Imextra

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

The rubber handle can make kids feel comfortable when they pull or push. Also, they can maneuver conveniently with it. 2. 6"large wheels make kids easily moving on the sand and ground. The PP wheels with excellent grip is wear-resistant and anti-slipping. 3. Made of durable metal construction and coated with paint, this wheelbarrow with wheels features durable construction and weather resistance. 4. The crane toy can not only use on summer, it is great for sand, dirt, and snow. Specifications: 1. Overall Size: (29 x 13.6 x 16.5)" / (73.66 x 34.54 x 41.91)cm(L x W x H). 2. Weight Capacity: 66lbs / 29.94kg 3. Test: Astm-F963-17 4. Ageï¼?3 Years And Up Package Includes: 1 x Wheelbarrow 1 x Manual

Sizes: H Beam, I Beam, Structural Angle, Steel Channel

Product Name : Carbon steel angle Surface : Pickling, Phosphating, Galvanizing Edge : Plain Mill Standard : ASTM DIN GB JIS EN AISI The angle steel is mainly used to make frame structures, such as high-voltage transmission towers, frames on both sides of the main beam of steel structure bridges, columns and booms of tower cranes on construction sites, columns and beams of workshops, etc., small places such as flower pot shaped shelves at the festival roadside, and shelves with air-conditioning and solar energy hung under windows. Angle steel is also widely used in building structures and engineering construction, such as house beams, power transmission towers, lifting and transportation machinery, ships, industrial furnaces, reaction towers, container racks and warehouse shelves. Warehouse Storage * Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project Packing and shipping * Our products are exported to multiple overseas countries and regions such as Europe, America, South Asia, Southeast Asia, Africa, and Latin America, and have won the trust and support of customers with excellent quality and service. * During the supply process, the company can timely use sufficient funds to adjust the production variety and model of the steel plant, ensuring the use needs during the peak construction period Application field * The company adheres to the corporate spirit of never being satisfied and striving to surpass, and continuously creates new brilliance with the new economic concept of continuous innovation. Reward guests and friends from all over the world with satisfactory service. Our company is willing to cooperate closely with friends from all walks of life at home and abroad, and work together to create a better tomorrow

* H-beam is a kind of Economic section steel, which sectional area distribution is more optimized, the ratio of strength to weight is more reasonable, Mechanical properties of section is more better.It is developed from the I-section steel optimization of a better section mechanical properties of the economic section steel, because its section is same as the English letter "H" ,so be named as H-Beam. Because the various part of H-beam is arranged at right angles, H-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, so it has been widely used. * H-beam as a new type of economic construction steel. The section shape of H-beam steel is economical and reasonable, the mechanical properties are good, and the elongation of each point on the section is uniform and the internal stress is small. Compared with the ordinary I-beam steel, it has the advantages of more large section modulus,more light weight and more saving metal, which can reduce the building structure by 30-40%. * And because its legs inside and outside parallel, leg end is a right Angle, assembled into components, can save the workload of welding and riveting up to 25%. It is often be used in large buildings (such as workshops, high-rise buildings, etc.), as well as Bridges, ships, lifting and transportation machinery, equipment foundation, supports, foundation piles, etc. Product : Carbon Steel H beam Standard AISI, ASTM, BS, DIN, GB, JIS, etc Web Width: 100-900mm Thick: 5-16mm Flange : Width:100-400 Thick: 7-34mm Length : 5.8m-12.0m or as your requirement Packing details : In bundle with 6 circles of steel strip, each bundle about 2mts. Surface : Pickling, Phosphating, Galvanizing Inspection : BV,SGS,MTC,etc. Warehouse : Storage * Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project. Application field * The company adheres to the corporate spirit of never being satisfied and striving to surpass, and continuously creates new brilliance with the new economic concept of continuous innovation. Reward guests and friends from all over the world with satisfactory service. Our company is willing to cooperate closely with friends from all walks of life at home and abroad, and work together to create a better tomorrow

* Stainless H beam is widely used in beams and columns of industrial and civil steel structures. Steel structure load-bearing supports for industrial structures. Ship and machinery manufacturing frame structure. Steel piles and supporting structures of underground works. * H-beam is a kind of Economic section steel, which sectional area distribution is more optimized, the ratio of strength to weight is more reasonable, Mechanical properties of section is more better.It is developed from the I-section steel optimization of a better section mechanical properties of the economic section steel, because its section is same as the English letter "H" ,so be named as H-Beam. Because the various part of H-beam is arranged at right angles, H-beam has the advantages of strong bending resistance, simple construction, cost saving and light structural weight in all directions, so it has been widely used. Product : Stainless H beam Standard : AISI, ASTM, BS, DIN, GB, JIS, etc Web Width: 100-900mm Thick: 5-16mm Flange : Width:100-400 Thick: 7-34mm Length : 5.8m-12.0m or as your requirement Packing details : In bundle with 6 circles of steel strip, each bundle about 2mts. Surface : Sandblasting, solution pickling Inspection : BV,SGS,MTC,etc. Warehouse Storage * Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project Packing and shipping * Our products are exported to multiple overseas countries and regions such as Europe, America, South Asia, Southeast Asia, Africa, and Latin America, and have won the trust and support of customers with excellent quality and service. * During the supply process, the company can timely use sufficient funds to adjust the production variety and model of the steel plant, ensuring the use needs during the peak construction period.