Cable cleats can be used for XLPE LV, MV and EHV cables. Typical installation applications include: vertical shaft, termination support, riser pole, tunnel, seismic, manhole/duct entrance, cable tray, and wind towers. Custom clamping solutions are also available for non-standard / special applications. Cast Aluminium clamps are available in different cable diameter ranges. Each clamp is supplied with stainless steel mounting bolts and neoprene liners. Optional stainless steel springs are available to allow for expansion and contraction of the cable, while maintaining adequate holding force to secure the cable. Other specialty types of clamps can be custom designed to suit the customers specific cable dimensions and/or special installation requirements. Examples include single point mounted clamps and multi-cable clamps. Single point mounted clamps allow clamping in positions where two perpendicular holes to the cable direction are difficult to maintain or are not possible (for example, snaking of the cable). Multi-cable clamps allow more than one cable to be clamped together in the same orientation utilizing only one clamp. We are the manufacturer of fiberglass reinforced cable clamps which are available in a variety of different styles for various cable applications. These clamps are ultraviolet ray protected, flame resistant and free from halogens. Mounting hardware, neoprene liners and springs are all optional items.
Introduction : Power has wide range of tested stainless steel made link boxes and sheath voltage limiter covering full range of HV cable sheath earthing application for 66 KV to 400 KV Underground Power Cables. Link Boxes provide sealed and dry environment to HV Cable Sheath Earthing. Also Stainless steel boxes are designed such as it is easy to install and reliable against sudden fault occurrence. Types Of Link Box : Power has following types of Link Boxes: Single Phase Link Box Three Phase Straight Bonding Link Box (3-1 Way) Three Phase Cross Bonding Link Box (3-1 Way) Three Phase Cross Bonding Link Box (6-1 Way) Features : Mechanical Feature: Enclosures are rated IP65 for Outdoor/Indoor application and IP68 for Underground application. Enclosures are made from high quality Stainless Steel(SS304) with powder coated. Conductor is made from High Conductive Copper with Tinned Plated. Epoxy Resin insulator is used to separate live parts from enclosure. is used as per the specification of Bonding cable. Link Boxes are sealed with Rubber gasket and Check Nuts. Electrical Feature: High conductive electrolyte copper is designed such as it will sustain up to 40KA short circuit current for 1 sec. Link Boxes have Epoxy Insulators which maintain the insulation between Live parts and Earth. Double Earthing will provided with special client requirement. Insulation between Phase to Phase and Phase to Earth will be Type Tests: 25 KV DC Voltage withstand Test for 1 min. Degree of protection IP65 and IP68.
Floating cable which can be applied to underwater robot equipment, either in fresh water environment or in seawater environment. It is widely used in marine exploration robot, underwater ROV UAV remote control submersible, underwater camera, underwater construction, underwater search and rescue robot, pipeline detection robot, submersible pump and the link between various underwater electrical equipment and shore based equipment; Link of signal transmission, power supply and equipment control system from underwater to water.
Silicone cable, multi conductor (36AWG silver plated copper), PFA insulating.
Application Use for control and connecting cable on data transmission within building management system, speaker audio system and control measurement. Suitable for use in dry and damp environment. Cable Structure & Features Conductor Material : Tinned copper stranded Insulation : Semi-Rigid PVC Drain Wire : Tinned copper stranded Shielding : Aluminium foil laminated screen Outer Sheath ; PVC Sheath Colour : black or gray Technical Data Standard : UL Style 2464 Approvals : UL apporoved Rated Voltage : 300V Testing Voltage : 1500V Flame Retardant : VW-1 Insulation Resistance : Min 20Mx km Min. Bending Radius : 10 x cable diameter Operating Temp. : -30C / +80C
Flat Cable M&P is able to support a full line of flat cable and flat ribbon cable for electronic applications. Providing both power and data transmissions, flat cables are mainly used for internal connections within the equipment. They are available in a wide range of configurations to accommodate different connection and data transmission requirements and the range of sizes of the equipment using the cables. Flat cables provide consistent performance due to their layout and the spacing between the cables and are lighter, thinner and more flexible than other cables. Features of Our Flat Cables & Wire * Flat, ribbon and twisted configurations, with different levels of flexibility. * Shielded or jacketed cable to reduce signal interference. * Range of pitches and pin configurations to accommodate the application requirements. * Easy to fasten with clamps, adhesive, and tape. We provide custom services, including marking, kitting and custom cable design to provide you with a custom solution for your cabling application. Contact us to find out more about Flat Cables and Wires.
Liquid Cooled Charging Cables are electric vehicle charging cables that utilize liquid cooling to achieve high-speed charging. These cables feature a 500A current rating and a 1000V voltage rating for charging speeds up to 500KW.
DC40KV, 25 or 39 ohm coaxial cable, for nuclear power application. XLPE insulation with non-halogen jacket.
UL2651 flat ribbon cable, from 10P to 64P
