Coal base activated carbon Coal based activated carbon can be divided into pellet carbon, granular carbon, impregnated carbon, acid washed carbon, powder carbon and briquette carbon etc, more than 6 kinds and hundreds of specifications.The products can be used in desulfurization, solvent recovery, catalyst carrier, water treatment, air purification, all-purpose protection etc. The characteristics of the products based on the developed micropores of Taixi coal inherent, adjusting pore and making transition hole and large pore distribution extent according to customers demands. It has been a breakthrough in only use etheric western coal as raw material to produce before, and now the raw material species covering Inner Mongolia Shangxi and other kinds of coal. Pellet carbon Pellet carbon can be supplied from the range of 0.9mm to 9.0mm in diameter according to clients requirement. This king of carbon is made of high standard Taixi anthracite, processed through grinding, mixture, extrusion, carbonization and steam activation etc. Due to the high huge specific surface area, it can be widely used in both of gas-phase and fluid-phase purification and adsorption, catalyst carrier, poison and security protection. Main Technical Parameters of Pellet Activated carbon Spec Type Diaï¼?mmï¼? Ashï¼?%ï¼? Hardnessï¼?%ï¼? Densityï¼?G/Lï¼? CTC ï¼?mmï¼? Lodineï¼?MG/Gï¼? Water Soluble Ashï¼?%ï¼? HA-0.9 0.9 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-1.5 1.5 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-2.0 2.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-3.0 3.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-4.0 4.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-5.0 5.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-6.0 6.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-7.0 7.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-8.0 8.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 HA-9.0 9.0 2-15 â?¥90 300-600 25-125 500-1300 â?¤0.5 Granular Activated Carbon Granular Activated Carbon is the extension and supplement on products manufacturing and service of pellet series. This type of activated carbon is finished by machanical breaking and screening of pellet series, therefore, it has the pore characteristics of pellet activated carbon. Normal specification including 8X30meshã??12X40meshï¼?5X7meshï¼?12X30meshã??20X40mesh etc. Main Technical Parameters of Granular Activated Carbon Ashï¼?%ï¼? Hardnessï¼?%ï¼? Densityï¼?G/Lï¼? Lodineï¼?MG/Gï¼? Methylene Blueï¼?MG/Gï¼? Water Capacity(%) Water soluble ash ï¼?%ï¼? 5-15 â?¥85 350-500 800-1100 180-250 80-110 â?¤0.5 Powder Activated Carbon Powder Activated Carbon is grind into suitable powder size with qualified activated carbon. Because of its powder state, better diffusivity, it can full touch to the reaction material. Meantime, it is applying to disposable recovery treatment of filling water and industrial waste water with its high efficient adsorption, moreover, also used for refining and decolorization of liquid. The types including 30X200meshï¼?60X200meshï¼?100X200meshï¼?325mesh etc.
It is made from well-selected Ningxia Taixi anthracite, used to add the carbon content of the burned steel during the smelting process. Mainly used for electrical manufacturing and foundry industry. Spe Grad F.C(%) Ash(%) Moisture(%) V.M(%) S(%) N(%) Size Super Grade 95min 4.0max 0.5max 1.0max 0.25max 0.3max . As clients' demands. 1st Grade 94min 4.5max 0.5max 1.0max 0.25max 0.3max 2nd Grade 93min 6max 1.5max 1.5max 0.3max 0.4max 3rd Grade 92min 6.5max 1.5max 1.5max 0.35max 0.4max 4th Grade 90min 8.5max 1.5max 1.5max 0.35max 0.4max 5th Grade 85min 13max 3max 1.5max 0.4max 0.4max 6th Grade 80min 16max 3max 1.5max 0.4max 0.4max Packing . As clients' demands.
It is calcined by asphalt coke and sponge coke in the 1350ºC calcined kiln,which is obtained the lower volatile matter products. Widely used in chemical smelting, mechanical casting, petroleum exploration and other industries.     Spe Grad F.C(%) Ash(%) Moisture(%) V.M(%) S(%) N(ppm) Size CPC 98min 0.5max 0.5max 0.7max 0.7max 1000-2000max . As clients' demands. CPC 98min 0.5max 0.5max 0.7max 0.5max 1000-2000max CPC 98min 0.5max 0.5max 0.7max 0.1max 1000-2000max Packing . As clients' demands.
It is made from low sulfur and low nitrogen petroleum coke by 2,500-3,500ºC temperature graphite annealing. As a high-purity carbon material, it has characteristics of high fixed carbon content, low sulfur, low ash, low resitance etc. It can be used as carbon raiser (Recarburizer) to produce high quality steel, cast iron and alloy.     Spe Grad F.C(%) Ash(%) Moisture(%) V.M(%) S(%) N(ppm) Size GPC 98.5min 0.5max 0.5max 0.5max 0.05max 300max . As clients' demands. Packing . As clients' demands.
We are supplier and exporter of Activated Carbon. Granular Activated Carbon Products range from the size 0.2mm to 3.75mm. Granular Activated Carbon has relatively larger particles size compared to powdered activated carbon and consequently, presents a smaller external surface. Powdered Activated Carbon Powdered Activated Carbons are small activated carbon particles, with a size that is predominantly less than 0.075 mm. Activated Carbon is used worldwide in purification of Water, Air, etc. We are producers Dura specie of Palm Kernel Shells Powder & Pellets Activated Carbon, with over 1600 Iodine level and equally high level of Harness.
We are exporter of Activated Carbon. Activated carbon made from raw organic material such as coconut shell. The raw material of activated carbon pulverized and sieved into appropriate and uniform particle sizes. Carbon has been used as an adsorbent for centuries. Activated carbon is a particularly good adsorbent due to its high surface area to volume ratio.
Carbon Blocks used in furnace having a great alternative against Petcoke. As it has high melting power and cheap as compared to Petcoke. Here in India, we are a supplier and exporters of Carbon blocks. Parameters- Total moisture (Mt): 1.80% Ash(Aad): 13.07 Volatile matter (Vad): 13.94 Fixed Carbon (FCad): 77.88 Sulfur (S): 3.10
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�¯�¿�½?�?�°C to 1250�¯�¿�½?�?�°C with a boiling point of 2355�¯�¿�½?�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
We are exporter of Ferro Silicon. FerroChrome is a kind of Ferro alloy which is formed by Ferro and Chrome,it is an important alloy addition in steel making. Ferrochrome (Fe Cr) is an alloy of chromium and containing between 50% and 70% chromium.
