Pipe fittings are the general names of parts and components that play the role of connection, control, direction change, diversion, sealing and support in the pipeline system. Steel fittings are pressure fittings. According to the different processing technology, it is divided into four categories, namely, butt welding pipe fittings (divided into weld and no weld), socket welding and threaded pipe fittings, flange pipe fittings.
According to the application:
1. pipe fittings for connecting pipes are: flanges, live joints, pipe hoops, clamps, clamps, throat hoops, etc.
2. changing the direction of the pipe: bends, bends.
3. pipe fittings changing pipe diameter: variable diameter (different diameter pipe), different diameter elbow, branch pipe table, reinforcing pipe.
4. pipe fittings with additional piping branches: three links, four links.
5. pipe fittings for pipe sealing: gasket, raw material belt, thread, flange blind plate, pipe plug, blind plate, head, welding plug.
6. pipe fittings for pipe fixing: clasp, hook, ring, bracket, bracket, pipe clamp, etc.
According to the connection :1, welded pipe fittings 2, threaded pipe fittings 3, clamping pipe fittings 4, clamping pipe fittings 5, socket pipe fittings 6, rubber ring connection pipe fittings
According to the material divided into 1, cast steel pipe fittings 2, forged steel pipe fittings 3, alloy pipe fittings 4, stainless steel pipe fittings.
Pipe fittings are widely used in municipal, petrochemical, west-to-east gas transmission, ships and nuclear power.
* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
Supplier: Manufacturers, exporters & importers of stainless steel / copper / brass / aluminium / duplex steel / carbon steel / alloy steel in shape of pipes, tubes, flanges, pipe fittings,round bar, bright bars, angle bar, flat bar, hex bar, square bar, sheets, coils, strip, plates, wire, tie wire, strip banding, decorative tubes / pipe, valves, threaded fittings,forged fittings etc. in any shape / size / grade.
also specialised in high nickel alloys like inconel, monel, titanium, hastalloy etc. in any size / type / grade & as per drawing. Services: Manufacturers, exporters & importers
Product Details:
Size 3 inch, 2 inch, 1/4 inch, 1 inch, 3/4 inch, >3inch
Connection Flange, Male, Female, Welded
Material TITANIUM
Application Hydraulic Pipe, Gas Pipe, Structure Pipe, Chemical Fertilizer Pipe
Elbow Bend Angle 90 Degree, 180 Degree, 45 Degree
I Deal In New Only
Metal Aids India, are one of the leading manufactures & suppliers of Titanium Forged Elbow.
Grade:-
Titanium Gr 1, Gr 2, Gr 3, Gr 4, Gr 5.
Dimensions
ANSI/ASME B16.11 & BS3799, etc.
Class:-
2000LBS, 3000LBS, 6000LBS, 9000LBS, etc.
Type:-
Socket Weld (S/W) & SCREWED (SCRD) â?? NPT, BSP, BSPT
Types of Titanium Forged Fittings : â?º Forged Threaded Elbow
â?º Forged Threaded Equal & Unequal Tee
Product Details
Size 3 inch 2 inch 14 inch 1 inch 34 inch 3inch
Connection Flange Male Female Welded
Material TITANIUM
Application Hydraulic Pipe Gas Pipe Structure Pipe Chemical Fertilizer Pipe
Elbow Bend Angle 90 Degree 180 Degree 45 Degree
I Deal In New Only
Metal Aids India are one of the leading manufactures suppliers of Titanium Forged Elbow
Grade
Titanium Gr 1 Gr 2 Gr 3 Gr 4 Gr 5
Dimensions
ANSIASME B1611 BS3799 etc
Class
2000LBS 3000LBS 6000LBS 9000LBS etc
Type
Socket Weld SW SCREWED SCRD NPT BSP BSPT
Types of Titanium Forged Fittings Forged Threaded Elbow
Forged Threaded Equal Unequal Tee
We are exporters of stainless steel socket weld fittings like elbow, tee, reducer, cross, coupling, cap, union etc. in grade F347, F347H, F321, F321H, F310, F309, F317L, F51, F53 etc.
Metal Aids India a accredited with AN ISO 9001: 2015, 14001: 2015, OHSAS 18001 & PED Certified Company and was established in since 2010. We take the pleasure to introduce ourselves as a largest Manufacture & Exporter of all type of industries products like Seamless & Welded Elbow, Tee, Reducer, Clamp, Cap in different
shape & size (as per client drawing & specification) etc.
Product Specification: UNS 32750 Duplex Elbow
Specification: ASTM / ASME
Size: 1/2\" To 48\"NB & OD (Welded Thk: 1MM to 40MM)
Seamless Thk: Sch10, Sch 30, Sch 40, Sch 60, Sch 80, Sch 160
Type: Elbow (Short & Long Elbow),90 Deg Elbow, 45 Deg Elbow.
Form: Seamless & ERW (Welded)
Grade:
Duplex & Super Duplex: UNS 31803, UNS32205 (F51), UNS 32750
(F 53), UNS 32760 (F 55), UNS 31254 (SMO. 254)
Product Details:
Material SS
Size 3/4 inch, 1 inch, 3 inch, 1/4 inch, >3inch, 2 inch
Connection Welded
Elbow Bend Angle 45 Degree, 180 Degree, 90 Degree
Application Gas Pipe, Structure Pipe, Chemical Fertilizer Pipe
Thickness Sch 20, Sch 40, Sch 80
Country of Origin Made in India
We are stockist & manufacturers of Long radius, short radius Elbow 45 degree, 90 degree, 1D, 2D, 3D in various grades like 304 / 304L / 316 / 316L / 904L / 310 / 317L in both semaless and welded as per customers requirement.
