Expanded or not Unexpanded Packing Ton Bag Application 1. Heat/sound/low-temperature/oxygen preservation or insulation material in various fields 2. Foundry material as covering agent to clear up slag for metal casting 3. Perlite filter aid used in foundry, food, drink, medicine, chemical,etc. 4. Agricultural / horticultural / hydroponics /soilless culture perlite as seedings growing media
Expanded or not Unexpanded Packing Ton Bag Application 1. Heat/sound/low-temperature/oxygen preservation or insulation material in various fields 2. Foundry material as covering agent to clear up slag for metal casting 3. Perlite filter aid used in foundry, food, drink, medicine, chemical,etc. 4. Agricultural / horticultural / hydroponics /soilless culture perlite as seedings growing media
Supplier: Slag remover, perlite, carbon additive, expanded compound
Product Properties 1ï¼?High purity - Control the consistency of raw material from the mine resource. - Introduce automatic whole-process equipment to ensure product consistency. 2ï¼? Good performance - Increase globular graphite amount in the nodular cast iron significantly to promote the graphitization; - Increase the graphite crystal nucleus of molten iron, refine graphite in the matrix for more uniform distribution; 3ï¼?Fine classification - Various product category, to provide cu stomized carbon raising scheme 4ï¼?Cost-saving - Reduce the usage amount of iron, increase scrap consumption, and save raw material cost. How to use 1ï¼?For 1-5 T furnace: - while a small amount molten iron in the furnace, - or with some molten iron remained, add the carbon additive one-time, - then add the other material. which can make carbon additive fully absorbed. 2ï¼?For greater than 5 T furnace: - mix proper carbon additive with charging material as suggested first, - and then along with the increase of charging material gradually, - that is, before the molten metal rising up to about 2/3 height of furnace, - all carbon additive shall be added. It guarantees sufficient melting & absorbing time before molten metal out, and improves the absorption of carbon.
Supplier: Slag remover, perlite, carbon additive, expanded compound
Introduction of recarburizer Recarburizer is a kind of additives used in steelmaking, casting, is an essential part of raw materials, production of high quality steel electrode paste are in addition to production of raw materials. Recarburizer there are many kinds of raw materials, production process is different, have wood carbon, coal carbon, coke, graphite, etc, among them under various classification and there are a lot of small type. High quality recarburizer generally refers to after graphitization of carburant, under the condition of high temperature, carbon atoms arranged in the microstructure of graphite, so called the graphitization. Graphitization can lower the content of impurities in the carburant, improve the carbon content of carburant, reduce sulfur content; Apply to cast iron (steel) and carbon, grey iron casting high carbon, low sulfur, low water content and the characteristics of low cost and high cost performance.
How to Use 1), For 1-5 T furnace: - while a small amount molten iron in the furnace, - or with some molten iron remained, add the carbon additive one-time, - then add the other material. which can make carbon additive fully absorbed. 2), For greater than 5 T furnace: - mix proper carbon additive with charging material as suggested first, - and then along with the increase of charging material gradually, - that is, before the molten metal rising up to about 2/3 height of furnace, - all carbon additive shall be added. It guarantees sufficient melting & absorbing time before molten metal out, and improves the absorption of carbon.
We are proposing about 2000tons of iron slag derived from the desulphurisation skimming process. This material is a iron by- product that is encapsulated in varying levels of contaminants (S,Mg,Si). In order to enhance its usability, the material is processed and screened. We can propose two specifications of Iron Slag - European Code: 19.12.01 - Basel Code: B1010 - HS Code: 2619.0020 - Quantity: 2000 tons currently available - Monthly quantity: 500-1000 tons depending on production - Size: 350 1200 mm - Fe content: from 77 to 86% - C content: above 2,5-3% - Bulk density: 2,8-3,4 tons/m3 - Loading type: loose in 20 (26-27 tons on average) The level of Fe% in the slag has been estimated by water displacement test. For any further information please feel free to contact us
This Cast Iron slag is a by-product derived from the production of thermal insulating products. The byproduct is a ferrous slag which can be utilised in an electric arc furnace to produce crude steel. Physical Description On visual inspection, it appears to be made up of irregular shapes. Dimension: 500mm -800mm Chemical Composition Its chemical composition is homogeneous and stable with Fe contents in the range of 90 +/- 5% and P contents < 0.6% S around 0.15% and C% around 3.5%. Packing: Loose in container Loading: in 20 Container For further information, please feel free to contact us.
