Film Shrinkage Test Equipment Film Shrinkage Tester GBK-D1 Film Shrinkage test, known as linear thermal shrink test or free shrink test, is used for analyzing the effect of temperature on heat shrinkable films made from polyethylene, ethylene copolymers and their mixtures. Basically, shrinking force, contracting force and shrinking ratio can be measured in such determination. GBPI Film Shrinkage tester conforms to the multiple national and international standards: ASTM D2732 - Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting ISO 14616 - Plastics Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures Determination of shrinkage stress and contraction stress DIN 53369 - Testing of plastic films determination of the shrinking stress Film Shrinkage Test Equipment GBK-D1 is used to determination of the degree of unrestrained linear thermal shrinkage and dimensional stability at different temperatures. Widely used in industries of plastic material, plastic products, petroleum, chemicals, research institute, inspection agency and so on. Principle This tester uses the principle of air heating to connect the tested sample to the tension sensor and displacement sensor. After reaching the maximum shrinkage force, it is placed in an external test environment with an ambient temperature of 23 to cool down. The reference temperature, shrinkage force and displacement are recorded, and the recorded data can be used to determine the optimal shrinkage conditions of the film. Standards ISO 14616, ASTM D2732, DIN 53369
Features: * LCD display of 128 64 matrix is used. * Hardness scales(HV ,HB,HRC,HRB,HRA,HS). * RS232 interface and USB to PC * Max 600 groups impact times:32¡«1 of data can be stored at internal. * Back light display has been used to make convenient or the user in poor light. * Upper and lower limit can be preset. It will alarm automatically when the result value exceeding the limit. * Material of cast steel¡± is added HB values can be read out directly when D/DC impact device is used to measure cast steel¡± workpiece. * Power is two of AA battery. Continuous working period: approx. 100 h (no back light on). * Software of PC can be installed according to the requirements of user. The function will be more powerful to satisfy the more demands of quality control and management.
Roughness tester.
Ft-f1 fogging tester Characteristics: Determines auto's fogging characteristics precisely, guarantees automobiles driving safely. Be applicable for the laboratory and works in low noise. Data test and analysis with professional software, convenient and prompt. Bath temperature controlled by thermostat can be kept constant to 0.1ªc, creating precise testing conditions. Designs friendly and integrally, operates safely and conveniently. World-famous brand elements with stable and reliable performance. The strictly controlled constant thermostat can be used for the other experiments. Conforms to din 75201, iso 6452, sae j1756.
2. Test shields in 1394 and USB cables3. Ergonomic portable handheld design4. Tests installed wires and patch cables5. Remote unit stores in Main unit6. 600 ft test distance (RJ-45/RJ-11/BNC)7. Simple one button test8. Convenient battery access9. Built in battery access10. LEDs indicate connections and faults -
1.1Product Introduction Apva-401 is a special instrument for testing characteristic of ct; the tester can finish ct transformation ratio test, ct polarity test, volt-ampere feature curve drawing and ct error drawing. It has large output, high precision, stable performance and automatic testing. 1.2 Funtion 1 ct transformation ratio test 2 ct polarity test 3 ct volt-ampere feature curve measurement 4 ct ratio error measurement 5 error curve measurement 6 result print 7 unload data to pc 8 pc online test .
Lx-c durometer meter applied to foam, sponge, shoe materials, such as durometer testing of materials with low hardness. This product is light hg/t2498-93 and other relevant standards. 1. Dial value: 0 ~100hc 2. Needle stroke: 2.5 mm 3. Measure range: 10 ~90hc 4. Needlepoint size: sr 2.5 mm 5. Dimension:115¡¡§¡é60¡¡§¡é25mm 6. Weight: 0.5 kg
A great scientific innovation must lead to a great technological breakthrough. Tck•w portable rope testers weigh only 1.8 kg, about 1/6~1/25 of the weight of conventional ndt testers. The sensitivity of tck•w sensors could reach 5v/mt, and about 700times higher than conventional sensors. The gap between sensor and wire rope is about 20-30mm which achieves non-contact inspection, it does not affected by grease, normal warped wire, and rope-running speed which shown that passing-through capacity is good. When an inspection is completed, tck•w rope testers are capable to display testing data, flaw graph, data table, and test report on lcd screen. After connected to a computer and printer, a formal test report could be printed, which provides scientific reference for users to use wire ropes more safely and replace wire rope more properly. Key features 1. High inspection precision, strong resolution and stable performance: “weak magnetism sensor” technology invented uniquely by our company, its sensitivity is 700 times higher than traditional tester. The sensor has strong resolution, and can inspect quantitatively actual wire rope flaws under various working status. 2. Small volume and light weight: the weight of w portable flaw detector is less than 2kg, which is only 1/6—1/20 of similar products at home and abroad. 3. Easy operation: inspection system realizes intelligent “fool” operation; on-line lock or unlock only needs 1 second; it only needs one person to operate, and the operation is much easier than using a mobile phone.
Hardness tester hln-11a Wide measuring range, for all metallic materials Direct display of hardness scales hrb, hrc, hv, hb, hs, hl Conversion to tensile strength (u.T.S.) Test at any angle, even upside down Removable printer included Six impact devices are available for special applications Large lcd display showing all functions and parameters Battery low indication New function of software calibration Power charging indication on the keyboard led Fault distinguish in details Weight:6kgs Dim:51*38*17
1.1 General introduction APGK-307 is special instrument for power system GIS mechanical properties measuring. The instrument takes IPC for the core to sample and data process. It has 12.1 LCD to display and 12.1 touch pad for operation. Rich experience database makes the tester more intelligence. The tester has the characteristic of accurate test data, strong anti-jamming, easy operation, small size and light weight. 1.2 Functions 1. Measure opening and closing time, synchronism performance ,bounce time and bounce times of common and graphite GIS. 2. Measure distance, average speed and instantaneous speed of on and off of common and graphite GIS. 3 Finish test of continuous on and off of common and graphite GIS. 4. Measure coil current of common and graphite GIS. 5. Draw GIS state-time curve, current-time curve, distance-time curve and speed-distance curve. 6. Show 12 GIS port status of common and graphite GIS. 1.3 Technique index 1) Time measuring: Number of ports of GIS measured :í_12 Range of the setting time during the measuring course: >100 seconds Resolution: 0.01ms 2) Distance measuring: Distance sample rules:0-3 Range:
