Wansheng Environmental Protection Engineering Co., Ltd.

BCPL manufactures two & three-piece welded steel cylinders for LPG used in automobiles, meeting the established standards and as per the customersâ?? requirement. These auto LPG containers are available in cylindrical and toroidal shapes. The cylindrical containers range from 200 to 400 mm in diameter, whereas toroidal containers range from 180 to 270 mm in diameter. The cylinders are available in the following capacities: 4.9 Ltr, 5 Ltr, 5.2 Ltr, 5.8 Ltr, 15 Ltr, 25 Ltr, 28 Ltr (toroidal), 34 Ltr (toroidal), 36 Ltr, 50 Ltr, 60 Ltr and 75 Ltr. BCPL is one of the renowned companies in India known for the quality of automotive tanks. These tanks are marketed through a Pan-India network of distributors and dealers.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

444 stainless steel is a low-carbon, dual-stabilized ferritic stainless steel that is highly resistant to corrosion, especially in chloride environments. It is often used in applications where high corrosion resistance and good formability are required. Some of the key properties of 444 stainless steel include: Corrosion resistance: 444 stainless steel has excellent resistance to corrosion, especially in chloride environments such as seawater, brackish water, and chloride-containing acids and solvents. Heat resistance: It can withstand high temperatures up to 950�°C (1742�°F) without losing its strength or corrosion resistance properties. Formability: It has good formability and can be easily fabricated into various shapes and sizes. Weldability: It can be welded using common welding techniques, and does not require preheating or post-weld heat treatment. Cost-effective: Compared to other stainless steels, 444 stainless steel is a cost-effective option due to its lower nickel content. Some of the common applications for 444 stainless steel include: Automotive exhaust systems: It is often used in the manufacture of automotive exhaust systems due to its excellent corrosion resistance and heat resistance. Industrial equipment: It is also used in various industrial equipment such as heat exchangers, tanks, and piping systems. Kitchen appliances: It is used in the manufacture of kitchen appliances such as refrigerators, dishwashers, and ovens due to its good formability and corrosion resistance. Overall, 444 stainless steel is a highly versatile and cost-effective material that is ideal for use in corrosive environments where high corrosion resistance and good formability are required. Here are some of the most common international standards for 444 stainless steel: ASTM A240/A240M: Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications ASTM A268/A268M: Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service ASTM A554: Standard Specification for Welded Stainless Steel Mechanical Tubing EN 10088-2: Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes JIS G4305: Cold-rolled stainless steel plate, sheet and strip GB/T 3280: Cold rolled stainless steel plate, sheet and strip We can provide the following of the form:444 stainless steel coil; 444 stainless stee strip;444 stainless stee plate; 444 stainless steel sheets; 444 stainless steel tubes; 444 stainless steel pipe;444 stainless steel flat; 444 stainless steel bar 444 stainless steel is generally used to manufacture stress corrosion resistant equipment, video machinery, automotive engine exhaust pipe storage tanks, solar water heaters, printing and dyeing machinery, heat exchangers, etc.