Ameland Energy

Aviation Jet Fuel is a type of aviation fuel designed for use in aircraft powered by gas-turbine engines. It is colourless to straw coloured in appearance. The most commonly used fuels for commercial aviation are Jet A and Jet A1, which are produced to a standardised international specification. The only other jet fuel commonly used in civilian turbine-engine powered aviation is Jet B, which is used for its enhanced cold-weather performance. Jet fuel is a mixture of a variety of hydrocarbons. Because the exact composition of jet fuel varies widely based on petroleum source, it is impossible to define jet fuel as a ratio of specific hydrocarbons. Jet fuel is therefore defined as a performance specification rather than a chemical compound. Aviation Jet Fuel is commonly referred to as JP54. However, this is the wrong terminology as there is no such grade of Jet Fuel. Jet A and Jet A1 are what refineries offer. Aviation Jet fuel Gas is what powers turbine aircraft engines. Worldwide, Jet Fuel is the most used low Sulphur content Kerosene. For instance, Colonial JP54 is similar to Jet A except the energy is 18.4 mj/Kg compared to the 42.8 MJ/kg of Jet A. Most importantly there is also a slight difference in additives. Aviation Jet Fuel B is used for its extremely cold weather performance. However, aviation Jet fuel Bs lighter composition makes it more dangerous to handle. For this reason, it is rarely used except in very cold climates. A blend of approximately 30% Kerosene and 70% Gasoline. Because of its very low freezing point (60 C (76 F), it is known as a wide cut fuel and has a low flash point as well. Aviation Jet Fuel B is primarily used in some military aircraft. In Canada, it is also used because of its freezing point. Aviation Kerosene standards are published as GOST10227-86. The standard consists of different properties. It separates paraffin and gasoline in the refinery. Military organisations around the world use a different classification system of JP (for Jet Propellant) numbers. Some are almost identical to their civilian counterparts and differ only by the amounts of a few additives. For instance, Jet A1 is similar to JP 8, Jet B is similar to JP 4. Military fuels are highly specialised products and are developed for very specific applications. Jet fuels are sometimes classified as kerosene or naphtha type. Kerosene type fuels include Jet A, Jet A1, JP 5 and JP 8. Naphthatype jet fuels, sometimes referred to as wide cut Jet Fuel, including Jet B and JP 4.

product Description : These Products are Exported with Stringent Adherence to Standard Russian Export Specifications with Respective GOST. Price of product ( USD price or FOB price) : Product will be priced in USD$ Based on an Appropriate PLATTS INDEX or a FIXED Price and the Agreed Upon Shipping Method. The Price will be Mutually Agreed to by Buyer and Seller Product origin : Russian Federation Key Specifications/Delivery/Logistics : 1. Certification SGC or Equivalent 2. Payment Terms = Letter of Credit ( Details to be agreed upon by Buyer and Seller 3. Delivery Time = Varies by Destination 4. Port of Loading = TBD Minimum Order Size & Contract Term : Minimum Monthly Quantity = 100,000 MT X 12 Month Contract Required with R & E up to 120 Months

D6 is also be known as Residual Fuel Oil and is of high-viscosity. This particular fuel oil requires preheating to 220 - 260 Degrees Fahrenheit. D6 is mostly used for generators. D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400 Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil. The price of D6 diesel traditionally rises during colder months as demand for heating oil rises, which is refined in much the same way.In many parts of the United States and throughout the United Kingdom and Australia, d6 diesel may be priced higher than petrol. D6 Diesel Standards and ClassificationCCAI and CII are two indexes which describe the ignition quality of residual fuel oil, and CCAI is especially often calculated for marine fuels.

We can connect you with our friend end sellers/title holders to offer express work with petroleum products of Russian or non-Russian origin, where they can provide reliable and serious offers. Please contact us only if you are the real end buyer or his direct mandate. The products list: - Diesel EN590 - JET FUEL A1, JP 54 - VIRGIN D6 FUEL OIL - LPG, LNG - AGO Automotive Gas Oil - Gasoline Octane 72, 76, 91, 93, 95

EN590 Diesel Fuel EN590 DIESEL FUEL PRODUCT ORIGIN: KAZAKHSTAN DELIVERY: CIF, FOB, TTO INSPECTION: SGS PAYMENT METHOD: TT, MT103, TRC20USDT Quantity. 100, 000MT per month for 13 months. Shipping Terms. CIF is possible, yes. Destination Port. Jurong Singapore possible

SPECIFICATION of ULSD 10 ppm Diesel Fuel (EN590) Density at 15 0C Kg.m3 820-845 Polycyclic aromatic hydrocarbons EN 12916 wt% B Max Flash Point EN 2719 0C >55 Cold Filter Plugging Point CFPP EN 116 0C Winter Grade -15 Max Summer Grade 5 Max Distillation EN ISO 3405 Recovered at 250C Vol% 65 Max Recovered at 350C Vol%95% (Vol/Vol) Recovered at 0C 360 Max 85 Min Sulphur EN ISO 20846 EN ISO 20884 Mg/kg 10 Max Carbon Residue (on 10%residue) EN ISO 10370 wt% 0.30 Max Viscosity at 40C EN ISO 3104 Cst 2.0-4.5 Copper Strip Corrosion (3h a5 50C) EN ISO 2160 Fatty acid methyl ester(FAME) content EN 14078 Vol% 7.0 Max Cetane Number EN ISO 5161 EN 15195 51 Min Cetane Index EN ISO 4264 Calculated 46 Min Water EN ISO 12937 Mg/kg 200 Max Particulate Matter EN 12662 Mg/kg 24 Max Oxidation Stability EN ISO 12205 EN 15751 G/m3 H 25 20 Max Min Lubricity (wsd1,4) at 60C EN ISO 12156/1 Um 450 Max Quantity: Minimum 25.000 MT - Maximum 100.000 MT Origin: Kazakstan Loading Port: Gorgia Batumi Payments (SBLC or BG) via MT-760 unconditional, cashed back from top 25-30 world banks with sellers acceptable verbiage.