Cycloidal gear reducers, cyclo drive reducer
Xingguang brand jxj series cycloidal pinwheel/lantern reducer adopt the principle of planetary gearing transmission and the construction of cycloidal gear mesking with pin wheel, conform to standard jb/t2982-94, with features of big ration, high efficiency, compact structure, small volume, long life. Little breakdown, strong abillity against impact and so on. It is widely applied to ceramic, drind, food, light industry, textile, mineral and metallurgical, lifting and transportation, printing and dyeing etc. Industry. Input power 0.25-18.5kw Ratio 9-7569 Output torque up to 5000n.M. Wood/carton.
Supplier: Inline helical gear motor, parallel helical gear motor, helical worm gear motor, helical bever gear motor, cycloidal gear reducer
Services: Export
Supplier: Gearbox, cyclo drive, gear motor, gearhead, servo gear head reducer, speed variator, cycloidal drive, planetary gear reducer, power transmission products
WF series reducer represents a wide range precision reduction gears with flange shaped case. WF series high-precision reduction gears consist of an accurate reduction mechanism and high-capacity radial and axial cylindrical bearings. This design of gears allows the mounting of the load directly to the output flange or case without requigears are characterized by a modular design, lt can be directly connected to any servo brand motor.
Power: 0.25~90 kw Output torque: top~22920 n.M Output speed: 0.011~161 r/min Characteristics: 1. High speed ratio and efficiency Single stage transmission can reach to 1:87 of speed-down ratio and the efficiency is more than 90%. If use multi-speed drive the speed-down ratio is bigger. 2. Compact structure and small size Being adapted epicyclic transmission principle, the input & output shaft are at same axis center, it is compact. 3. Smooth and stable run and low noise The cycloidal pinwheel has more meshed teeth, the overlapping coefficient id big and the machine part is stable, the vibration and noise is limited at the minimum content. 4. Reliable in operation and long life Because the main parts are made of bearing steel through quenching treatmenthrc58-62, it got high strength. Meanwhile the transmission contact of part adapts rolling friction, so it is durable and long life. 5. Strong overload capacity, resistant to impact, small moment of inertia. It is used for the occasion of frequently starting and positive and negative rotary.
Gear Reducer: Double helical involute, double reduction. Its unique features result in a gear reducer that can withstand heavy cyclic loads and provide years of service with minimal maintenance. Meets or exceeds API 11 The torque rating of the gears shall be as determined by API Specification 11E and AGMA Specification 422.03. -All pinions and shafts shall be made of 4145 high alloy steel. Material certifications are required. Gear Reducer Housing:Gear Reducer is a two piece housing is ASTM A48 gray iron casting Gear Reducer Lubrication:An exclusive feature of every VENDOR unit is its gearbox Positive oil lubrication system. This unique system should uses oil buckets to fill troughs that continuously feed the right amount of oil to each gearbox bearing, regardless of the direction of rotation, at pumping speeds as low as 1 strokes per minute without modification (wipers not required). The reducers oil capacity should be large enough to operate with no sump. Meets API 11E NB:Gear reducers shall be shipped full of oil and ready to be placed into operation High/Intermediate/Low Speed Bearings:The gear reducer should contains properly sized anti-friction bearings, rather than energy-consuming bronze bushings. Each bearing is set in a carrier for ease of removal and installation. Should meets or exceeds API 11E Gear Reducer Seals:High and Low speed shaft should use Butadiene acrylonitrile rubber seals. Meets AP111E Section 7.4.9
Gear Reducer: Double helical involute, double reduction. Its unique features result in a gear reducer that can withstand heavy cyclic loads and provide years of service with minimal maintenance. Meets or exceeds API 11 The torque rating of the gears shall be as determined by API Specification 11E and AGMA Specification 422.03. -All pinions and shafts shall be made of 4145 high alloy steel. Material certifications are required. Gear Reducer Housing:Gear Reducer is a two piece housing is ASTM A48 gray iron casting Gear Reducer Lubrication:An exclusive feature of every VENDOR unit is its gearbox Positive oil lubrication system. This unique system should uses oil buckets to fill troughs that continuously feed the right amount of oil to each gearbox bearing, regardless of the direction of rotation, at pumping speeds as low as 1 strokes per minute without modification (wipers not required). The reducers oil capacity should be large enough to operate with no sump. Meets API 11E NB:Gear reducers shall be shipped full of oil and ready to be placed into operation High/Intermediate/Low Speed Bearings:The gear reducer should contains properly sized anti-friction bearings, rather than energy-consuming bronze bushings. Each bearing is set in a carrier for ease of removal and installation. Should meets or exceeds API 11E Gear Reducer Seals:High and Low speed shaft should use Butadiene acrylonitrile rubber seals. Meets AP111E Section 7.4.9
Gear Reducer: Double helical involute, double reduction. Its unique features result in a gear reducer that can withstand heavy cyclic loads and provide years of service with minimal maintenance. Meets or exceeds API 11 The torque rating of the gears shall be as determined by API Specification 11E and AGMA Specification 422.03. -All pinions and shafts shall be made of 4145 high alloy steel. Material certifications are required. Gear Reducer Housing:Gear Reducer is a two piece housing is ASTM A48 gray iron casting Gear Reducer Lubrication:An exclusive feature of every VENDOR unit is its gearbox Positive oil lubrication system. This unique system should uses oil buckets to fill troughs that continuously feed the right amount of oil to each gearbox bearing, regardless of the direction of rotation, at pumping speeds as low as 1 strokes per minute without modification (wipers not required). The reducers oil capacity should be large enough to operate with no sump. Meets API 11E NB:Gear reducers shall be shipped full of oil and ready to be placed into operation High/Intermediate/Low Speed Bearings:The gear reducer should contains properly sized anti-friction bearings, rather than energy-consuming bronze bushings. Each bearing is set in a carrier for ease of removal and installation. Should meets or exceeds API 11E Gear Reducer Seals:High and Low speed shaft should use Butadiene acrylonitrile rubber seals. Meets AP111E Section 7.4.9
