Frame size=42mm(nema17) Holding torque=6.5kg.Cm Rated current=1.2a Step angle=1.8deg, 200steps/rev Shaft diameter=5mm Good standard export carton with foam
This item inculdes : 1 PC Closed loop Stepper Motor Nema23 57HBM10-1000 4A 110N-cm(155oz-in) 1 PC Mactching Driver WTSS570 Technical Specifications Part No.: 57HBM10-1000 Frame Size: NEMA34 Step Angle: 1.8 degree Voltage: 1.6V Current: 4.0A/phase Resistance: 0.44 Ohm/phase Inductance: 1.2 mH/phase Holding torque: 1.1N.m 155oz-in Rotor inertia: 300g-cm2 Number of wire leads: 4 Weight: 2 kg Length: 77mm
Introduction The d2hb882mb is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80vdc Suitable for-2-phase and 4-phase motors Output current up to 5.86a Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200khz Automatic idle-current reduction Small size (107*97*48), weight:1kg
Introduction The d2hb542ma is an economical microstepping driver based on patented technology of longs motor.It is suitable for driving 2-phase 4-phase hybrid stepping motors .By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as l/r drivers .Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Features Low cost and good high-speed torque Supply voltage up to +45vdc Output current up to 5.86a Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200khz Dip switch current setting 8 different values Small size (122.2*90*33), weight:0.3kg
SD-2H086MB Features Low cost and good high-speed torque 14 selectable resolutions Supply voltage up to +80VDC Suitable for-2-phase and 4-phase motors Output current up to 5.86A Dip switch current setting 8different values Optically isolated input signals Pulse frequency up to 200KHz Automatic idle-current reduction Small size (107*97*48),Weight:1KG
SD-2H044MA Features Low cost and good high-speed torque Supply voltage up to +45VDC Output current up to 5.86A Optically isolated input signals Automatic idle-current reduction 14 selectable resolutions Suitable for-2-phase and 4-phase motors Dip switch current setting 8 different values Pulse frequency up to 200KHz Dip switch current setting 8 different values Small size (122.2*90*33),Weight:0.3KG
Q2HB88M Features (1) High performance, low price (2) Two group 32 channels constant angel and constant torque subdivision. Highest subdivision: 480 (3) The motor phase current is reduced to set current value 100 ms after receiving the last pulse edge (4) Bipolar constant current chopping circuit (5) Opto-isolated input/output (6) Driven current is adjustable continuously from 0.5A/phase to 8A/phase (0.4A/phase to 6.4A/phase) (7) Single power supply, voltage arrange from DC24/V to 80V (DC40V to130V) (8) Highest response frequency: 200Kpps (9) Over voltage protection, overheat protection, over current protection
PMD006P3E is a kind of micro integrated stepper motor microstepping driver, which can be directly installed in the rear 42/57/86 etc series stepper motor, and which has the advantages of small size, strong driving force, and low heat and so on. PMD006P3E stepping motor driver can provide 0~6 continuous adjustable peak current, maximum 128 microstepping, free current which can be adjusted continuously.
Brake Disc Main Size, Weight And Moment Of Inertia Disc diameter D T K S D3max Inertia Moment kg  m2 Weight kg I II I II I II 315 15 10 42 180 155 0. 116 0. 11 8.5 6. 7 355 15 10 54 200 175 0. 192 0. 178 11.4 9. 9 400 15 14 54 255 230 0. 32 0. 29 15.2 12.4 450 15 16 54 305 280 0. 55 0. 46 19.7 15.6 500 15 18 54 325 295 0. 83 0.71 25 20 560 15 18 54 350 320 1.28 1. 13 30. 7 25.6 630 15 20 54 400 360 2. 06 1.83 38.8 33 710 15 20 54 480 420 3. 32 2.9 46.5 39.4 800 15 24 70 540 500 5. 87 4.8 67.8 52.7 900 15 24 70 600 560 9.3 7.9 86.6 70.3 1000 20 30 80 620 560 17.4 15. 7 128.8 115. 1 aluminum casting hardness , aluminum casting house , aluminum casting history , aluminum casting hazards , aluminum casting holes , how to make molds for aluminum casting , how to make a sand mold for aluminum casting , how to do aluminum casting , home aluminum casting , howmet aluminum casting inc , how to make aluminum casting sand , how to make permanent molds for aluminum casting , high strength aluminum casting alloys
