Bricks
Capacity 100,000m2/y-450,000m2/y Automation Full automatic Fuel Natural gas, heavy oil, coal and diesel Drying method Dry by air Hot air stove drying system Main raw materials Gypsum powder, water Product dimension Thickness: 70mm-200mm Width: 300mm-500mm( adjustable) Length: 620mm,666mm We can design and manufacture products of other dimensions as clients'special requirement Standard of product quality In conformity with national standard JC/T698-2010
Aluminum content: 25-42% Compressive strength at room temperature: 30-45MPa Standard brick size: 230*115*65mm Cost-effective: The phosphoric acid impregnated products of blast furnace clay bricks with good thermal stability and qualified quality after drying treatment and secondary low temperature firing can be used for masonry of the upper part of the blast furnace furnace lining.
Color : Brown Shape : Square Width : 14 Inches Height : 14 Inches Material : Refractory materials
Supplier: Refractory bricks, high alumina bricks, fire clay bricks, sk 34 fire bricks, sk 36 fire bricks, acid resistance bricks,insulating bricks, hfk bricks, cfi bricks, special shaped refractory burner block, refractory tiles, refractory tundish well blocks, refractory nozzle, refractory castables, medium purity high purity castables, low cements castables, refractory mortar, refractory cements, ceramics fiber blankets, ceramics fiber boards, crushed refractory bed materials, bottom pouring sets
Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
Supplier: High alumina bricks, refractory clay bricks, phosphate insulation materials,metallurgy, coke, electric power, cement, building materials, glass, ceramics, carbon roasting, chemical fertilizers and refractories for industrial furnaces
A brick is a type of construction material used to build walls, pavements and other elements in masonry construction. Block is a similar term referring to a rectangular building unit composed of clay or concrete, but is usually larger than a brick
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
POWER OF CONCRETE HARDENER (SILVER) It is now possible to dispatch solid blocks / Bricks in just 24 hours of time with great strength AND also to demould pavers / tiles in just 9 hours of time by using - BEST HARDENER - (ISO 9001-2015 CERTIFIED COMPANY) Super strong binding Most Economical hardener 100% Guaranteed Results Self curing ability Increase in Strength by 25-30%
