APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Fertilizers play a key role in improving the productivity of various crops. Fertilizers contain three primary elements. They are nitrogen (N), phosphorous (P) and potassium(K). They are usually represented on the package as a percentage of their weight i.e. 10-8-6 meaning 10% of N, 8% of P and 6% of K. Formulation percentages vary depending on intended use and desired effects.
Physical presentation : Crystal Color : Off-white Percent % : 21% Application : Landscaping.
Physical presentation : Granular Color : Grey Percent % : 12-12-17+1MgO Application : Direct application.
Building and Construction Material
Supplier: All food products, fruits, cereals, sona masoor rice, basmati rice, turmeric, pigeon pea, cardamom, coconuts, construction materials like granite, cement, fly ash, iron, steel, electronic goods and automobiles etc.
Services: Packing, transportation, quality checking, laboratory testing reports, weights and measurement reports.
Buyer: Iron, steel, electronic goods, scrap, automobiles, eateries, all food products, fruits , cereals, sona masoor rice, basmati rice, turmeric, pigeon pea, cardamom, coconuts, construction materials like granite, cement, fly ash.
Supplier: Rice, corn, sugar, wheat, cement, aluminum ingots, copper scrap , used rail and hms 1&2, urea, sulphur, cooking oils, petroleum products, aviation fuel, mazut, millet, alfalfa grass, timber logs, teak wood, wood pallet
Buyer: Steel scrap, used rails, cement
Supplier: Shampoo, soap, toothpaste, shaving razor, hand body lotion, household cleaning products, coffee beans, instant coffee, coffee mix, tea, chocco, biscuits, wafer, cookies, milk, candy, canned food
Services: Buying & sourcing agent
General Purpose Fresh Coir Block (Processed & Compressed Coir) Coir pith blocks ensure high oxygen levels and therefore good drainage properties. They reduce the dormancy period of seeds and promote early sporting in almost all flowering plants and vegetable crops, We can supply coir blocks as Fresh Coir Blocks for vegetables/fruits and High Drain Rose Mix Coir Blocks specially designed to be used with Roses. Can be supplied in different weights, sizes or as per buyer’s requirements. Please contact us for more details and price quotations Advantages of Fresh Coir Blocks: Designed for vegetable and fruit plants Faster binding of soil Resistant to mold & rot; no chemical treatments needed Great air and water permeability Holds the seeds/saplings in place Excellent medium for quick vegetation No removal costs; Naturally degrades over a period of 2 to 5 years time Promotes deep rooting of plants Provides nutrients Easy to install Eco-friendly We can make 5 kg and 15 kg blocks.
