Supplier: Reverse osmosis system, deionization systerm, water softener system, media filtration system, infiltration system, membrane bioreactor system provider, ion exchange resin, membrabe filter, filtration media, cartridge and bag filter, flow meter, conductivity meter, pressure gauge, control valve, RO chemical, test kit, FRP tank, storage tank
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.
[Alkaline Water Ionizer] ALKAMEDI offers a variety of product groups and series designed to cater to consumers\' needs and make their home circumstances and purposes more convenient and accessible. AML 3000(S) is a sleek and compact luxury model ionizer that embodies the contemporary trend of simplicity in its stylish design. Equipped with an electrolysis chamber containing 5 platinum-coated titanium electrode plates, ALKAMEDI offers a range of alkaline water options at 3 different levels, along with 3 levels of acidic water and purified water. This diverse selection caters to individuals\' varying health needs.
ALKAMEDI ionizers are using a single filtration system with 3 different filter types at the moment offers the most reliable and powerful water filter with state-of-art technology of ALKAMEDI. â? � � � � FB2 : 6 steps of Carbon Block Compound Filter â?¡� � � � FU3 : 8 steps of Advanced Ultra Hollow Membrane Purification Filter â?¢� � � � FNC : 7 steps of NANO Silver Carbon Block Compound Filter The effectiveness of the filtration is determined by the valid filtration capacity verified by a testing institution, and this product is composed of a nano-carbon block composite with a valid water capacity of 3,600 liters for approximately 6 months. It is recommended to use for approximately 6 months and a voice guide will inform you when it is time to replace the filter. Alkamedi does have all kinds of certificates related to each continents and countries we export to such as  CE, CB, UL, NRTL, TUV� etcâ?¦in order to meet all electrical regulations in each countries and regions.
ALKAMEDI ionizers are using a single filtration system with 3 different filter types at the moment offers the most reliable and powerful water filter with state-of-art technology of ALKAMEDI. â? � � � � FB3 : 6 steps of Carbon Block Compound Filter. â?¡� � � � FU4 : 8 steps of Advanced Ultra Hollow Membrane Purification Filter. (Carbon Block Compound + UF Module Filter)� � � Expected in Q1, 2024 â?¢� � � � FN2 : 6 steps of NANO Silver Carbon Block Compound Filter. (Carbon Block Compound + NANO Filter)� � � Expected in Q1, 2024 The effectiveness of the filtration is determined by the valid filtration capacity verified by a testing institution, and this product is composed of a nano-carbon block composite with a valid water capacity of 3,600 liters for approximately 6 months. It is recommended to use for approximately 6 months and a voice guide will inform you when it is time to replace the filter. Alkamedi does have all kinds of certificates related to each continents and countries we export to such as CE, CB, UL, NRTL, TUV etc in order to meet all electrical regulations in each countries and regions.
Supplier: 1121 parboiled rice, 1121 white and sella rice, or ir64 white and parboiled rice, all types of basmati and non basmati rice, corn (maize), corn flour, brown cumin, black cumin, cardamom, dry red chili, chili powder, raw sulphur, hulled white sesame seed,, poppy seed, all types and sizes floor ceramic tiles in all size, all type wall tiles in all size, all types of front elevation tiles, all type of marble & granite, all type of poly pvc door window frame, all type waterproof door, all type bathroom door, all types of sanitary ware like a washbasin, toilet seat urinal seet and other all sanitary ware. door frame (poly pvc), d6 diesel, dap fertilizer, urea fertilizer, bitumen, en590 10ppm diesel, jet a1 fuel, chicken paw, chicken feet , other chicken part, whole chicken, any grade steem coal and charcoal, d2 gas oil, liquefied natural gas, liquefied petroleum, mazut m100, aviation kerosene colonial grade 54 and all type date , dates
Buyer: Dry fruits, spices, areca nuts, palm oil, areca, betelnut, clove, cardamom, black cardamom, bay leaves, cinnamon, almond, pistachio, cashew nuts, date, dry dates, refined soya oil, refined premium sunflower oil