DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Epoxy Resin
Product’s name: Injection mold Keyword: Injection mold,blow molding, rotary mold, roto mold. Specification: We offer to make molds for injection molding, blow molding, rotary molding roto molding. We also undertake injection, blow or rotary molding works from Toys to Big bins or water tanks, floating docks, road barrier etc. We can do custom design plastic parts or components. Water Tanks ( Roto Molding process)
Jerry Can ( Blow molding Process) Keyword: Injection mold,blow molding, rotary mold, roto mold. Specification: We offer to make molds for injection molding, blow molding, rotary molding roto molding.
Plastic Floating Dock ( Blow molding process) Keyword: Injection mold,blow molding, rotary mold, roto mold. Specification: We offer to make molds for injection molding, blow molding, rotary molding roto molding.
Road Barrier ( roto Molding Process). Keyword: Injection mold,blow molding, rotary mold, roto mold. Specification: We offer to make molds for injection molding, blow molding, rotary molding roto molding.
Rectangular Bin (Roto Molding process) Keyword: Injection mold,blow molding, rotary mold, roto mold. Specification: We offer to make molds for injection molding, blow molding, rotary molding roto molding.
Rectangular Bin( roto Molding Process) Keyword: Injection mold,blow molding, rotary mold, roto mold. Specification: We offer to make molds for injection molding, blow molding, rotary molding roto molding.
We purchase stems from farmers and suppliers as shown in pictures and we then cut them and clean them of foreign matter and we then bag them. We can provide with the following certificates, 1. Processing certificate. 2. SGS certificate. 3. Origin Certificate. 4. Phytosanitary Certificate. 5. USD 3.42/kg CIF China
Can supply: approx. 95% HDPE - approx. 5% PP GRIND (REGRIND) FROM CAPS MIXED COLORS IN BIG BAGS. Size 8-10mm. Post commercial. Clean. No foreign bodies inside. Can load in 1x40' HC container approx. 23 MT (10%) Ready for shipment. Photos available upon request. If you are interested kindly contact us for more information (price, available quantity etc.). You are welcome to visit our company premises and supervise our materials. Certificate ISO: 9001, ISO: 14001, OHSAS 45001, AQSIQ and CCIC.
