FDR-3301 UV fluorescence sulfur analyzer Scope UV fluorescence sulfur analyzer is based on UV fluorescence measurement principle and the development of computer technology combined with a new generation of precision instruments, is currently the most advanced of the total sulfur content tester, in line with ASTM D5453, SH / T 0689 and other standards, the instrument is National total sulfur content of refined oil arbitration standards. Now widely used in the determination of total sulfur content of crude oil, hydrocarbons and fuel, petroleum, plastics, petrochemicals, food and so on. Measurement principle instrument uses ultraviolet fluorescence method, when the sample is introduced into the pyrolysis furnace, cracking occurred sample oxidation of sulfide which quantitatively converted to sulfur dioxide, carried by a carrier gas, off which the water through a membrane dryer, into the reaction chamber, sulfur dioxide absorbing ultraviolet light energy into an excited state of sulfur dioxide (SO2 *), the fluorescence emission of sulfur dioxide when SO2 * to return to a stable state, the energy released by a photomultiplier tube to receive, and then the micro-current amplifier, computer data processing, the amount of reaction with sulfur dioxide emission intensity is proportional to the amount of sulfur dioxide and total sulfur content in the sample is proportional, so the content of the sample can be determined by measuring total sulfur emission intensity. Features 1, computer-controlled operation, enabling interactive, data, peak shape can be automatically stored print. 2, the operating software can be connected with LIMIS system, automatic data transmission. 3, the instrument uses the new quartz pyrolysis tube, the injection volume can be increased to reduce measurement errors, increase the sensitivity of the instrument, higher repeatability. 4, cooling fans, automatic switch, eliminating the need to wait for the shutdown to finish samples trouble, saving time and effort. 5, darkroom system uses the latest technology, the key components imported detecting element to improve the detection accuracy and sensitivity of the instrument. Technical Parameters 1, in line with standards: ASTM D5453, SH / T 0689 and other standards 2, measuring range: 0.2mg / L ~ 10000mg / L ~ percentage 3. Air source: Argon: 99.999% Oxygen: 99.999% 4, sample status: solid, liquid, gas (with corresponding injector) 5, temperature range: room temperature ~ 1100 ? ± 3 ? 6, repeatability error: 0.2mg / L=X
Little Sulphurously Fuel Oil For Firebox
Origin: Kazakhstan, Georgia, Malaysia Incoterms: CIF/FOB Loading Port: Rotterdam and Houston etc Payment Terms: MT103 TTWIRE Performance Bond: 2% PB Contract Term: SPOT 6-12 Month Minimum (With Rolls and Extension Inspection: SGS CIQ or Similar Low Sulfur Fuel Oil Quantity: 5,000 MT - 50,000 MT Trial Lift Quantity: 100,000 MT - 200,000 MT per month x 12 months Price CIF/ASWP: Gross USD $455.00 MT / USD $445.00 MT NET TRANSACTION WORKING PROCEDURE FOB Rotterdam/Houston 1. Buyer sends Company Profile along with ICPO, Tank Storage Agreement (TSA) and data page of buyers passport 2. Seller Issues commercial invoice (CI), Buer signs and returns commercial invoice back to seller. 3. Seller verify buyer TSA by Letter and Seller issues the following POP documents to buyer: a)Statement of Product Availability b)Commitment Letter of Supply c)Unconditional Dip Test Authorization (UDTA) d)Authorization to Sell and Collect (ATSC) e)Authorization to verify the product in Seller''s tank (ATV) f) Fresh SGS not older than 72 hours 4. NCNDA/IMFPA will be signed among all parties involved. 5. Buyer options conduct DIP TEST on the product and make the payment for the total value of product injected into the tanks through the means of mT103-TT 6. Seller pays commission to all intermediaries involved in the transaction and subsequently monthly shipment continues as per terms and conditions of the commercial invoices and extension of transaction by issuing 12 months contract to buyer for proceeding. STAND TRANSACTION CIF PROCEDURES 1. Seller confirms ICPO + passport of buyer and issues FCO for signing 2. Seller issues contract for amendment and countersigning as per mutual agreement. 3. Seller legalizes and register contract at seller expense and send to buyer as final approved, registered and legalized contract 4. Seller sends to buyer via e-mail, the following POP documents in buyer''s name for verification of the allocation: A. Statement of product availability B. Refinery commentment to supply C. Company profile D. MSDS E. Company license to export 5. Buyer and Seller sign the CPA with the secured shipping company for documentation along with the NCNDA and IMFPA for commission construction
Origin: Kazakhstan, Georgia, Malaysia Incoterms: CIF/FOB Loading Port: Rotterdam and Houston etc Payment Terms: MT103 TTWIRE Performance Bond: 2% PB Contract Term: SPOT 6-12 Month Minimum (With Rolls and Extension Inspection: SGS CIQ or Similar Ultra Low Sulfur Fuel Oil Quantity: 5,000 MT - 50,000 MT Trial Lift Quantity: 100,000 MT - 200,000 MT per month x 12 months Price CIF/ASWP: Gross USD $495.00 MT / USD $485.00 MT NET TRANSACTION WORKING PROCEDURE FOB Rotterdam/Houston 1. Buyer sends Company Profile along with ICPO, Tank Storage Agreement (TSA) and data page of buyers passport 2. Seller Issues commercial invoice (CI), Buer signs and returns commercial invoice back to seller. 3. Seller verify buyer TSA by Letter and Seller issues the following POP documents to buyer: a)Statement of Product Availability b)Commitment Letter of Supply c)Unconditional Dip Test Authorization (UDTA) d)Authorization to Sell and Collect (ATSC) e)Authorization to verify the product in Seller''s tank (ATV) f) Fresh SGS not older than 72 hours 4. NCNDA/IMFPA will be signed among all parties involved. 5. Buyer options conduct DIP TEST on the product and make the payment for the total value of product injected into the tanks through the means of mT103-TT 6. Seller pays commission to all intermediaries involved in the transaction and subsequently monthly shipment continues as per terms and conditions of the commercial invoices and extension of transaction by issuing 12 months contract to buyer for proceeding. STAND TRANSACTION CIF PROCEDURES 1. Seller confirms ICPO + passport of buyer and issues FCO for signing 2. Seller issues contract for amendment and countersigning as per mutual agreement. 3. Seller legalizes and register contract at seller expense and send to buyer as final approved, registered and legalized contract 4. Seller sends to buyer via e-mail, the following POP documents in buyer''s name for verification of the allocation: A. Statement of product availability B. Refinery commentment to supply C. Company profile D. MSDS E. Company license to export 5. Buyer and Seller sign the CPA with the secured shipping company for documentation along with the NCNDA and IMFPA for commission construction
Scope Petroleum product sulfur content analyzer (x-ray spectroscopy) is in accordance with people's republic of china standard gb / t11140, gb / t17040, astm d4294 requirements specified in design and manufacture of this instrument for the determination of trace sulfur content of petroleum products. Because it uses physical analysis methods, with fast analysis without complicated sample pretreatment, high precision, human error is small, low labor intensity of operators, no pollution, it has been widely used and generally replace other measuring sulfur in the international arena the analytical method. Features 1, with full english operating system, the man-machine interface friendly exchanges. 2, short detection time, automatic test results within 30 seconds; automatic c / h ratio correction, for a variety of samples; 3, large-screen lcd, automatic print measurement data; 4, using the x-ray tube excitation, the instrument can be long-term use, without affecting the source attenuation; 5, the use of physical methods, the analysis does not touch, do not destroy the sample, no chemical reagents; 6, instrument with integrated design, easy maintenance; Technical parameters 1, the scope of analysis: s analysis range can be adjusted by the calibration curve of the selected method. 2, the scope of analysis width: s% max-s% min=9.999%; such as oil: s: 0.001 ~ 9.999%. 3, the inherent error, accuracy of analysis: such as oil: in line with the national standard gb / t 17040, at the same time meet the relevant requirements of american national standard astm d4294. 4, system analysis time: 1 to 999 seconds, the recommended value of 60 seconds. 5, detection limit: 10ppm 6, using the conditions: ambient temperature: 5 ~ + 40 ?, relative humidity: =85% (30 ?), power supply: 220v ± 20v, 50hz. 7, total power consumption:
FOB MOQ. : 50.000MT PRICE : USD430/MT Commision : US$ 5/ MT for Buyer's Side US$ 5/ MT for Seller s Side TRANSACTION PROCEDURES 1. Buyer issues Company Profile ICPO Buyer's Passport and Tank Storage Agreement TSA 2.Seller verifies Buyer Company and Registration including Buyer's TSA and issues Commercial Invoice for the trial delivery. 3.Upon Buyer sign back of Commercial InvoiceBuyer request buyer's tank farm invoice for injection time to Seller. 4.Seller processes payment to Buyer's tank farm per the invoice and issues Injection Schedule and pays for the Injection Fee and Buyer's tank farm issues TSR and ATV. 5.Upon completion of injection into Buyer's tanks by seller, Seller issues DTA in the same day. 6.Buyer conducts the dip test at Buyer's expense. 7.Upon successful inspection report of Q&Q, Seller issues ATSC and Certificate of Origin to Buyer and Buyer pays for the product in full by Mt103/TT within 24 hours and Seller transfer the Title. 8.Seller and Buyer sign 12 months contract.
Scope UV fluorescence sulfur analyzer is based on UV fluorescence measurement principle and the development of computer technology combined with a new generation of precision instruments, is currently the most advanced of the total sulfur content tester, in line with ASTM D5453, SH / T 0689 and other standards, the instrument is National total sulfur content of refined oil arbitration standards. Now widely used in the determination of total sulfur content of crude oil, hydrocarbons and fuel, petroleum, plastics, petrochemicals, food and so on. Measurement principle instrument uses ultraviolet fluorescence method, when the sample is introduced into the pyrolysis furnace, cracking occurred sample oxidation of sulfide which quantitatively converted to sulfur dioxide, carried by a carrier gas, off which the water through a membrane dryer, into the reaction chamber, sulfur dioxide absorbing ultraviolet light energy into an excited state of sulfur dioxide (SO2 *), the fluorescence emission of sulfur dioxide when SO2 * to return to a stable state, the energy released by a photomultiplier tube to receive, and then the micro-current amplifier, computer data processing, the amount of reaction with sulfur dioxide emission intensity is proportional to the amount of sulfur dioxide and total sulfur content in the sample is proportional, so the content of the sample can be determined by measuring total sulfur emission intensity. Features 1, computer-controlled operation, enabling interactive, data, peak shape can be automatically stored print. 2, the operating software can be connected with LIMIS system, automatic data transmission. 3, the instrument uses the new quartz pyrolysis tube, the injection volume can be increased to reduce measurement errors, increase the sensitivity of the instrument, higher repeatability. 4, cooling fans, automatic switch, eliminating the need to wait for the shutdown to finish samples trouble, saving time and effort. 5, darkroom system uses the latest technology, the key components imported detecting element to improve the detection accuracy and sensitivity of the instrument. 6, equipment imported membrane dryer to absorb , eliminating the need to frequently replace magnesium perchlorate of trouble, while reducing the leakage problem. 7, using computer control of temperature, improve the instrument precision temperature control, and difficult to over-temperature. 8, using air instead of water cooling, saving water resources. 9, can be adjusted to take existing calibration curve calibrated using a standard sample after sample analysis. Technical Parameters 1, in line with standards: ASTM D5453, SH / T 0689 and other standards 2, measuring range: 0.2mg / L ~ 10000mg / L ~ percentage 3. Air source: Argon: 99.999% Oxygen: 99.999% 4, sample status: solid, liquid, gas (with corresponding injector) 5, temperature range: room temperature ~ 1100 ? ± 3 ? 6, repeatability error: 0.2mg / L=X
FUEL OIL HIGH SULFUR
Base oil can be obtained from oil or non-oil sources. virgin base oil obtained from crude oil .Since most of the base oil used in the production of lubricants obtained from oil resources. base oil properties of the oil obtained is dependent on the type of crude oil and refining operations. base oil is chemical components during the refining process of crude oil from which it obtained, to inherit. Since crude oil containing different combinations such as paraffinic hydrocarbons, naphthenic and aromatic sulfur compounds are also, base oil are also made up of these compounds. base oil composition comprising a major effect on the properties of spent oils, paraffinic compounds, naphthenic and aromatic
ESPO (Eastern Siberia-Pacific Ocean) oil is a premium blend of crude oil primarily exported from Russia. This light, sweet crude has gained significant traction in the global market. ESPO oil is extracted from fields in Eastern Siberia and transported via the Eastern Siberia-Pacific Ocean pipeline. Pipeline: The ESPO pipeline, stretching from Taishet in Irkutsk Oblast to the Pacific port of Kozmino, facilitates the transportation of this crude. ESPO crude has an API gravity typically around 34-35 degrees, classifying it as a light crude oil. It has a low sulfur content, usually between 0.5% and 0.6%, making it a sweet crude. This low sulfur content is advantageous for refining into high-quality fuels with lower environmental impact. ESPO oil is known for its low metal and salt content, further enhancing its desirability for refineries seeking to produce cleaner fuels. ESPO crude often commands a premium price compared to other Russian crude grades like Urals, due to its superior quality and favorable location. Pricing for ESPO oil is typically benchmarked against Dubai/Oman crude prices. Espo has low sulfur content in ESPO oil translates to lower sulfur dioxide emissions when refined, contributing to reduced environmental impact compared to higher sulfur crude oils. Price: FOB $68/$64 CIF $65/$61 Availability: In Stock Origin: Russia / Kazakhstan. For more details contact us.