Supplier: Dth Hammer, Bits, Tricone Bit, Drill Pipe, Mining Bits
Drill Bits
Material: high carbon spring steel, spring steel, stainless steel, alloy steel Compression Spring, Extension Spring : Wire Diameter: 0.2-40.0mm Torsion spring wire diameter :0.2-35mm Surface Finish: black , Zinc, Nickel, silver, golden, tin, powder coating, shot pin Applications: Automotive, medical device, agricultural machinery ,electronics, toy, electric power distribution. Extension spring hook include Germany hook, British hook, Side hook We can customize special design of springs based on your requirement.
Power Screw Bits
1.Brief introduction Size 311.1mm Iadc 537 Bearing type Sealed bearing Thread connection 6 5/8"reg pin Wob(kn/mm) 0.35~1.05 Rpm(r/min) 80~40 Make up toqure(kn.M) 16.300~21.700 Weight(kgs/pc) 105 Color Customized Packing Plywood box(free-fumigation) Industrial standard Sy/t5164 Moq 1 pc Payment terms T/t, western union, and l/c are acceptable Applications Medium soft with low compressive strength and harder abrasive stringers, such as hard shale, hard gypoltye, soft limestone, sandstone, and dolomite with strngers, etc. Note:other size and iadc is avaiable Weight 45kg
We are one professional manufacturer of rock drilling tools and consumables in china. Our main products include dth hammer, dth bit, button bit, drill rod, shank adaptor, coupling sleeve, overburden drilling equipment, which are used for mining, quarrying, tunneling, water well drilling, mineral exploration, civil engineering and construction. Please feel free to contact me if you are interested in our products. Many thanks.
A rotation drill rig, air compressor and the "DTH drill string" are the essential unit for DTH drilling while the "DTH drill string" is always made up of DTH drill rods, DTH hammer and DTH bits. As one of key component, the DTH hammer acts as a role of converting the air pressure to the impact energy, simultaneously transferring impact energy and rotation force to DTH bits. The optimum range of hole size for blast hole drilling with DTH is 90 mm to 254 mm (3 -10). Smaller blast holes are generally drilled using tophammer, and larger holes generally use rotary machines. In other applications, like foundation drilling, DTH hammers can be used with single bit in hole sizes up to . 750 mm (30). With multiple hammer units CD (Cluster drills) drill holes up to 70 or 1778 mm. As a rule of thumb, the smallest hole diameter a DTH hammer can drill is its nominal size. A 4 inch hammer will drill a 4 inch (102 mm) hole. The limiting factor is the outside diameter of the hammer, because, as hole diameter reduces, airflow is restricted. Maximum hole size for production drilling is the nominal hammer size plus 1 inch, so for a 4 inch hammer the maximum hole size is 5 inch (127-130 mm). Choosing the right hammer is largely determined by hole size and type of rock formation. Ideally, the size of the hammer should match the required hole dimension as closely as possible, leaving just enough space for cuttings to evacuate the hole.
1.Tighten the bits when screw on. 2.When the bit lower down to the bottom , Should give a soft pressure, slow drilling .After a drilling 0.2m-0.3m with appropriate pump, then give the conventional drilling. 3.Drilling could not be without water, if not fear the normal vibration sound or drill too slow, lift the drill to check without delay. 4.When drill jammed, withdraw first, should not to force the rig start. 5.Drill could not without water, to ensure that the bit will be too hot. 6.Use the bits in right order , big size first, then small one . 30*35*40cm 45kg
The used tricone bits are much more cheaper than the new ones because of the cost is low, but the quality is promised. 30*35*40cm 45kg
