Supplier: Agricultural products (coffee, rice, black pepper, cocoa, cashew nuts, etc.) garment/ medical product (non woven coveralls, gowns, medical facemask, arm cover, cap, shoes cover, bra, felt suit, towel, labor protection product) plastic products, pe tarpaulin, pvc tarpaulin, jumbo bag, pp bag, rubber products
Supplier: Tarpaulin, tarp, pe tarp, frp, grp, grating, pultruded, composite, frp rebar, panel tanks, pond liner, geomembrane, junction box, truck cover, boat cover, tent, camping
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
We are manufacturer of FRP Based Manhole covers made with GERMAN MBT technology. for superior finish, long life and durable..for further details .
FRP Manhole Cover DIa 600 - D400 Everlast brand FRP Covers and Gratings are manufactured using the best quality materials and state- of-the-art technology. Each Product is rigorously tested to adhere to exacting quality standards.
FRP Manhole Cover DIa 600 - D400 Everlast brand FRP Covers and Gratings are manufactured using the best quality materials and state- of-the-art technology. Each Product is rigorously tested to adhere to exacting quality standards.
With a better performance than Cast Iron, Ductile Iron and RCC manhole covers, this product is an industrial revolution. They have been thoroughly tested as per BS EN 124 1994 & AASHTO M306 standards for drainage and utility services. Thermodrain manhole covers meet all the requirement of the code. Our covers are available in all standard sizes with load bearing capacity ranging from 1.5 tons(A 15) to 40 tons(D 400). They are circular, square and rectangular shapes available with single and double sealed arrangements. Locking arrangement on the cover is also available on request. All the sizes of manhole covers are available in the following load bearings. 1. 5 tons (A 15) / 2.5 tons / 5 tons / 10 tons / 12.5 tons (B 125) / 20 tons / 25 tons (C 250) / 40 tons (D 400).
With a better performance than Cast Iron, Ductile Iron and RCC manhole covers, this product is an industrial revolution. They have been thoroughly tested as per BS EN 124 1994 & AASHTO M306 standards for drainage and utility services. Thermodrain manhole covers meet all the requirement of the code. Our covers are available in all standard sizes with load bearing capacity ranging from 1.5 tons(A 15) to 40 tons(D 400). They are circular, square and rectangular shapes available with single and double sealed arrangements. Locking arrangement on the cover is also available on request. All the sizes of manhole covers are available in the following load bearings. 1. 5 tons (A 15) / 2.5 tons / 5 tons / 10 tons / 12.5 tons (B 125) / 20 tons / 25 tons (C 250) / 40 tons (D 400).
Material: PE, PVC Roll: 1.82 x 100 m; 0.92 x 100 m Sheet: 10 x 10 m ; 3.6 x 5.4 m Quantitative: # 1000 ; # 3000 Color: Blue Packing: dup-rolls (Rolls); OPP Bag (Sheets) Details: eyelets Other: OEM
