Curing compound is a liquid coating applied to freshly poured concrete surfaces to promote hydration and ensure proper curing. It forms a membrane barrier that retains moisture, allowing the concrete to cure uniformly, minimizing cracking and enhancing strength and durability. The compound also prevents rapid moisture loss and surface evaporation.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Tiles Adhesive (CT-01),(02),(03), Tiles Epoxy Grout, Tiles Grout (Light Color), Tile Grout (Dark Color), Tiles Epoxy Grout Sparkle, Block Jointing Mortar, Wall Putty, Floor Hardener Non-Metallic, Tile Spacer (2mm, 3mm, 4mm,5mm), SBR. Etc. Products are available in stock.
* The cement is the most demanding and essential raw material used in various production and construction activities. The cement industry has witnessed a steady growth in the market as different range of products using cement are manufactured. It is a binder, a raw material substance that serves as an adhesive to other materials. Cement mixed with water and fine aggregate produces, sand and gravel to create concrete. It is the most-consumed resource and is widely available in the market. * Portland Cement is the most common type of cement used for concrete, mortar and stucco. Types Of Cement We offer include: Ordinary Portland Cement Portland Pozzalana Cement White Cement Portland Blast Furnace Slag Cement Applications * Cement is a very significant material for binding in various fields of construction. Some of the uses of cement include: * Concrete for laying moldings, floors, and roofs * Construction of lintels, beams, stairs, pillars, etc. * Mortar for plastering, masonry work, etc. * Use to build structures like fireproof and heatproof, hydrographic structures, chemical proof structures, bridges, etc. * Fire Proof or Heat Proof Structures * Used to manufacture precast members, piles, fencing posts, etc. * Use for making joints in drainage and pipes * Use for the construction of cement concrete roads, wells, water tanks, etc. Cement Quality * As a top construction material supplier, we supply the best quality of cement that gives high compressive strength in concrete, high durability and High Workability. * We supply the Required Grade and Type of Cement; that have been procured from the Top Brands made available to the customers at the required Specification for the best prices in the Bulk quantities required. Transportation * Cement is carefully packed in dry, clean and watertight to prevent solidification when wet. It is packed and shipped in Jumbo/Bulk/50 kgs paper sacks or one/two tone polypropylene bags. Further, bagged cement is packed with multilayer damp-proof and water-proof material to avoid any absorption of moisture and/or carbon-di-oxide. Temperature is thoroughly checked before loading the cement while transporting from the source-destination, or production site, it can be as high as 110C. * While transporting (both short and long distances), we take extra safety precautionary steps like waterproof, dust-proof, moisture resistant, and radiation-resistant bags.
Krs cladding board – a fibre cement board with high impact strength and moisture and fire resistant properties Krs fiber cement board is the perfect choice for building board applications such as wall cladding, wall partitioning and decorative walling. The types of buildings that are suitable for krs board applications are residential, commercial and industrial buildings as well as schools and hospitals; especially where speedy construction, cleanliness and hygiene is of high importance. Benefits of krs fibre cement board: weather resistant immune to water damage fire resistant provides sound insulation shatter resistant low shrinkage flexible high degree of workability termite resistant Matching the demands of modern applications Fiber cement board is a non-asbestos fibre-cement product composed of portland cement, cellulose fibre and refined sand. Using a special manufacturing process called autoclave, fiber cement board acquires the strength, durability of cement and easy workability of wood as well as dimensional stability. A non-combustible multi-purpose application fibre-cement flat board, fiber cement board comes with various thicknesses which are suitable for various applications; ceiling, wall, and floor. It can be used for both exterior and interior applications. Krs boards can perfectly be calibrated and then laminated or coated with other materials, such as eg. Wood veneer.
Supplier: Concrete admixtures, water proofing systems, industrial grouts, anti-corrosive coatings, protective and decorative coatings, concrete repair products, industrial floorings, concrete surface treatments, tile adhesives and joint fillers, joint sealant and vibration pad.
Services: We handle new installations / constructions apart from repair and revamping projects. Our services include:
òconsulting in selection of the right solution and products
òsupply of the materials
òinstallation services and execution
òproject management
Supplier: Curing compounds, admixtures, water proofing systems, industrial floorings, epoxy, sealants, concrete, tile adhesives, construction chemicals
Supplier: Grouting materials, grouting materials master batch, rapid hardened grout, epoxy grout, grouting resin injection glue, expansion agent, rapid hardened epoxy grout, coating repair mortar, high flow cement grout, epoxy repair mastic, steel bar anti-rust agent, fast leaks stopping agent, repair object crack mortar, tile adhesive, mosaic adhesive, glassed tile adhesive, tile grout., concrete admixture
Supplying business of construction chemicals like Anchor grout, Epoxy floor coating
