Psyllium Husk Powder: Psyllium husk powder is the pulverized form of husk. Its gradient depends on its sieve size. It is cooling, laxative, anti-diabetic, antichronic, soothing, etc. Specifications: All the specifications are same as per psyllium husk. Mesh a size varies from 40# to 100# is available as per demand. Applications: Main use in pharmaceutical formulations, lubricating laxative. Useful in the treatment of intestinal tract problems like constipation and other minor disorders. It is commercially used in Ice-creams as a substitute of sodium alginate as a stabilizer. Also used in fresh fruit drinks, Jam, Bread, Biscuits, Rice cakes, instant noodles, breakfast cereals, etc. Improves Softness and Texture, works as binder and stabilizer in pharmaceutical industry. To avoid the stickiness in throat and mouth some companies prepare capsules for regular consumption.
Soap Nuts [Sapindus Murokossi] with seeds, without seeds and powdered can be supplied with Organic Certification and USDA Certified in bulk.
SVR3L is made from latex harvested from our rubber plantation. It can meet customer's strict requirement about some of technicalities such as: the Po, Color (Lovibond), This product is being applied in many fields: advanced automobile tire, wire belt, wire cable, sole of shoes, medical products, industrial electronics,
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Soursop Leave have Acetogenin containing compounds namely bulatacin, asimisin and squamosin. Acetogenin acts as an anti- feedent. Thus, they are often used in killing insects and pests which die by consuming these leaves even in small amounts. Product Type: FLAVORED TEA Type: Herbal Tea Variety: Mint Tea Processing Type: Raw Specialty: Organic Tea, SLIMMING TEA Packaging: Bag, Box, Gift Packing, Vacuum Pack Certification: Gap, ISO Grade: A Shelf Life: 2 years Place of Origin: Vietnam Color: Yellow Green Shape: Whole Part use: Leaf
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�?�°C to 1250�?�°C with a boiling point of 2355�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customer strict requirement about some of technicalities such as: the PO, Color (Lovibond), Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash.
SVR3L is made from latex harvested from our rubber plantation. It can meet customer's strict requirement about some of technicalities such as: the PO, Color (Lovibond), SVR3L is made from latex harvested from our rubber plantation. It can meet customerâ??s strict requirement about some of technicalities such as: the PO, Color (Lovibond), â?¦ Latex is preserved by ammonia or sodium sulfite. Then coagulated with formic acid, followed by shredding by passing through a rolling mill, washing system and hash. After the crumb rubber is dried, it will be compressed into blocks and packed in polyethylene bags
