Specifications: Input: ac 100-240v, 50/60hz Output: 12v 3a, 15v 4a, 16v 4a, 15v 3a, 12v 2a, etc. Certificates: saa, c-tick, fcc, cb, ul, kc, ce, gs, pse Materials: pc + abs Color available: black
Product Introduction SANDI AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-750VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface (Optional)
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Universal Input: 100~240VAC 50~60Hz Protections: Short circuit/ Overload/ Over temperature O/P: High accuracy, low noise; hold up time¡Ý20mS Cooling by free air convection; Auto recovery; Operation temperature: -40¡æ~+70¡æ; 100% full load burn-in test for 8 hours High Efficiency, high reliability; Built-in Class B EMI Filter Long life of 50,000Hours, 2 years warranty Compliance to EN61347-2-13 /IEC61347-2-13 /UL8750.
Universal Input: 100~240VAC 50~60Hz Protections: Short circuit/ Overload/ Over temperature O/P: High accuracy, low noise; Hold up time 20mS Cooling by free air convection; Auto recovery; Operation temperature: -10~+50; 100% full load burn-in test for 8 hours High Efficiency, high reliability; Built-in Class B EMI Filter Long life of 50, 000Hours, 2 years warranty Compliance to EN60950 /IEC60950 /UL60950.
Model Mx12x6 Product name Tablet adapter 5v 2a Certification Ce/ul/kc Color White and black Oem/odm Yes Transfer type Ac/dc Output voltage 5v Output current 2a Output power 10w Input voltage 100-240v Input current 0.3a Input frenquency 50/60 hz Protection Ocp ovp opp scp Ac plug Cn, eu, us, uk, au, kc available Dc cable length 1.2m/1.5m/1.8m Dc connector 5.5*2.5*10, 5.5*2.1*10, 3.5*1.35*10 etc Efficency V Warranty 1 year Load regulation
1, Input: 100 to 240V AC, 50/60Hz 2, Output power: 24W series 3, Output voltage: 3 to 24V DC 4, Output current: 10 to 4,000mA 5, Overload protection 6, Output over voltage protection 7, Short circuit protection 8, High efficiency Mini 75 % 9, DC socket (optional) 10, CEC power supply standard 11, CE approved 12, No Load Power Consumption ¡Ü 0.3 W at Rated Voltage 13, Ripple And Noise: Output voltage 1% 14, High-Voltage test : Primary to secondary: 3 kV 5 mA 60 S 15, Leakage Current : 0.5 mA (max) at input 240Vac 16, Operating Temperature Range 0--40¡æ 17, Storage Temperature Range: -20 --- 85¡æ 18, High Humidity Operation :+ 40 ¡æ and 90 ¡« 95% Humidity 19, Dimension : 74.0mm*41.0mm*47.5mm 20, Net weight: About 170 gram per unit. 21, Color : Black / White 22, The power adapter should have 50,000 hours according to MTBF. 23, Insulation Resistance:Primary to Secondary : 50 Meg. Ohms min. 500VDC. Customized.
Supplier: Switching power supply, power adapter, charger, power supply
Model: 30V 333mA Power Supply Cord for HP 0957-2286 0957-2290 0957-2398 Deskjet 1050 1000 2050 1051 1055 1056 2060 2512 3050 3050A 3015A 3052A 2514 3051A 3510 3511 3512 3055 3515 Output: 30V 333mA Power cord: UK US EU AU Power Cord Outlet: 2/3 prong Size: 15X15X6 cm (L x W x H) Packing: Brown box with pe bag and bubble bag; 49*39*34CM(L x W x H) for a master carton size Delivery Date: Within 2-3 working days after confirming the payment Test: Temperature test; Vibration test; Drop-Test; Overcharging and discharging test Line Regulation: +/-5% Load Regulation +/-5%
