APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Two component, acrylic aliphatic polyurethane coating. Offers excellent gloss and colour retention. It is used for subtracts as steel, aluminum, glass-fiber, plywood etc.
Price of transparent white mineral oil #15 food grade How to use: Because it have special and excellent physical and chemical function, it can be used in many different industries: 1. Cosmetic industry for skin care cream, bath gel, shampoo and other cosmetic formulations with excellent softness and silky feel. 2. Rubber, plastic, latex, polyurethane, light industry: as a model release agent, brightener agent and release agent Dosage: Depending on the application conditions, the concentration is from a few PPM up to 100% range. Note: With a high concentration of acid or alkali substances and Lewis acid has a tendency to degrade volatile exposure, the higher the temperature of the reaction is more obvious. Low concentration in contact with strong acid or alkali at high temperatures or prolonged action of the viscosity tends to become larger until cross -linked. Specification price of transparent white mineral oil #15 food grade Article 201-10 201-20 201-50 201-100 201-200 201-350 Viscosity(25)mpa.s 10±2 20±4 50±5 100±5 200±10 350±10 Flash point() 160 210 270 310 310 310 Density(25)g/cm3 0.930-0.940 0.945-0.955 0.955-0.965 0.960-0.970 0.962-0.972 0.965-0.975 Volatile(150,3h)% 3 2 1.5 1 1
Product Name: 1,2-Propanediol INCI Name: PROPYLENE GLYCOL Molecular Formula: C3H8O2 Molecular Weight: 76.09 Appearance: Viscous Liquid Purity: 99% CAS NO.: 57-55-6 EINECS No.: 200-338-0 Supplier: ZHENYIBIO Propylene glycol is used for similar applications as other glycols. Propylene glycol is an important raw material for unsaturated polyester, epoxy resin, and polyurethane resin. The use amount in this area accounts for about 45% of the total consumption of propylene glycol. Such unsaturated polyester is used extensively for reinforced plastics and surface coatings.
INTRODUCTION The product is a high molecular 30 TBN Calcium Sulphonate. The increased oil solubility of the organic portion of this Sulphonate enables the product to provide rust protection and acts as a dispersant for graphite and molybdenum disulfide. It can be used as an additive in lubricating oils, greases, rust inhibition, antiwear and hydraulic fluids. SPECIFICATION Test Method Minimum Maximum Appearance Visual Brown liquid Brown liquid Colour ASTM D 1500 2 5 Sp. Gravity @ 15.6 C ASTM D 1298 0.95 1.05 Flash Point C (COC) ASTM D 92 175 - Viscosity @ 100 C, cst ASTM D 445 40 70 Avg. Molecular wt. ASTM D 3712 1000 1100 TBN (mg KOH/gm) ASTM D 974 28 35 Calcium Content %[w/w] GL EDTA 1A 2.8 3.0 FORMULATION The product is recommended for use at 0.5% to10.0%wt. In suitable base stocks to provide detergency & anti-rust performance characteristics to oils. It is compatible with mineral base oils, white oils, and synthetic base stocks. APPLICATION Imparts excellent rust prevention, detergency and Anti oxidant Properties. Corrosion inhibitor in mill oils, short-term rust preventatives, coatings and greases. Dispersant and corrosion inhibitor in engine oil. Provides excellent resistance to coated Cold Rolled Steel for antirust applications. Works in extremely hostile conditions like highly acidic environment as well as highly humid atmosphere. It is non-staining having detergent, dispersant properties. Environmental Friendly, Biodegradable without side effect. HANDLING AND STORAGE Calcium Sulphonate is normally handled at room temperature. For general purposes, the following storage and handling temperatures are recommended: Storage Handling 50-70C (122-158F). For more extensive information on the safe handling and use of this product, see the Material Safety Data
Powder Glue, construction adhesive heat resistant tile adhesive Porcelain Tile Adhesive is also known as the ceramic tile or ceramic tile adhesive glue, points type, polymer type, heavy brick, is a newly developed products, mainly used for stickup ceramic tile, brick, tile and other decorative materials, widely used in internal and external walls, floor, bathroom, kitchen, and other places of building the veneer of decoration. 1.Product Description: Product Name : BE GOOD Strong Adhesion� Tile Adhesive Type : Strong Adhesion Type Color : Grey / White Package : 20kg/bag Application : Tile Adhesive Reference Usage : 2-5kg/ m Mixing Ratio Powder : Water = 20kg : 5 liters Pot Life : 4 hours Application Temperature : 5 - 40 Packaging Details: 20kg/bag / 72bags/pallet / 20pallets/20GP /1360 bags/1*20GP Payment: TT Delivery date: 10 to 15 working days. Original country: China 2. Features 1) Strong adhesion and elasticity. 2) Pasting layer is thin and even, and hardly with hollowness. 3) Easy and simple application, no need to pre-moisturize the bricks and walls. 4) Excellent waterproofing performance. Adoption of scraper method will speed up the tiling. 3. Application Range 1) Suitable for interior and exterior use.� 2) Suitable for substrate made from concrete, masonry, pre-cast material and lightweight brick. 3) Suitable for walls, floors and roofs of architects, such as tunnels, bridges, basement, kitchen, bathroom, balcony, swimming pool and reservoir and so on. 4) Suitable for architects with structure which might easily vibrate and split, such� as post-cast strip, pipe orifice.
Sebacic acid has a wide range of uses, mainly used to prepare sebacic acid esters, such as dibutyl sebacate, dioctyl sebacate and Diisooctyl sebacate. These esters can be used as plasticizers for plastics, cold resistant rubber, polyamide, polyurethane, alkyd resin, synthetic lubricating oil, lubricating oil additives, spices, coatings, cosmetics, etc. It can also be used as raw material for the production of nylon 1010, nylon 910, nylon 810, nylon 610 and nylon 9, and as raw material for high temperature resistant lubricating oil diethylhexyl ester. It is also the raw material for the production of plasticizer, softener and solvent for alkyd resin (used as surface coating, plasticized nitrocellulose coating and urea resin varnish) and polyurethane rubber, cellulose resin, vinyl resin and synthetic rubber. Hot selling Sebacic acid Decanedioic Acid with new batch CAS 111-20-6
Laxogenin is a plant based steroid. It can be found in small quantities of green (plant based) foods. It is derived from a certain plant (smilax sieboldii) and promotes anabolic activity within the body.But no side effects or potential health risks is found yet. More information of Isophorone CAS:78-59-1 1)Used as an intermediate in manufacturing mainly polyurethane field compounds such as isophorone Diamine, isophorone Diisocyanate, Trimethylcyclohexanone used for Light stable weather resistant urethane coating. 2)It is used as a solvent for resin, lacquers,inks & PVC. 3)It is used in formulating Pesticides, Herbicides. 4)It is used in vinyl chloride/acetate-based coating systems for metal cans, other metal paints,nitrocellulose, and printing inks for plastics.
Products Description Adipic acid is an important organic dibasic acid with the structural formula HOOC(CH2)4COOH. It can undergo salt-forming reaction, esterification reaction, amidation reaction, etc., and can be polycondensed with diamine or diol to form high molecular polymer. Adipic acid is an industrially important dicarboxylic acid. It plays an important role in chemical production, organic synthesis industry, medicine, and lubricant manufacturing. Its output ranks second among all dicarboxylic acids. Application 1. Adipic acid is mainly used in the production of nylon fibers and engineering plastics. 2. It is also widely used in the production of polyurethane and other esters, most of which are used in the production of PU, shoe sole slurry, polyurethane foam, etc., and a small part is used as advanced lubricating oil. 3. Higher esters of adipic acid can be used as plasticizers for polyvinyl chloride and its copolymers, and natural synthetic rubber. 4. A large amount of adipate is used in polyvinyl chloride for food packaging, film and insulation. 5. Adipic acid is also used as an acidulant for various foods and beverages.
