Mrinalini Industries

The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.

Pularin: Foot ball shaped 60 atoms of carbon at edges is layed in pularin.Pularin atoms are arranged in ball. Each atom is called Bucky balls and tubes are called Bucky tubes or Nano tubes.Each nano tube is 1 to 7 nm diameter i.e 1nm=50000 part of a hair sting. where? 1)mangampet ,cuddapah dist.Ap,India.app 800 ppm(parts prer million)info given by stanford University. Cost: 150 times costlier than gold. 10 grams pularin $23000 to $45000 also info given by Bucky-USA website. Special uses if this becomes common: 1)Pularin coting on aeroplanes withstands from thunders ,rains ,Flashes etc. 2)Bullet proof ackets 3)curing cancer etc.

We are leadding manufactrer and exporter of Brass and Metal swival ball joint.

Metal tin is mainly used in the manufacture of alloys. Tin and sulfur compounds - tin sulfide, which is similar in color to gold, is commonly used as a gold pigment. Tin's modern application is as a solder for the electronics industry. Used in various purities and alloys (often with lead or indium), tin solders have a low melting point, which makes them suitable for bonding materials. Standard ASTM B29-03, BS EN 12659:1999, GB/T 469 -2005 , Content Pb â?¥ 99.99 % Density 11.34 g / cm 2 Color Bluish Weight 35 kgs / lump, 55 kgs / lump Dimension 21" x 4" x 2.5" Package Standard Sea-worthy package, fixed by belt per ton Shape Rectangular Lump Application lead-acid storage batteries Ammunition, cable sheathing, and building construction materials counterweights, battery clamps cast products such as: bearings, ballast, gaskets, type metal, terne plate, and foil Container Size 20Gp - 2.352(width) *2.385 ( Height ) * 5.90 ( Inside length ) Meter 40Gp - 2.352(width) *2.385 ( Height ) * 11.8 ( Inside length ) Meter 40HQ - 2.352(width) *2.69 ( Width ) * 5.90 ( Inside length ) Meter

1,Hight prurity (99.99% min) Metal Antimony (Sb) 2,4N>99.99%, 5N>99.999%, 6N>99.9999%, 7N>99.99999% 3,Lumps/Ingot/Granule/Bar 4,Color: Gray 5,Atomic weight: 121.760 6,Electronegativity: 2.05 7,CAS No.: 7440-36-0 8,Density: 6.697 g/cm3 (25â??) 9,Melting Point: 630.63 â?? 10,Boiling Point: 1587 â?? 11,Mainly used for the preparation of â?¢ - V compound semiconductor InSb, Bi2Sb, GaSb, high purity alloys, electronic refrigeration element materials and germanium, silicon single crystal dopants.

We are very well producer of rubber roll sheet in Korea for satisfying the requirements below conditions Thickness:10~80mm Width: Min 910~ Max1,500mm Length: 10~30m Color: as your request excepting white Material: Natural rubber, SBR, EPDM as your request

Raw melting material - aluminum scraps, cans, engine waste etc. Output capacity - 5-30 tons/h, customized Automation - Full automatic/ half automatic (based on output requirement and investment budget Ingot type - ADC12 (7.5kg/ 10kg / customized) 1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift; 2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing. Every lot of production need to do testing . 3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water. 4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500 5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.