Maruti Alluminum Pvt. Ltd.

We are supplier and exporter of Copper Slag. Copper slag is a low cost expendable abrasive suited for open blast cleaning and due to its low silica content it does not pose the health hazards created by silica sand. Its sharp, hard particles can provide a fast cleaning action and an excellent surface profile. It is available in various sizes Copper slag is abrasive blasting grit made of granulated slag from metal smelting processes (also called iron silicate). Copper slag abrasive is suitable for blast cleaning of steel and stone/concrete surfaces, removal of mill scale, rust, old paint, dirt etc. Suitable for SA-3, SA-2 and SA-2. Copper slag blasting media/grit is manufactured of the granulated slag of copper refineries, and used for blast-cleaning of metal surface. In different industries it is called different names abrasive powder, grit, copper slag grit, mineral grit, grinding grains, etc.

CHEMICAL COMPOSITION ELEMENTS CaO% MgO% SiO2% Al2O3% TFe% MnO% Cr2O3% P2O5% S% MIN 24.00 3.50 10.00 2.00 11.00 0.02 0.00 0.02 0.05 MAX 49.00 25.00 28.00 12.00 36.00 2.50 0.80 0.42 0.20 TYPICAL 39.20 12.20 16.80 4.60 21.70 1.25 0.12 0.28 0.12 PHYSICAL APPEARANCE ASPECT Agglomerate materials COLOR Gray blackish color CHEMICAL BEHAVIOR The basicity of the slag is normally fixed by the amount of lime and calcinated dolomite added, the silicon and aluminum levels of the hot metal and steel scrap charged as well as ferro-alloys. Below present our general procedures for the purchase and sale of sugar of Brazilian origin: 1- Buyer issues a Letter of Intention (LOI) addressed to Seller; 2- Seller issues a Soft Corporate Offer (SCO); 3- If Buyer accepts SCO, signs and seals SCO and then sends to Seller; 4- Seller issues Full Corporate Offer (FCO); 5- Buyer signs and seals FCO and issues an Irrevocable Corporate Purchase Order (ICPO), addressed to Seller; 6- Seller issues draft of Sale and Purchase Agreement (SPA) to be discussed and commented; 7- SPA is signed by Seller and Buyer; 8- Buyer issues draft of the Payment Instrument (SBLC/DLC) for approval by Seller�´s Bank; 9- If Seller�´s Bank accepts, Buyer issues the bank guarantee (SBLC/DLC); 10- Seller issues Performance Bond (PB) 2%; 11- Seller prepares the product and export documents; 12- Buyer receives the export documents by mail; 13- Buyer makes payment 100% to Seller�´s Bank through transfer bank (Swift Message MT-103); 14- Shipping; 15- Seller sends the original export documents to Buyer; NOTES: The financial instrument (SBLC / DLC) must be issued by the Top 50 Bank in the world ranking.

Welcome to Gremlog Trading DMCC, your premier source for high-quality slag material. As a leading name in the distribution of industrial materials, we pride ourselves on offering superior products that meet the diverse needs of our global clientele. Slag, often referred to by various names such as clinker, dross, fly ash, or ground granulated blast furnace slag (GGBFS), is a valuable by-product of metal smelting processes, particularly from steel and iron production. This versatile material has a wide range of applications, making it an essential component in various industries. From construction and road building to cement production and environmental remediation, slag's unique properties enhance durability, strength, and sustainability.

GGBFS Ground granulated blast furnace slag (GGBFS) The ground granulated blast furnace slag (GGBFS) is a by-product of iron manufacturing which when added to concrete improves its properties such as workability, strength and durability. This material is obtained by the heating of iron ore, limestone and coke at a temperature about 1500 degree Celsius. The process is carried out in a blast furnace. The formation of GGBFS is not direct. The by-product of iron manufacturing is a molten slag and molten iron. The molten slag consists of alumina and silica, also with the certain amount of oxides. This slag is later granulated by cooling it. For this, it is allowed to pass through a high-pressure water jet. This result in quenching of the particles which results in granules of size lesser than 5mm in diameter. The main constituents of blast furnace slag are CaO, SiO2, Al2O3 and MgO. These are the minerals that are found in most of the cementitious substances. The particles are further dried and ground in a rotating ball mill to form a fine powder, known as ground granulated blast furnace slag cement. Now different methods can be employed to perform the main process called as the quenching. Applications & Benefits of GGBFS: In concrete: The incorporation of ground granulated blast furnace slag in concrete manufacture gains many advantages which are mentioned below: GGBFS in concrete increases the strength and durability of the concrete structure. It reduces voids in concrete hence reducing permeability GGBFS gives a workable mix. It possesses good pumpable and compaction characteristics The structure made of GGBFS constituents help in increasing sulphate attack resistance. The penetration of chloride can be decreased. The heat of hydration is less compared to conventional mix hydration. The alkali-silica reaction is resisted highly. These make the concrete more chemically stable. Gives good surface finish and improves aesthetics. The color is more even and light. Lower chances of efflorescence. The maintenance and repair cost of structures are reduced thus increasing the life cycle of concrete structures. Unlike cement, GGBFS does not produce carbon dioxide, sulphur dioxide or nitrogen oxides. White Cement: White Portland Cement is of high quality, whiteness and strength, it essentially has the same properties and characteristics as gray cement, except for color. It is widely used in numerous applications such as precast concrete, cast-in-place concrete, terrazzo, median barriers, curbs, tile grout, paint, masonry units, swimming pools, glass fibre reinforced surface bonding mortars.

Aluminum ingots A7, A8. Aluminum ingots P0202A, P0303A, P0404A, P0506A, P0610A, P1020A. Aluminum ingots 46000, 46100, 47100. Aluminum ingots 6063. Etc. Product Description : Aluminum is also theoretically 100% recyclable with no loss of its natural properties. It also takes 5% of the energy to recycle scrap aluminum then what is used to produce new aluminum. The most common uses of aluminum include: Aluminum is the third most abundant metal in the Earth’s crust, and the third most abundant element overall. No other metal can compare to Aluminum when it comes to its variety of uses. Some uses of aluminum may not be immediately obvious; for example, did you know aluminum is used in the manufacturing of glass? Aluminum popular features: Lightweight · Strong · Resistant to corrosion · Durable · Ductile · Malleable · Conductive · Odorless Price of product ( USD price or FOB price) : Monthly quantity at least 3.000 MT. Best price over 5.000 MT monthly. Selling price LME Less 20% . Product origin : Russia and Non Russia Key Specifications/Special Features : Aluminum A7/A8 GOST 11069-74 Quality Value demanded by norm GOST 11069-74 A7 A8 Al Min. 99,7% Min. 99,8% Fe Max. 0,16% Max. 0,11% Si Max. 0,15% Max. 0,08% Cu Max. O,01% Max. 0,01% Zn max. 0,05% Max. 0,05% Ti max. 0,02% Max. 0,02% Minimum Order Size and Packgaing details : Bulk in tanker vessels. Tanks 20 MT.