Specifications:
MS Plate ( 6100X1500X6 mm )-6 mm MS Plate ( 6100X1500X8 mm )-8 mm MS Plate ( 6100X1500X12mm )-12mm MS Plate ( 6100X1500X10 mm )-10 mm MS Angle ( 1.5"X1.5"X5 mm ) MS Angle ( 2"X2"X5 mm ) MS C Channel ( 4"X2"X6 mm ) MS Hot Roll ( 6000X200X150X5X6 mm ) MS Rod ( 500 DWR )-100 MS Plate-24 mm MS Rod ( 500 DWR )-10 mm MS Angle-50X50X5X6000 mm MS Plate-20 mm MS Plate-30 mm MS Plate-25 mm MS Rod ( 500 DWR )-12 mm MS Plate-35 mm MS Checker Plate-4 mm MS HoleSheet ( Alternate-4'X8'X4 mm ) ( 4'X8'X3mm, Hole Dia-6 mm MS HoleSheet ( Alternate-4'X8'X3 mm ) ( 4'X8'X4mm, Hole Dia-10 mm MS Hole Sheet ( 4'X8'X3 mm ) Hole Dia:8 mm MS Hole Sheet ( 4'X8'X3 mm ) Hole Dia:12 mm MS Shaft -16 mm MS Shaft -50 mm
Quantity : 1 container
Buyer is interested to receive quotations for the following RFQ -
Product : Steel Plates
Specifications:
Grade A with BV certificates 18*2000*9000 mm qty 120 MT 20*2000*9000 mm
Qty : 490 MT 22*2000*9000 mm qty 50 MT 25*2000*9000 mm qty 15 MT 30*2000*9000 mm qty 85 MT 30*2500*9000 mm qty 92 MT 40*2000*9000 mm qty 23 MT 50*2000*9000 mm qty 29 MT 35*2000*9000 mm qty 45 MT 50*2000*6000 mm qty 101 MT 100*2000*4000 mm qty 71 MT Total qty ~1121 Ton
Please provide a quotation to the following requirement from importer -
Product : Steel Plate Carbon, Hot Rolled, Alloy
Specifications:
STRUCTURE ANNEALED (LENGTH= 1000MM+ 10/-0) X
WIDTH (180 MM + 5/-0) XTHICK (6MM ± 0.30MM)
NO.35 Cr. Mn SiA
CHEMICAL COMPOSITION
C=0.32-0.39% Si=1.10-1.40%
Mn=0.80-1.10% Cr-1.10-1.40%
P=Max 0.025% S=Max 0.025%
Cu= Max 0.25% Ni = 0.30%
MECHANICAL PROPERTIES
Tensile strength=600-800(MPa)
Elongation = 16% Min
Quantity: 30,400 Kg.
ITEM # 2:
STEEL PLATE CARBON, HOT ROLLED, ALLOY
STRUCTURE ANNEALED (LENGTH= 1000MM+ 10/-0) X
WIDTH (180 MM + 5/-0) XTHICK (6MM ± 0.30MM)
NO.35 Cr. Mn SiA
CHEMICAL COMPOSITION
C=0.32-0.39% Si=1.10-1.40%
Mn=0.80-1.10% Cr-1.10-1.40%
P=Max 0.025% S=Max 0.025%
Cu= Max 0.25% Ni = 0.30%
MECHANICAL PROPERTIES
Tensile strength=600-800(MPa)
Elongation = 16% Min
Quantity: 35,700 Kg.
SPECIAL CONDITIONS: To be followed by Shipper/Maker;
1. Same (Single) competitive Unit Rate must be quoted against the same tendered items.
2. Full Qty falling in both inspection authorities must be quoted otherwise offer will be ignored.
3. Sample to be provided by the firms within 15 x days of technical opening except last Supplier,
4. Validity of offer at least 90 days (Extendable if required) would be considered w.e.f
commercial opening of tender (s) after acceptance of technical offers
5. Conditional offers are likely to be ignored.
6. Needful supporting technical literature/ Catalogue/ Brochure against each tender it
must accompany technical quotation if requisite/relevant technical literature found
missing, quotation will be considered rejected.
7. Performance Bond (in shape of CDR/B.G) should be provided against L.O.I for issuance of formal contract. However,
20 The supplier will render a Warranty / Guarantee Certificate for a period of 12 x months
from final acceptance of store
21 Protocol of inspection will be followed as per inspection authorities.
Further requirements:
· Supplier type: manufacturer
