The AZ series centrifugal horizontal slurry Pump is Chinese design slurry pumps. It is advanced designed in oil lubricated frame could be more steady work in high pressure or the pumps in series. The impeller design is advanced and could be adjusted according to the requirement of the work site instead of using different type of pumps which is Min the pump and parts required and much easy to use and main. The AZ series centrifugal horizontal slurry Pump is widely used in power plant, metallurgy, mining, coal, building material and chemical industries to deliver abrasive fluid which is the best choice for updating old design slurry pumps! -!
1.Reasonable structure, convenient repair: pump head part is used for before and after the door structure, repair without dismantling piping, just move the motor backwards, can be disassembled and repair the pump. 2.High concentration, no clogging: conveying pulp concentration up to 6%; 3. Cavitation erosion resistance, long service life: the actual service life than ordinary paper pulp pump can be increased by 2-3 times; 4. High efficiency, energy saving: efficiency than ordinary pulp pump average of 3-10 percentage points, saving energy and reducing consumption, up to 15-30% . 5. The impeller and the guard board clearance can be adjusted in a timely manner, maintain higher working efficiency. The pump above the pump body is larger, the structure of open, disassembly and convenient maintenance. 6. Application of water rinse to prevent clogging the pump is stopped. 7. The type of pump in addition to 12PN mud export level, others are vertical upward. 8. PN type pump shaft seal water must be added a certain amount of water, the general work flow of 1-3%, the pressure should be greater than the working pressure of 1 kg / cm 2. 9. 1PN, 2PN, 3PN, 2PNL, 3PNL steering motor direction is clockwise, 4PN, 6PN, 8PN, 10PN, 12PN steering motor direction is counter clockwise. 10. In this type of pump in general use. 11. The PN Horizontal Centrifugal Submersible Slurry Water Mud Pump is not allowed to reverse parking. -
Basically we are dealing with Centrifugal Pumps 1.Water Pumps-WP Operating Range Delivery Size:DN 32 to 150 mm Capacity:upto 550 m3/hr Head:upto 100m Temperature:upto 160° C Pressure:upto 16 bar Design: Horizontal, radial split, volute casing pumps according to DIN 24255 std. with closed impeller, end suction, top centre line discharge. Back pull out design enables to remove the rotor without disturbing the pipelines. Application: For handling clean or slightly turbid non-aggressive liquids. Suitable for pumping condensate, general water supply in agriculture, trade, and industries with favourable NPSH condition. Materials: Cast Iron and Bronze. 2.Chemical Process Pump Operating Range Delivery Size DN 25 to 200 mm Capacity:upto 700 m3/hr Head:upto 180m Temperature:upto 260° C Pressure:upto 26 bar Design: Horizontal, radial split, volute casing pumps according to ANSI B73-1 specifications with open impeller, end suction, top centre line discharge. Simple external axial adjustment for impeller wear. Back pull out design enables to remove the rotor without disturbing the pipelines. If a spacer coupling is used, the motor does not have to be removed from the base plate. Only four bearing beds cover the entire 32 models. This means that the shafts, sleeves, bearings, and bearing beds are identical in and interchangeable for a large number of pump sizes. Application: For handling all chemical process requirements like acids, alkalis, corrosive slurries, hydrocarbons etc. Suitable for all liquids with/without solids Materials: Graded cast iron / WCB/CF8/CF8M (SS-316)/317/317L/CD4MCU/Alloy - 20/Hastalloy - B/ Hastalloy - C etc., If you have any inquiry about particular product then feel free to Contact us. Email:info@impetix.com Web:www.impetix.com Skype:impturno Cell: +91 98792 020860 Export Quality
MSG Inline Centrifugal Pump Size (discharge): 25mm to 450mm Capacity: 3.4~ 1200 m3/hr Head: 6m ~ 135 m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc MSG Inline Centrifugal Pump Introduction: MSG Inline Centrifugal Pump is a high-efficient, energy-saving product successfully designed by means of adopting the property data of MS model inline centrifugal pump and the unique merits of vertical pump and strictly in accordance with ISO2858 world standard and the latest national standard JB/T53058-93 and an ideal product to replace MS horizontal pump, DL model pump and other ordinary pumps. MSG Inline Centrifugal Pump Features: 1.Vertical structure, inlet and outlet diameters are same and on one center line, So it can be installed in pipe line like valves, it has compact and goodly externality, small floor area and low building investment, it can be used outdoor by add a shied on it. 2.Impeller mounted directly on the long axis of the motor, pump and motor bearing arrangement is reasonable, pump operation can effectively balance the radial and axial loads, thus ensuring the smooth operation of the pump,small vibration and low noise. 3.Mechanical shaft seal, use of imported titanium alloy seal ring, medium and high temperature mechanical seal with carbide materials, anti-wearing no leakage. 4.Easy installation and maintenance, no need to open pipeline system, the rotation parts of the pump can be pulled out by removing the screws on the pump. 5.According to the needs of flow and head, the pump can be used in series or parallel operation mode. MSG Inline Centrifugal Pump Parameter Selection Table: Model Flow(m3/h) Head(m) Speed(r/min) Power(Kw) Voltage(V) MSG15-80 1.5 8 2900 0.18 380 MSG20-110 2.5 15 2900 0.37 380 MSG20-125 2.5 20 2900 0.75 380 MSG20-160 2.5 32 2900 0.75 380 MSG25-110 4 15 2900 0.55 380 MSG25-125 4 20 2900 0.75 380 MSG25-125A 3.5 16 2900 0.75 380 MSG25-160 4 32 2900 1.5 380 MSG25-160A 3.7 28 2900 1.1 380 MSG32-100 4.5 12.5 2900 0.75 380 MSG32-125 5 20 2900 0.75 380 MSG32-125A 4.5 16 2900 0.75 380 MSG32-160 5 32 2900 1.5 380 MSG32-160A 4.5 28 2900 1.1 380 MSG32-160(I) 6.3 32 2900 2.2 380 MSG32-200 5 50 2900 3 380 MSG32-200A 4.5 44 2900 2.2 380 MSG Inline Centrifugal Pump Application: ▶Marine sea water ▶Cleanout system. ▶Every series of food machining and medicine produce ▶Environment protect system. ▶Waste water treatment for papermaking, metallurgy, galvanization, smelting, dye. ▶Electroplate and Dyeing system. ▶Industrial and chemical sump treatment ▶Explosion proof motor for oil, alcohol and other explosive liquid
MDG Boiler Feed Water Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc. MDG Boiler Feed Water Pump Introduction: MDG Boiler Feed Water Pump can deliver clear water without solid particles or other liquid which the physical and chemical feature is similar with clear water. The boiler hot water circulating pump is suitable for boiler feed water or feed water of high-pressure boiler. The temperature range of liquid is from -20 ¡ãC to -150 ¡ãC and the inlet pressure of pump is less than 0.6 Mpa. MDG Boiler Feed Water Pump Features: 1) Stator parts of the MDG boiler feed water pump : It mainly consists of suction stage, mid-stage, discharge stage and diffuser; they are strained through a lever and form a working chamber. the inlet and the outlet are vertival upword. 2) Rotor parts of the MDG boiler feed water pump : It mainly consists of shaft, impeller, balance kettle and shaft sleeve. Shaft transfers power to impeller and make the pump work. The axial force is balanced by balance disc (kettle) and there is rechargeable shaft sleeve in shaft to protect shaft. 3) Bearing parts of the MDG boiler feed water pump: It mainly consists of bearing body, shaft cover and sliding bearing. There are two single centripetal ball bearing in bearing body to prevent balance disc (kettle) from abrasion. The sliding bearing is lubricated by dilute oil, there is cooling chamber in bearing body and the bearing can be cooled with exterior water. 4) Shaft seal parts of the MDG boiler feed water pump : Shaft seal uses soft packing seal. It mainly consists od seal box, packing, packing ring and packing cover. The shaft is sealed, cooled and lubricated by exterior water from seal chamber. The mechanical seal can also be used as requirement and it need be cooled, lubricated and washed by exterior water. 5) Drive: Type MDG boiler feed water pump is directly driven by motor through flexible coupling. View from motor end, the rotating direction of pump is clockwise. MDG Boiler Feed Water Pump Parameter Selection Table: Model Speed(r/min) Flow Head(m) Power(KW) NPSH (m) m3/h L/S Shaftpower Motorpower MDG6-25×3 2950 3.75 1.04 76.5 2.37 5.5 2.0 6.3 1.75 75 2.86 2.0 7.5 2.08 73.5 3.19 2.5 MDG6-25×4 2950 3.75 1.04 102 3.16 7.5 2.0 6.3 1.75 100 3.81 2.0 7.5 2.08 98 4.26 2.5 MDG6-25×5 2950 3.75 1.04 127.5 3.95 7.5 2.0 6.3 1.75 125 4.77 2.0 7.5 2.08 122.5 5.32 2.5 MDG6-25×6 2950 3.75 1.04 153 4.73 11 2.0 6.3 1.75 150 5.72 2.0 7.5 2.08 147 6.39 2.5 MDG6-25×7 2950 3.75 1.04 178.5 5.52 11 2.0 6.3 1.75 175 6.67 2.0 7.5 2.08 171.5 7.45 2.5 MDG6-25×8 2950 3.75 1.04 204 6.31 15 2.0 6.3 1.75 200 7.63 2.0 7.5 2.08 196 8.58 2.5 MDG6-25×9 2950 3.75 1.04 229.5 7.10 15 2.0 6.3 1.75 225 8.52 2.0 7.5 2.08 220.5 9058 2.5 MDG6-25×10 2950 3.75 1.04 255 7.89 18.5 2.0 6.3 1.75 250 9.53 2.0 7.5 2.08 245 10.63 2.5 MDG6-25×11 2950 3.75 1.04 280.5 8.68 18.5 2.0 6.3 1.75 275 10.5 2.0 7.5 2.08 269.5 11.71 2.5 MDG6-25×12 2950 3.75 1.04 306 9.47 18.5 2.0 6.3 1.75 300 11.44 2.0 7.5 2.08 294 12.78 2.5 MDG Boiler Feed Water Pump Application: This series boiler feed water pump is used for transport no solid particles contained water or Chemical and Physics water Boiler feed water and boiler circulation water High-rise building booster Urban Fire booster Long distance water transportation Boiler heating and cooling water circulation booster
MX Self Priming Pump Size (discharge): 25mm to 450mm Capacity: 3.4~ 1200 m3/hr Suction lift: Max. 6.5m Head: 6m ~ 135 m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc MX Self Priming Pump Introduction: MX Self priming pump made by our company is developed after our digestion, assimilation and improvement of domestic and foreign relevant technical data, which is a energy-saving kind of pump production. The pump is a kind of self-suction centrifugal pump, which has the advantages of compact structure, convenient operation, steady running, easy maintenance, high efficiency, long life, strong self-suction ability and so on. It doesn't need a foot valve on the pipeline, and just need to ensure that there is quantificational inducting oil stored in the pump case before work, so as to simplify the pipeline system and improve the working condition. MX Self Priming Pump Features: 1. Beautiful shape and fine structure,reliable performance. 2. With strong capacity of self priming, no need to equip with flap valve. 3. Non-clog, and with powerful capacity of passing big solid.. 4. Convenient for maintenance. MX Self Priming Pump Parameter Selection Table: MX Self Priming Pump Application: It is used in environment protection,construction,fire protection,chemical industry,phamary,printing and dyestuff,brewage,elctric power,electroplate,papermaking,petrol,washing for industry and mine,cool for device,etc. It is suitable for clear water,sea water and chemical medium with acid and alkali and mushy slurry(viscosity100 centipois),consistency for solid can not exceed 30% of total medium. When it's mounted with an arm sprayer, it can jet the water into the air to disperse into little raindrops for spraying, so it is a good tool for farm, nursery, orchard and tea garden. It is the ideal supporting pump for transfer slurry to filter press, it could matching with filter press of different specs and models.
MD Multistage Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc. MD Multistage Pump Introduction: Multistage Pump is single-suction,multistage,centrifugal pump,It is widely used for water supply&drainage infields of factories mines and cities.It is provided for delivering clear water without solid particles or other liquid which is physically and chemically similar to clear water. The temperature of the liquid is 0¡ãC~80¡ãC. Permissible inlet pressure is 0.6MPa MD Multistage Pump Features: 1. Stator: The main parts are suction casing, stage casing, discharge casing and diffuser. They are screw up by poles, to become a working house. It is horizontal, the discharge direction is upward; The discharge and suction direction of them are both upwards, and the suction direction is horizontal usually, also they can be made upward according to user's requirement. 2. Rotor: It is consist of shaft, impellers, balance dic and shaft sleeve etc. Shaft supplied power to impellers; The axial force is balanced by balance disc; The sleeve mounted on shaft to protect shaft. 3. Bearing parts: It is consist of bearing body, bearing and bearing cover etc. The bearing of type 85-67, 155-67, 600-60 pump is sliding bearing, lubricated by diluted oil, the other pump bearing is rolling bearing, lubricated by grease. 4. Shaft seal: It is usually adopted soft packing seal, consist of sealing house on suction casing, packing, blocking water ring, the sealing hose have some pressure water, to cool, lubricate and seal pump. The pumps usually adopt mechanical seal. 5. Drive: The pump is driven directly by motor through elastic coupling, the rotation of pump is clockwise looking from motor to pump. MD Multistage Pump Parameter Selection Table: MD Multistage Pump Application: Water supply and discharge in high-rise buildings Fire water supply in constructions Water supply and discharge in factories and mines Long distance delivery Cyclic pressurization in production
Supplier: Slurry pump, rubber slurry pump, vertical slurry pump, gravel pump, froth pump, dredge pump, FGD pump, sewage pump, clean water pump, slurry pump spare parts
Supplier: Slurry pump and pump parts
