Performance Power 0.75kW Application Limits 1. Maximum liquid temperature +35 �°C 2. 200 m immersions limit 3. Starts/ hour 24 at regular intervals 4. Minimum flow rate for motor cooling 8 cm/s 5. Continuous service S1 Electric Motor 1. 2 pole electric motor, 50 Hz (n~ 2900 rpm) 2. Voltage: * Single phase 210- 220- 230 V 3. Insulation: class F 4. Protection: IP 68 Construction and Safety Standards 1. Oil filled rewindable motors (non-toxic oil use with food) 2. Jacket: AISI 304 stainless steel 3. Shaft: AISI 304 stainless steel 4. Dimensions of the flange connection in compliance with NEMA standards. 5. Chamber: Cast Iron 6. Complete with power cable of the following length: a. Single phase: 0.55- 1.1 kW = 4x1.5 mm / 1.5 mt. 1.5- 2.2 kW = 4x1.5 mm / 2.5 mt. 3.0 kW = 4x2.5 mm / 3.0 mt. b. Three phase: 0.75- 1.5 kW = 4x1.5 mm / 1.5 mt. 2.2- 4.0 kW = 4x1.5 mm / 2.5 mt. 5.5- 7.5 kW = 4x2.5 mm / 3.0 mt. Available on request 1. Other voltages or 60 Hz. frequency 2. Brass Top Bearing Cover
Submersible Pumps & Motor Set Wide Range Of Submersible Pumps, Openwell Pumps, Centrifugal Monoblock Pumps, Self Priming Pumps Available. All Running Models Are Available With ISI & Star Rating Marks.
Supplier: Pumps, motors, submersible pumps, submersible motors, submersible pumps, submersible motors
Multi Stage Centrifugal Pump With Radial & Mixflow Impeller It Operate Submerged Beneath The Surface Of Water Prime Mover Motors Are Wet Type, Water Lubricated Easy installation And Easy Servicing It Also Works On Low Voltage Energy efficient design Good Quality Components And Parts Require, less Maintenance 50 feet head per stage pumps are design for hihg head application Janta model pump design for 6 motor & 7/8 pump for high discharge application at low cost MOTOR BODY : Stainless Steel with 1% Nickel STAMPING : Electrical Grade Silicon Steel Sheet with 3.9 to 4.5 Watt loss/hour THRUST BEARING Stainless Steel 304 Tilting Pad Segment with Carbon Plate BUSH BEARING : G.M. LTB 4 ROTOR SHAFT : Stainless Steel 420 H&T SEAL : Nitrile Rubber Oil Seal WINDING : Poly Wrape Double Coated Copper Wire PUMP BOWL : Graded cast Iron PUMP SHAFT : Stainless Steel 410 IMPELLER : Stainless steel casted dynamicaly balanced PUMP SLEEVE : Stainless steel with hard chrome plating 50 FEET HEAD PER STAGE PUMP : Pump bowl stainless steel investment casting SINGLE PHASE : 180- 240V THREE PHASE : 300- 415V HEAD 4 Mtrs to 465 Mtrs CAPACITY : 45 LPM to 1200 LPM VOLTAGE : AC 180- 240 V (Single Phase), 300 – 415 V (Three Phase), 50 Hz, 2900 RPM NUMBER OF MODEL : More than 800 nos. ISI MODEL : More than 300 nos.
Nema Standerd Submersible Pumps And Motor Available 4" & 6" Submersible Motors & Pumps with NEMA Standerds. Available Customised Design For OEM Supply Also. SALIENT FEATURES: Easy To Install, Highly Efficient Motor & Pump, Law Power Consumption, Specially Design For Wide Voltage Range, Corrosion Resistance Stainless Steel Motor & Pump Body, Use Graded Varnish To Reduce Corrosion In Stator, Rotors Are Dynamically Balanced With More Than 2850 rpm To Reduce Vibration, Long Life And Negligible Maintenance Due To High Precision Work, Rotor Are Painted With Special Epoxy Paint For Prevent Corrosion Effect For Long Time, Noiseless & vibration free motors, All Parts Machined On CNC Machine Only
Technicial Specifications Class: F Frequency: 50 Hz. Outer Diameter: 192 mm Motor Power Range: 40 HP - 150 HP Axial load carrying capacity: 40HP-90HP motors and 45 kN 100HP-150HP motors 55 kN Based on 8" NEMA standards Starting : S/M Supply voltage : ~3, 380/415 V (-6%+10%) Motor protection: IP 68 (Mechanical Seal) Immersion Depth: Standard Upper Limit Working ambient temperature : Max. 30 C The coolant velocity passing around the engine is minimum 16 cm/sec. Usage Areas City Networks Drinking Water Wells Agricultural watering Geothermal Wells Seawater Transport FEATURES Provides cooling and lubrication with direct water without a cooling unit Motor mounting flange and shaft end conform to NEMA standard The motor body tube is AISI 304 motor shaft 420 stainless steel. The motors are standard steel sealed.
Salient Features Multi stage centrifugal pump with Radial & mixflow impeller It Operate Submerged Beneath The Surface Of Water Prime mover motors are wet type, water lubricated Easy installation and easy servicing It also works on low voltage Energy efficient design Good quality components and parts require less maintenance MOTOR BODY : Stainless Steel with 1% Nickel STAMPING : Electrical Grade Silicon Steel Sheet with 3.9 to 4.5 Watt loss/hour THRUST BEARING : Stainless Steel 304 Tilting Pad Segment with Carbon Plate BUSH BEARING: G.M. LTB 4 ROTOR SHAFT : Stainless Steel 420 H&T SEAL : Nitrile Rubber Oil Seal WINDING : Poly Wrape Double Coated Copper Wire PUMP BOWL : Graded cast Iron PUMP SHAFT : Stainless Steel 410 IMPELLER : Stainless steel casted dynamicaly balanced PUMP SLEEVE : Stainless steel with hard chrome plating HP 10.0 HP to 80 HP THREE PHASE 300- 415V HEAD 15 Mtrs to 280 Mtrs CAPACITY 300 LPM to 2400 LPM VOLTAGE - AC 300- 415 V (Three Phase), 50 Hz, 2900 RPM NUMBER OF MODEL More than 800 nos.
Salient Features : Multi Stage Centrifugal Pump With Radial & Mixflow Impeller It Operate Submerged Beneath The Surface Of Water Prime Mover Motors Are Wet Type, Water Lubricated Easy installation And Easy Servicing It Also Works On Low Voltage Energy efficient design Good Quality Components And Parts Require, less Maintenance 50 feet head per stage pumps are design for hihg head application Janta model pump design for 6 motor & 7/8 pump for high discharge application at low cost Motor Body : Stainless Steel With 1% Nickel STAMPING : Electrical Grade Silicon Steel Sheet with 3.9 to 4.5 Watt loss/hour THRUST BEARING : Stainless Steel 304 Tilting Pad Segment with Carbon Plate BUSH BEARING : G.M. LTB 4 ROTOR SHAFT : Stainless Steel 420 H&T SEAL : Nitrile Rubber Oil Seal WINDING : Poly Wrape Double Coated Copper Wire PUMP BOWL : Graded cast Iron PUMP SHAFT : Stainless Steel 410 IMPELLER : Stainless steel casted dynamicaly balanced PUMP SLEEVE : Stainless steel with hard chrome plating 50 FEET HEAD PER STAGE PUMP : Pump bowl stainless steel investment casting HP 2.0 HP to 30 HP SINGLE PHASE : 180- 240V THREE PHASE : 300- 415V HEAD : 4 Mtrs to 465 Mtrs CAPACITY : 45 LPM to 1200 LPM VOLTAGE : AC 180- 240 V (Single Phase), 300- 415 V (Three Phase), 50 Hz, 2900 RPM NUMBER OF MODEL : More than 800 nos. ISI MODEL : More than 300 nos.
Qj series submersible motor pump ííííqj series submersible motor pump is a kind of energy saving product which is designed according to national standard.It is widely used in farm mines, proving human beings and animals with drinking water in plateau of mountaionous district.The type of qj submersible motor pump operates under water consisting of qj submersible pump and yqs submersible motor.Outstanding features include tied construction, small and light, easier installation, use and maintenance, reliable and safe operation, high efficiency etc.
