MATERIAL: PC natural 100% pure pc without any coating
CATEGORY: PC
TYPE: Natural
SPECIFICATION: Separate 25 kg bag and Mark per month 78 mt 100% pure pc without any coating ,post Industrial materials
Origin: Bangladesh
LOADING WEIGHT: 24 Ton
FOB (USD/Ton): 1450$ - 1700$
Packaging: Jumbo Bag
Est. Shipping Time: 15, 30, 45 days
Our Commitment
We are committed to delivering in accordance with the quality given, source and licensed in the field of scrap transportation.
2Lians always for the purpose of satisfying customers on the criteria of sustainability and fairness through high work efficiency
BARILAC barrier coatings are the most suited sustainable solution to replace polycoated laminated board,
waxcoated, PVDC coated etc all non sustainable alternatives. Barilac barrier coat is recommended for
paper cup, trays, foodtrays, pizza boxes, ice cream cartons etc.
The special product features are.
- Low COBB
- Good oil and grease resistance
- Good Moisture Vapour Transmission rate
- Good heat sealing performance
- Good water resistance
- Low odour
- FDA compliance
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Two component, acrylic aliphatic polyurethane coating. Offers excellent gloss and colour retention. It is used for subtracts as steel, aluminum, glass-fiber, plywood etc.
We offer a wide plethora of Zinc in many forms including LME registered
and non registered Special High Grade Ingots and Jumbos, cathodes,
dust, foil, granules, powder, pieces, anodize activated powder, shot,
and a mossy form.
Zinc is a bluish-white, lustrous metal. It is brittle at ambient temperatures but is
malleable at 100 to 150°C. It is a reasonable conductor of electricity, and burns in air
at high red heat with evolution of white clouds of the oxide. Plating thin layers of zinc
on to iron or steel is known as galvanizing and helps to protect the iron from corrosion.
