It is the most typical cold paint road marking machine, oftentimes called cold paint striper or cold striping machine as well, is widely used for spraying cold-solvent paint, water-based paint and other single-component paint, can be applicable to various construction environments as well. It has the characteristics of stable performance, flexible operation and convenient construction and so on. Engine 5.5HP Honda gasoline engine Marking method High pressure airless spraying Paint pump flow 9L/min Rated maximum working pressure 20Mpa Paint pump and control mode Piston reciprocating, single pump Applicable paint Cold-solvent, water-based and other single-component paint Marking width 100-600mm adjustable Spray gun quantity 2 manual fixed spray gun Dimension 1780x980x1200mm Weigh 150Kg
Dy-hal-i/ii and dy-hal-iii/iv are hand-push airless cold solvent traffic lines marking machine, mainly used for small scale road line marking such as the zebra crossing marking, stop line, sports line, special letters and arrow mark, etc. 1. Firm welded frame chassis, is chrome-plated or corrosion resistant coating sprayed. Equipped with imported high-speed bearing, the whole machine is much lighter and more convenient. 2. Front wheel directional device can lock the front wheel to ensure the road-marking machine move freely in striping straight lines and turnings marking. 3. Adjustable guide rod can be freely adjusted up, down, to the left or right. 4. Equipped with high light warning lights makes the night working convenient. The flicker frequency can be freely adjusted, which greatly improved the safety of the marking work. 5. The new-type diaphragm type high pressure airless paint pump is with big flow and stable pressure. 6. Paint tank is with a build-in filter device and air in-take filter in the feeding port. 7. New-type manual spraying guns with reverse washed nozzle can make the road paint on-spot discharging easy and convenient. 1600*1200*1500mm(l*w*h)
We have 2units of Samsung (SD20) brand bulldozers brought from the Korean military. It's in good condition because it was brought from the military.
Handpush thermoplastic road marking machine's floor knife adopts imported hard tungsten steel knife-head with high viscidity and abrasion resistance, which makes the line edge facile and straight. 1.Marking shoe: Marking shoe and paint tank are integrally designed and hung inside frame of the chassis.The discharging port adopts double-closure to avoid leaking. Screeding knife made of fire resistance, abrasion resistance and oxidation resistance adopts screeding structure to make good quality markings, which ensures the head of marking more regular. Sieve in the paint tank effectively removes the impurity in it. The capacity of the shoe:65kg 2.Heating system: Petroleum liquified gas tank is used for respectively gas to front and back two row nozzles and outside inflame gun, whose power is controlled by different valves. The valves and gas tools adopt imported parts, and connection pipes are imported rubber pipes with heat and pressure resistance. 3.Glass beads bin: With gear transmission, the dispensing gear definitely rolls. Equip with automatic clutch device synchronous with screeding shoe; bin with windows can check the quantity of glass beads in time. The capacity: 30kg. 4.Chassis: Firm welding frame, the surface has been galvanized, chrome-plated or high temperature treatment. Equip with heat resistance (350), abrasion resistance modified rubber with the diameter 200mm, which can effectively prevent tackless or deformation after long time of high temperature work. The wheel nave is made of refined steel, and equip with high speed imported bearing, which makes the whole machine lighter and more convenient. 5.Handle bar: Individual design conforms to the requirements of human body project. The operation height can be adjusted according to the needs of the operator.
According to the engineering and construction experience, it is recommended that the conditions of use for marking for different roads, different regions, the choice of the traffic painting type and painting materials. applied. Solvent-based marking paint. It is a traditional type road marking paint, and it has the advantages of low cost, fast construction, easy to operate, adaptable, commonly used in urban road markings and less demanding provincial highway. Hot melt spray coating material. It is based on the thermoplastic hard resin-based material preparation, the powder room temperature. Construction of special equipment (thermal reactor) the coating is heated to 180 degrees Celsius to 220 degrees Celsius, the formation of a flowing liquid, coating the road to form a hard film. Hot melt marking paint contains reflective glass beads, reflective well. Hot melt spray-type marking film thin (8mm-2mn), construction speed, spray marking table uniform, neat edge, concept of linear Off. Anti-pollution performance is better than ordinary hot melt coating. By changing the coating material applied to the road of the city towel, and anti-pollution facilities after marking performance is greatly improved compared directly and room temperature coatings. Cracks are smaller than scratch-painting. Hot melt spray road marking paint used in the construction of low-pressure gas, centrifugal coating, marking after the film has no internal stress, at the same time marking the coating is thin, subjected to temperature changes caused by the shrinkage stress is relatively small. Higher value of anti-slip. Hot melt spray road marking is a uniform coating on the pavement, the marking surface after the completion of the original road, thus marking slip resistance. Henan dayu road marking machine Co., Ltd. was founded in 1992, is a leading professional traffic lanes coating facilitie manufacturer in China. Road machinery production base covers an area of 1.7 million square meters, with a construction area of nearly 100,000 square meters. Henan Dayu Road Marking Machinery Company, is internationally renowned lanes painting machines supplier, represented by special road lane construction machinery, highway road marking paint,and dedicated electronic traffic safety facilities,including thermoplastic spraying machines, cold solvent road marking machine, air-auxiliary lane coating equipment, two component road marking machines, auxiliary road marking equipment and kinds of traffic lines coating materials, respective for machine types. 20 kg
Road lines reflective principle is relied on the directional reflection effect of the glass beads sprayed and painted on the road surface. When the incident illumination enter into the glass beads body since the air is light-repellent substance, glass beads are optically dense substances, and thus produces the refraction phenomenon and deep fold to reflection within the lines coatings and in the contact surface of the glass and coatings. Features of dayu brand thermoplastic road marking materials 1. Fast drying and relatively good abrasion resistance: The road will be open to traffic after 10 minutes for its fast drying, and can be maintained for over six months. 2. Good adhesion: There will be no stripping on the condition of assure the road surface is dry and clean and film thickness before coating road materials on it. 3. Bright and beautiful: Bright in color and meet industry standard. Road Marked Lanes with no yellowing, discoloring, cracking, but strong visibility. 4. Convenient construction: No special requirement for construction machine. Both equipment painting and manual spraying type are proper. 5. Brand traffic marking materials are made of high quality raw material, and its whole production processes of thermoplastic machine paint are finished by completely automatic production line, absolutely avoid quality defects caused by artificial operation, such as over large mixture ratio, unstable quality, and further make sure the traffic coating paint of high quality to customers.
Model FHX-26 Marking width 10 ~ 450mm (adjustable) Spraying thickness 0.2 ~ 0.4mm Paint pump maximum flow 8L/min Max output pressure 250Bar Nozzle standard configuration 0.019 Max. Nozzle Size 0.025 High pressure pipe length 15m
Primer, a bonding material is used when making the heat fusion road markings. The prime can prevent the film from coming off and strengthen the adhesive force between the film and the road surface. Primer(sprayable) machine is the assistant equipment for drawing heat fusion markings. It chooses the gasoline engine as its power working together with the auto aircompressor to paint, which improves the working efficiency, meanwhile reduces the intensity of labor. It will not bring any noise or pollution. The guide bar of the paint gun can be adjusted up and down, in order to adjust the width of the paint accuratly and conveniently. The machine is easy to operate and maintain, moreover, its service life is long. Size: 800*400*850mm Net weight: 50kg
It is used in road marking. We make as per indian and European standards. 25kg hdpe bags.
