosion fatigue. Other specifications are also available up to request Hot Rolled Strip Available Size Width: 16.0~609.6 mm Thickness: 2.5~10.0 mm Available Steel Grade: 304, 304L, 316L Surface Finish: No.1 Cold Rolled Strip Available Size Width: 4.0~609.6 mm Thickness: 0.1~3.0 mm Available Steel Grade: 201, 202, 204 Cu3, 301, 304, 304L, 310S, 316L, 321, 409L, 410S, 420J2, 430, 439, 441, 444, 445 Surface Finish: 2B, 2D, BA, No.3, No.4, No.5, SB, HL
Product Stainless Steel coil Surface Finish 2B, BA, NO.1, NO.4, 8K, HL, Embossing, Satin, Mirror, ect Technique Cold Rolled, Hot Rolled Steel Grade 200 series: 201 202 300 series: 301 304 304L 309 310 310s 316 316L 321 400 series: 409 410 410S 420 430 439 443 Duplex:3RE60(Cr18) SAF2304 (Cr23)SAF2205 (Cr22) SAF2507(Cr25) Color Golden, Black, Sapphire Blue, Brown, Rose Gold, Bronze, Silver, ect Processing Type Cutting, bending,stamping,welding,cnc machining Cutting Type Laser cutting;water-jet cutting;flame cutting Application Interior Exterior decoration, Architecture; Evevator; Kitchen, Ceiling, Cabinet, Advertising nameplate, Roof structure, Lead Time 7-15 working days
Taian Henson Metal Co lTD 420J2 Stainless Steel Strip For Razor Blade 201 j3 stainless steel strip CR Stainless Steel Coil Stainless Steel Strip 201 stainless steel strip price Sus ss420 420j1 ss420j2 stainless steel strip ASTM SS 201 202 301 304 304L 309S 316 316L 409L 410S 410 420J2 430 440 Stainless Steel Strips/band/Belt/Coil Factory Price 420j1 420j2 Stainless Steel Coil Strip Factory In Stock For Sale 420J2 1mm Thickness Stainless Steel Strip Bright Mirror Finished Surface 420j2 Stainless Steel Coil/Sheet/Strip for Blade Razor Modified 420 420J2 Stainless Steel Divider Strip For HDD Components Stainless Steel strap02mm 4mm Thick 14404 420j2 309s Brush BA Price Stainless Steel Strip For Razor Blade 401 406 410 420J2 good price
Materal stainless steel ASTM BS EN JIS Grade 201 1.4372 SUS 201 Thickness 1.0mm Width 1220mm Length 800mm Surface 2B
PRODUCT:Stainless Steel coil/foil/roll strip band BRAND: HENSON GRADE:201.202.301.302.304.304L.310S.316.316L.321.430.430A.309S. 2205.2507.2520.430.630.631 ..410.440.904Lect. Or Customized LENGTH As Customer requirements SURFACE No.1, 2B, BA, 8K Mirror, Hairline,satin, Embossed,brush, No.4,HL,matt,pvc film,laser film. STANDARD:GB, AISI, ASTM, ASME, EN, BS, DIN, JIS PACKAGE: Standard export sea-worthy packing or customized MOQ:1Ton
